Reviews Center Support Bearing

Bearing Snatcher Bearing Tool 608 Disassembly Tool & ABEC-9 Bearings 16, Roller Skating Skateboard Accessories…

Material: made of high-quality metal spray paint, not easy to damage, not easy to corrosion, very durable, a good partner for skateboarding..
How to use: Just slide the tool into the center of the bearing and apply a little pressure on the bearing, you can use the tool to remove and replace the 8mm bearing.
It can be used to remove and install 608 wheel bearings of roller skates, it can also only be used for 608 bearings and can be used for roller skates, driftboards .......
Advantages of our bearings ：Our 608 bearings are made of high carbon steel. The ball of the bearing has a problem, it can prevent you and sand from entering and affecting the performance of the bearing. Make your product more outstanding, more handsome and more eye-catching..
The most important thing: we support no-excuse returns, we also have more price advantages than others, so you spend less money and have more fun..

OE Number: 88951975. Please make sure your car model and OE number before ordering.
Durable Material: Made of good material, wear resistant and corrosion resistant. It is not easy to deform after long-term use.
Easy Installation: With mounting hole, you can install the bearing on the driveshaft. The installation saves your time to some extent..
Package Include: 1 x Driveshaft Center Support Bearing.

Price For: Each Surface: Grit-Top Item: Molded Grating Mesh Size: 1-1/2" x 1-1/2" Grating Key: None Bearing Bar Width: 0.25" Bearing Bar Spacing Center-to-Center: 1-1/2" Mesh Pattern: Square Bearing Bar Height: 1" Span: 5 ft. Width: 3 ft. Max. Temp.: 140 Degrees F Depth: 1" Color: Yellow Resin Type: Corvex Country of Origin (subject to change): Multiple.

Fitment: Please check Fitment Filter and Description to see if this item will work on your vehicle before purchase!.
Drive Shaft Center Support Bearing -- Square.
If you have any questions, you can send an email, and we will reply within 24 hours..

Fitment: for Honda CR-V 1997 1998 1999 2000 2001.
OE Number: 40520-S10-003. Please make sure your car model and OE number before ordering.
Durable Material: Made of good material, wear resistant and corrosion resistant. It is not easy to deform after long-term use.
Easy Installation: With mounting hole, you can install the bearing on the driveshaft. The installation saves your time to some extent..
Package Include: 1 x Driveshaft Center Support Bearing.

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Two utility drawers provide ample storage for both work and home needs.
Power center with two AC power outlets and three USB 2.0 connections.
Black paint with a Twelve Step two toned hand rubbed finish with light physical distressing.
Two utility drawers and a drop front keyboard/pencil drawer provide ample storage for both work and home needs.
Full Suspension steel Ball bearing drawer glides provide drawer support and enable a lifetime of smooth operation.
Finished on all sides for placement anywhere in a room.
Leg Assembly Required, Dimensions: 31" W x 28" D x 60" H.

Fitment Notes: Fitment Notes003cbr003e003cbr003eNotes: With Spicer U-Joint Series 1410-1480 Cleveland O55 U-Joint 1.5748" Bearing ID 2.4790" Bearing Centerline To Mounting Surface 4WD003cbr003eQuantity Required:1003cbr003ePart Type: Drive Shaft Center Support.

Quenching Hardness 60 ~ 62 HRC: Conical part is made from T10 steel, quenching hardness 60 to 62 HRC, the main body part is made from high-quality steel, durable to use..
Ultra Precision: High quality bearing design, using high speed bearing for high accuracy. Accuracy is less or equal to .0005..
Application: The primary use of a center is to ensure concentric work is produced.
this allows the workpiece to be transferred between machining operations without any loss of accuracy.Designed for lathe in medium speed and medium load environment. Maximum RPM is 5,000.
High Steel Quality: Well balanced and smooth for effective turning. Ideal to support your work at the tailstock end of your lathe. ust proof seal preventing cutting dust enter into bearing thus prolong service time..
Shipping: This item will ship from USA ,delivery time need about 4-7 days.If there is any questions please feel free to contact with us, our experienced customer service team will response in 24 hours..

LARGE CAPACITY - Industrial wire grid and composite deck can each support 1,500 lb. for a total 3,000 lb. capacity.
POWDER-COATED STEEL - Industrial powder-coated finish on the steel uprights, support straps, and crossbeams won't fade or chip.
STORAGE DRAWER - Measuring 6" tall x 42" wide x 16.5" deep, drawer has ball bearing slides and a 120-pound capacity.
STEEL PEGBOARD - Steel pegboard panel mounts between uprights or on vertical supports and features 1-inch on center spacing.
INCLUDED TOOL HANGERS - Kit includes 6 various pegboard tool hangers to let you store the tools you need within easy reach.