Reviews Drive Shaft Mounting

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2517 1 1/4 Taper Bushing, Sintered Steel, Inch, 1.25\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 5/8 Taper Bushing, Sintered Steel, Inch, 1.63\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

TB Woods 2517 TL25171 Taper Lock Bushing, Cast Iron, Inch, 1\ Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 3020 TL302050MM Taper Lock Bushing, Cast Iron, 50 mm Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 2517 TL2517138 Taper Lock Bushing, Cast Iron, Inch, 1.375\ Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 1008 TL100858 Taper Lock Bushing, Cast Iron, Inch, 0.625\ Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 1108 TL110822MM Taper Lock Bushing, Cast Iron, 22 mm Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock