Reviews Vertical Pump Manufacturers

The ROP Shop | 2400 PSI Power Pressure Washer Water Pump for Excell & Devilbiss VR2400, VR2500

. 3 Bolt Pattern: 7 11/16” x 6 3/16” x 6 7/16” & 4" Center to Each Outer Hole. Maximum Water Temperature: 140° F. Inlet Connection Type: Standard Garden Hose. Outlet Tube Connection: 22mm Male. Refer to images 2 and 3 for more information.
Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube (come installed).
This pump is for vertical gas engine driven units. In some instances, the pump may need to be removed to change engine oil. The mounting flange provides a convenient connection to most 7/8” diameter shaft vertical gas engines in 4.5-7 HP. The pump has a hole in the leg for draining the engine oil. The pump includes a built-in pressure control valve, downstream chemical injection system and thermal relief valve.
This has the outlet facing the front. Some specific pressure washers may require longer bolts and spacers to mount the pump to your engine. These bolts and spacers are NOT included, but may be purchased at your local hardware store. Common bolt sizes: Two - 5/16" 18 x 2 1/2", ....

GRINDER PUMP: 3/4 HP cast iron submersible sewage grinder pump with vertical float switch..
SEWAGE GRINDING TECHNOLOGY: New grinding technology for sewage applications to eliminate solids. Reduces clogging of impeller and jamming situations.
PUMPING CAPACITY: High lift capacity of 35 feet with automatic vertical float switch.
SEWAGE PUMP APPLICATIONS: Recommended for a residential sewage pump application..

Primary pump-pumps up to 4200 gallons per hour, pumps water up to 25 vertical feet.
Pre-assembled kit: Primary pump model 92511 cast iron sump pump and 12V DC backup pump.
Kit includes 87 decibel alarm, electronic control panel with indicator lights, battery box, mounting hardware, 2 AMP DC charger (12 volt deep cycle battery not included).
Vertical float switch on primary and backup pumps.

3.5-Gallon Tri-Poxy tank for durability and a 4-inch wide mouth opening for easy filling and cleaning.
Compatible for most professional concrete applications, suitable for homeowners too (check chemical manufacturers instructions).
Brass pump, wand, 2 female brass fan nozzles and shut off with lock on feature. Poly holster keeps wand and nozzles secure.
Chemical resistant seals and gaskets designed to handle a variety of chemicals (check chemical manufacturers instructions).
Unique Tri-Lock seal feature that locks the pump cap tight.

2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6 3/16” x 6 7/16” & 4" Center to Each Outer Hole. Maximum Water Temperature: 140° F. Inlet Connection Type: Standard Garden Hose. Outlet Tube Connection: 22mm Male. Refer to images 2 and 3 for more information.
Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI. Pump head can be flipped.
This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine or can't reach the under side of frame such as the engine has a longer shaft. If spacers aren't used when installing, the pump legs will break from stress.

1/2 HP Sump pump moves up to 3,300 gallons per hour.
pump will lift water up to 25' of vertical height.
Vertical float switch to automatically turn the pump on/off.
1-1/2 inch NPT discharge for high capacity pumping.
Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested.

1/3 HP Sump pump moves up to 2,880 gallons per hour.
pump will lift water up to 25' of vertical height.
Vertical float switch to automatically turn the pump on/off.
1-1/2 inch NPT discharge for high capacity pumping.
Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested.

12 Volt Sump pump moves up to 1,380 gallons per hour.
pump will lift water up to 25' of vertical height.
Vertical float switch to automatically turn the pump on/off.
1-1/4 inch or 1-1/2 inch NPT discharge for high capacity pumping.
Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested.

1/3 HP Sump pump moves up to 2,760 gallons per hour.
pump will lift water up to 25' of vertical height.
Vertical float switch to automatically turn the pump on/off. Switch on and off point is 6 and 2 inches.
1-1/2 inch NPT discharge for high capacity pumping.
Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested.

OEM replacement pump for your pressure washer: Fit most 7/8" shaft vertical gas pressure washer engines. Compatible for Craftsman, Subaru, Homelite, Ryobi, Honda, Husky and more. This easy-to-install kit is great for power washers that can support up to 3000 PSI at 2.5 GPM to wash cars, sidewalks, fences, vehicles, and more..
Easy start & maintenance-free: This pump pre-fill oil for lifetime, so you never have to change the oil. It is also manufactured from fully die-cast aluminum for good against corrosion. If the pressure washer is not used for a long time, we recommend that you uses a anti-freeze and lubricant formula, for use before extended storage and prior to startup the following season to keep your pump running on full blast..
Easy installation: This replacement pump features a threaded M22 connection pressure washer hose outlet, 3/4'' NH garden hose inlet. The standard bolt pattern fits most 7/8'' vertical shaft gas-powered pressure washers. Packet includes a chemical hose with filter, mounting bolts, shaft key, and instruction booklet to get your pressure washer back in life within 10 minutes. (*Fit 7/8'' vertical shaft engines ONLY).
A high-quality thermal relief valve is matters: It protects the pump from overheating while in bypa....