Reviews Servo To Multiplexer Board

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
The chip is compatible with 3V and 5V and can be used with any logic level.

Basic Stamp microprocessor, the board uses sensor inputs, a program, and servo outputs to operate a robot using the Parallax pBasic language.
Features include 8 sensor inputs and 5 servo outputs, all with polarized connectors as well as a built-in piezo "speaker".
Holes on side on the side of the board bolt to Merkur parts.

Package includes: you will 9 pieces of servo extension cord, 3 pieces of male JST to female JR (Futaba) cable, 3 pieces of male to 2 female Y harness, 3 pieces of male to 3 female Y harness.
Abundant quantity and diverse styles that can meet your various needs.
Appropriate sizes: the servo extension cord measures approx. 15 cm/ 5.9 inches in length, universal size for your use, the color is white, black and red.
Extensive usages: these JST male to female are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
Well made: JST connector is made of quality PVC material, with good insulation and flame retardant.
The interior is made of tinned copper, which has a good transmission and low resistance.
Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control unit, which is male to female.

3-Pin JR plug male to male connector servo extension lead wire cable..
There is a 3 pin JST RE connector on each end. This is a simple 3 wire cable. Ideal for jumping from board to board, or something else..
Practical range: For Airplane, Helicopter, Quad co-pterter , Multi-coater RC car servo connection or receiver connection..
Packaging quantity ：10 Pcs * 10cm JR 3pin male to male plug servo extension cables wires cords leads..

You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.

Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
2.You should connect higher power supply for higher-power servo.
3.Make sure servo are connected properly, otherwise they will not move..
Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..

74HC4051 8-Channel-Mux Multiplexer Selector Module Distributor Resolver CJMCU-4051 Development Board.

Function: Use 16 ADCs to collect 16 analog signals.003cbr003e.
Use the CD74HC4067 16-channel analog signal switch.
Analog signal input: C0-C15 16 channels.003cbr003e.
This is a breakout board for the very handy 16-Channel Analog / Digital Multiplexer / Demultiplexer CD74HC4067.003cbr003e.
This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.003cbr003e.

Function: Use 16 ADCs to collect 16 analog signals..
Use the CD74HC4067 16-channel analog signal switch.
Analog signal input: C0-C15 16 channels..
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction..

The 4Ch Video Color Quad Multiplexer allows several video signals from CCTV security cameras or other analog video devices to be combined and displayed on one monitor. The video processors are also commonly referred to as video mux, CCTV multiplexer, or color quad processor..
4 Channel Color Quad Multiplexer, Loopout Function, Build-In Buzzer.
Multiple Display Modes: 4 pictures, 2 pictures, 1 picture.
Video Input: 1.0Vp-p75 ohm, Tape Input/Output: 1.0Vp-p75 ohm.
Working Voltage: DC12V/1A, Environmental Temperature: -30°C-60°C.