Reviews Straight Spindle

The ROP Shop Pack of 4 Trailer Axle Kits with 4 on 4 Bolt Idler Hub & 1 Round BT8 Spindle

  • Replacement (Pack of 4) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (4) Idler Hub with Lug Nuts, (4) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (8) Inner/Outer Bearings, (4) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (4) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

The ROP Shop (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle

  • Replacement (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

The ROP Shop (Pack of 8) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle

  • Replacement (Pack of 8) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (8) Idler Hub with Lug Nuts, (8) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (16) Inner/Outer Bearings, (8) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (8) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

Makita JS8000 Fiber Cement Shear

  • Single-piece cutting head is machined from precisely milled aluminum to ensure blades cut straight.
  • Solid steel blades cut clean, straight lines with a maximum cutting capacity up to 5/16".
  • Protected drive spindle withstands heavy torque loads from powerful 6.5 AMP motor.
  • Large variable speed trigger with lock-on button for operator convenience.
  • Ergonomically designed rubberized "pistol grip" for increased comfort.
Check Stock

Livinia Toto Malaysian Oak Dining Chair Set of Two, Country Farmhouse High Spindle Back Wooden Side Chairs (Black)

  • 【SET OF TWO】 Your purchase includes a set of two side chairs. Perfect as office desk chairs or as dining chairs in the kitchen and restaurants, especially for those who love genuine wooden products. Choose from the 3 color variations..
  • 【SPINDLE BACK DESIGN】 Lower seats with the classy long, high spindle back and wide seating make this chair adorable and elegant at the same time, while also keeping you comfortable.
  • 【BUILT STURDY】 Completely made of natural Malaysian Oak, the chair is built to be sturdy and durable. The arched high spindle back is not only aesthetically pleasing but also provides comfortable backrest. The ergonomically designed and wide seating will provide you comfortable seating for a long duration of time..
  • 【EASY ASSEMBLY】 Straight forward, easy assembly required with instruction, parts and hardware included..
  • 【DIMENSIONS】 18.9" x 19.2" x 33.2" The seating may be lower than your typical dining chair, so be sure to check the dimensions!.
Check Stock

WEN HA5932 5-Amp Variable Speed Portable Oscillating Spindle Sander

  • Lightweight and portable design allows for easy handheld sanding in hard-to-reach places.
  • Easily transform your portable handheld unit into a stationary benchtop spindle sander by clamping it to your workbench with the included mounting hardware.
  • Powerful 5-Amp variable speed motor provides anywhere from 1800 to 3200 rotations and 50 to 90 oscillations per minute with a 1/4-inch stroke.
  • Features four different sanding spindle diameters: 1/2 inch, 3/4 inch, 1 inch, and 1-1/2 inch spindles.
  • Includes four 80-grit sanding sleeves, three rubber drums, one non-marring rubber mounting pad, Two clamps, an adjustable Straight-edge guide Plate, an onboard 1-1/2-inch dust port, and a two year warranty.
Check Stock

Livinia Toto Malaysian Oak Dining Chair Set of Two, Country Farmhouse High Spindle Back Wooden Side Chairs (Natural Oak)

  • 【SET OF TWO】 Your purchase includes a set of two side chairs. Perfect as office desk chairs or as dining chairs in the kitchen and restaurants, especially for those who love genuine wooden products. Choose from the 3 color variations..
  • 【SPINDLE BACK DESIGN】 Lower seats with the classy long, high spindle back and wide seating make this chair adorable and elegant at the same time, while also keeping you comfortable.
  • 【BUILT STURDY】 Completely made of natural Malaysian Oak, the chair is built to be sturdy and durable. The arched high spindle back is not only aesthetically pleasing but also provides comfortable backrest. The ergonomically designed and wide seating will provide you comfortable seating for a long duration of time..
  • 【EASY ASSEMBLY】 Straight forward, easy assembly required with instruction, parts and hardware included..
  • 【DIMENSIONS】 18.9" x 19.2" x 33.2" The seating may be lower than your typical dining chair, so be sure to check the dimensions!.
  • 【CUSTOMER SERVICE】 If you have any problems or questions about your purchase or any other products for sale, our customer service representatives will assist you in any way necessary. Feel free to contact us anytime!.
Check Stock

THINBIT 3 Pack LGPT062D2L 'L' Series, Uncoated Carbide, Parting Insert for Steel, Cast Iron and Stainless Steel with Interrupted Cuts

  • See Downloads section below item photos for detailed product information, technical information and compatible toolholders..
  • Narrow widths reduce material loss and part deflection. Perfect for precious metals, thin wall tubing and small diameter parts. Cuts flush to collet face or shoulder on main spindle side using M04 or sub-spindle side using M03..
  • Use for parting solid stock up to 1.000" or tubing with wall thickness up to .500"..
  • Uncoated DURA-MAX 2000 carbide parting insert for steel, cast iron and stainless steel with interrupted cuts..
  • Use with Large series toolholders. Use LH straight or RH 90 degree toolholder..
Check Stock

THINBIT 3 Pack LGPT045D2R 'L' Series, Uncoated Carbide, Parting Insert for Steel, Cast Iron and Stainless Steel with Interrupted Cuts

  • See Downloads section below item photos for detailed product information, technical information and compatible toolholders..
  • Narrow widths reduce material loss and part deflection. Perfect for precious metals, thin wall tubing and small diameter parts. Cuts flush to collet face or shoulder on main spindle side using M03 or sub-spindle side using M04..
  • Use for parting solid stock up to 1.000" or tubing with wall thickness up to .500"..
  • Uncoated DURA-MAX 2000 carbide parting insert for steel, cast iron and stainless steel with interrupted cuts..
  • Use with Large series toolholders. Use RH straight or LH 90 degree toolholder..
Check Stock

THINBIT 3 Pack LGPT025D5R 'L' Series, Uncoated Carbide, Parting Insert for Non-Ferrous Alloys, Aluminium and Plastic Without Interrupted Cuts

  • See Downloads section below item photos for detailed product information, technical information and compatible toolholders..
  • Narrow widths reduce material loss and part deflection. Perfect for precious metals, thin wall tubing and small diameter parts. Cuts flush to collet face or shoulder on main spindle side using M03 or sub-spindle side using M04..
  • Use for parting solid stock up to .400" or tubing with wall thickness up to .200"..
  • Uncoated DURA-MAX 5000 carbide parting insert for non-ferrous alloys, aluminium and plastic without interrupted cuts..
  • Use with Large series toolholders. Use RH straight or LH 90 degree toolholder..
Check Stock