Reviews Obdbattery Voltage

ANCEL PB100 Automotive 12/24V Power Circuit Tester Probe with ANCEL BA301 6V 12V Battery Load Tester Car Cranking Charging System Test Tool

  • Includes: 1 x PB100 Circuit Tester, 1x BA301 Battery Tester.
  • A MUST-HAVE TOOL - Designed for voltage & polarity testing, continuity testing, signal circuit testing, supply power/activating components, trailer lights & connections testing. It features red/green polarity indicators, follows & locates short circuits, and checks bad Ground contacts..
  • 4 WORKING MODES - DC Voltage mode for reading the DC voltage with a resolution of 0.1 volts.
  • AC Voltage mode for reading the Max. voltage, the Min. voltage, and frequency.
  • Resistance mode for reading the resistance between the tip and auxiliary ground lead.
  • Diode mode for checking forward bias or reverse bias..
  • Works on all 6V & 12V 100 - 2000 CCA lead-acid batteries, analyzes starter cranking and alternator charging condition. Cranking test to test and analyze the starting motor (cranking time, voltage, and status), and the charging test to check and analyze the charging system (load voltage, unloaded voltage, ripple status, charging system status)..
  • Features one-click "waveform" to record the voltage changes (current voltage, maximum and minimum voltage) in a graph during ignition. You'll know if the battery needs to be replaced or not through analyzing the values of discharge voltage, starting voltage, and ch....
Check Stock

High Voltage DC-DC Boost Converter 1.5V-3V to 300V-400V 380V Adjustable Step-up Voltage Booster Power Supply Module

  • 3V DC boost power module, High-voltage sensors, Quiescent current 12mA, Size: 58x17x14mm/2.28x0.66x0.55inch.
  • Input voltage 3V, the output voltage adjustable range of 300V-400V (this circuit is not added voltage regulator circuit, the input voltage decreases the output voltage will drop)..
  • When the high voltage output is connected with a load, the on-board vibrator wiring terminal will have 3V voltage output (also can be connected in series with a LED and dozens of ohms resistanceas an indicator)..
Check Stock

PA 5.0 Farad digital Power Capacitor

  • 3 Digit Super Bright Blue Digital LED Voltage Display.
  • Audible Warning Tone for Reverse Polarity, Voltage Overload and Low Battery Voltage.8 Farads with digital voltage display.
  • Voltage Measurement Accurate to + / - 0.1 VDC.
  • Automatic Sleep Status When Volume Is Low Or There Is No Voltage Variation Present.
  • Capacitance: 8,000,000, Working Voltage: 16 VDC, Surge Voltage: 24 VDC.
  • Equivalent Series Resistance: 0.015 Ohm @ 100 Hz / 25°C, Capacitance Tolerance: + / - 10%.
  • Dimensions: 9 x 6 x 2, Unit Weight: 5.3 Lbs.
Check Stock

Klein Tools NCVT-3 Non-Contact Voltage Tester with Flashlight

  • Provides non-contact detection of AC voltage.
  • Detects 12 to 1000V AC with simultaneous visual and audible voltage indicators.
  • Bright flashlight illuminates work area and may be used independent of voltage detection function.
  • Visual LED bar graph indicates the presence of voltage – the higher the voltage sensed, or the closer to the voltage source, the more LEDs light up.
  • Bar graph visual voltage indicator utilizes up to five vibrant LEDs for easy interpretation/viewing.
  • Audible voltage indicator beeps at a greater frequency the higher the voltage that is sensed, or the closer to the voltage source.
  • Auto Power-Off conserves and extends battery life.
  • Screw-thread battery cap with O-ring ensures protection against dust and water ingress.
  • Lightweight, compact tool with pocket clip provides convenient storage and quick access.
Check Stock

[2 Pack] DC-DC 5A Buck Converter 4-38V to 1.25-36V Step-Down Voltage Regulator High Power Module with LED Display

  • 【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
  • 【Input Voltage】DC 4V to 38V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • 【Output Voltage】DC 1.25V to 36V voltage is continuously adjustable, maximum output current is 5A..
  • 【Mini Size】62*38*14 mm (with potentiometer). 2 sets included..
  • 【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).
Check Stock

BSEED Electronic Surge Protector for Home Appliance,Voltage Protector Suit for Refrigerators and Freezers, Voltage Brownout Outlet 220V 20A,4400Watts(1 Pack)

  • ✅Automatic Induction Protection: Protect your electrical devices by interrupting the current flow from voltage spikes, instant surge, voltage fluctuation, brownout, and that voltage which are too high or too low.(The printed text and instructions of this surge protector are in Spanish. If you have any questions, please do not hesitate to contact us immediately).
  • ✅Delay Function: If the device encounters (electric power) voltage fluctuations, it will protect the appliance by providing the output until the voltage stabilizes. The “DELAY” indicator would be turned on to inform its user. The appliance would be delayed for 3 mins to confirm that the voltage is stable so that it could be re-established..
  • ✅Working Principle: As there is an interruption in the current flow, the Voltage surge protector gives an interval of 3 minutes to allow the voltage to stabilize. Additionally, the Voltage surge protector provides protection against voltage spikes that can damage electrical equipment..
  • ✅Adjustable Voltage: The minimum voltage capacity of the protector is adjustable. It can be adjusted from 170V to 265V according to yo....
Check Stock

Valefod 10 Pack DC to DC High Efficiency Voltage Regulator 3.2-35V to 1.25-30V Buck Converter DIY Power Supply Step-Down Module

  • 【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
  • 【Input Voltage】DC 3.2V to 35V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • 【Output Voltage】DC 1.25V to 30V voltage is continuously adjustable, maximum output current is 3A..
  • 【Mini Size】45 * 23 * 14 mm (with potentiometer). 10pcs included..
  • 【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).
Check Stock

SMKAN DP20V2A Constant Voltage Constant Current Programmable Control Step-down Supply Power Module

  • The constant voltage and constant current programmable control power supply module is cabinet and delicate, and it put the collection of analog integration and digital control functions in one. Its adjustable output voltage range is 0-20.0V, step by 0.1V. Its adjustable output current range is 0-2.00A, step by 0.01A. Boot voltages can be stored freely and the model has two groups of quick storage voltage. Compared with the traditional analog power supply, it is more convenient to quickly extract the voltage or current required. LCD display on the model has the function digital voltmeter and ammeter. You can view the preset voltage, input voltage, output voltage, the preset current, output current, output power and LCD brightness..
  • Adjusting preset voltage:Pressing SET button, page down to U-SET, press the codding potentiometer, then enter toadjustnumeric value. Press codding potentiometer in turn to choose the numeric value you want to adjust. Turn codding potentiometer to adjust the numeric value. If you want toexit adjusting voltage, press shortly SET. In the process of adjusting preset voltage, if you open output voltage mode by pressing the ON/OFF, the output voltage will be refreshing by increasing or decreasing the numeric value.
Check Stock

IDEAL INDUSTRIES INC. 61-025 Volt Aware Non-Contact Voltage Tester, Clear and Compact Voltage Testing, CATIV for 1000v

  • ACCURATE VOLTAGE TESTER: Green LED shows unit is active, flashing red indicates live voltage. The VoltAware NCVtester is useful for identifying hot conductors, finding breaks in wires and detecting the presence of AC voltage at outlets, switches, electrical panels, wires and cables..
  • ULTRA EASY TO USE: Twist the tester body to the On position and verify the green light is on. Verify tester operation on a known voltage source. Next, place the tip of the tester near an AC voltage source to obtain a voltage indication. Voltage presence is indicated by a red, flashing light. If no voltage is detected for a period of 15 minutes, the tester will flash green three times then shut off automatically.* Twist the tester body to the Off position, then back to On to reactivate..
  • SLEEK, COMPACT DESIGN: The sleek, non-contact voltage tester designed by the innovative minds at IDEAL. Its compact design makes it ultra easy to use, even in tight spaces and it is packed with features that will help you on the job..
  • BATTERIES INCLUDED: (2) AAA Batteries included with voltage tester. Quick and easy battery replacement — with the tester in the middle position, simply pull apart the two case halves and replace with 2 AAA (LR03) batteries..
Check Stock

uxcell 10Pcs Voltage Dependent Resistors AC 150V 14D241K L8 Radial Lead Disc Varistors

  • Model: 14D241K；Maximum Impulse Current: 4500 A.
  • Maximum continuous working voltage:150 VAC(rms)/V.
  • Maximum continuous working voltage: 200 VDC/V.
  • Maximum limit voltage: 395 VP(8/20μs)/V.
  • Maximum limit voltage and current: 50 IP(8/20μs)/A.
  • Specific epoxy coated disc construction with radial leads, long life use..
Check Stock