Reviews H bridge Motor Driver - BestBuyersPro.com

6Pcs L298N Motor Drive Controller Board DC Dual H-Bridge Stepper Motor Control and Drives Module for Arduino Micro:bit Smart Car Robot UNO MEGA R3 Mega2560

★L298N as main driver chip makes strong driving ability and strong anti-interference,dual-channel h-bridge driver working mode creates higher working efficiency,,drive stepper dc motors to work.to avoid damage the voltage stabilizing chip, please use an external 5v logic supply when using more than 12v.
★Dual-channel H-bridge driver working mode creates higher working efficiency..
★To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
★Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
★L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
Terminal driver part of the supply area VMS: +5V ~ +35V.
Drive part of the peak current Io: 2A / Bridge.
Logical part of the terminal power supply range Vss :4.5-5 .5V.
Logical part of the operating current range: 0 ~ 36mA.
The control signal input voltage range: 4.5-5.5V low 0V high.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..

TB6612 motor driver with 1.2A per channel.
2 full H-bridges means you can drive 2-4 solenoids (only two can be active), two DC motors bi-directionally, or one stepper motor..
Runs at 2.7V-5V logic. The motor & logic voltage are separate..
Good for motor voltages from 4.5V up to 13.5V.

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32....
Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..

Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
The L298P shield DC motor driver has PWM speed control mode.
Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
Stack design can be directly plugged into the Arduino, easier to use..

【1】Package included: 1 x Stepper Motor Driver,1 x Stepper Motor, 1 x Wire..
【2】Suitable for a wide range of stepper motors from NEMA size 17,23 and 24 (42 * 42mm to 60 * 60mm). It can be used in various types of machines, such as XYZ tables, labellers, laser cutters, engraving machines, pick-place devices and so on..
【3】Motor driver: 9V-42V DC power supply, H-bridges bipolar constant phase current drive. The maximum 4.0A of the eight types of output current..
【4】The largest 32 divisions of the 6 models are optional.
Suitable for 4 wires, 6 wires and 8 wires stepper motor..
【5】Protect form: Overheated protection, overcurrent protection, undervoltage protection, prevention of inversion..

Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
Pico Driver Motor HAT is a DC motor control module that is powered by one H-bridge IC L293D with the motor input supply range 6 V-24 V.
Pico Driver Motor HAT is specifically made to work with the Raspberry Pi Pico Board.

H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak).
Completely stackable design: 5 address-select pins means up to 32 stackable shields.
Characteristic: Arduino interface is fully compatible expansion.
Feature: Motors automatically disabled on power-up.