Reviews Arduino Boards - BestBuyersPro.com

Arduino MKR CAN Shield [ASX00005]

Connect an MKR board to a Controller Area Network (CAN) Bus and read/write to/from other devices in the network..
Program your Arduino MKR boards to become CAN peripherals and controllers..
Possible applications: Smart dashboards to existing vehicles, autonomous cars, drones, and industrial machinery..
Use the MKR CAN shield to connect to several types of industrial grade sensors, motors and displays..
Works for any of the Arduino MKR boards, and can be stacked on top of other MKR Shields!.

The Arduino Nano is one of the smallest Arduino boards available on the market.
Tiny form factor, complete, and breadboard-friendly board based on the ATmega328.
Arduino is an open-source hardware, software, and content platform with a worldwide community of over 30 million active users.

【Same function as the original Arduino】It great for learning the basics of how sensors and actuators work, and an essential tool for your rapid prototyping needs.
【CHIP UPGRADE】Upgrade the main control chip to ATMEGA328P-AU.And it same as the original arduino pin layout. It compatible with all expansion boards..
【ADDED A 500MA SELF-RECOVERYFUSE】Compared with the original ARDUINO, a 500ma self-recovery fuse is added, which automatically disconnects the circuit when short-circuited to avoid component damage.Change the plug-in pins of the original ARDUINO to SMD pins to avoid short circuit of the development board contact conductors, which is safer..
【Added 10 LED marquees driven by MOS tubes】which avoids the problem of insufficient output current of the IO port of the single-chip microcomputer, and can directly drive a small DC motor through the IO port..
【EASY TO USE】Change the original USB-B type interface to MICRO-USB interface, which is more convenient to use..

Works with any of the Arduino MKR boards: Zero, WiFi, LoRa, Sigfox, GSM, NBIoT, and Vidor..
Easily connect up to 14 Seeed Studio’s Grove modules to your MKR board..
Ideal for fast projects: plug several modules and go! No soldering required..
Screw terminals to safely connect the carrier board to a power source..
Connect sensors and actuators to the Arduino IoT Cloud and control them remotely!.

ANMBEST Pulsesensor Pulse Heart Rate Sensor is a plug-and-play heart-rate sensor for Arduino and Arduino compatibles..
Pulse Sensor adds amplification and noise cancellation circuitry to the hardware. It's noticeably faster and easier to get reliable pulse readings. The Pulse Sensor works with either a 3V or 5V Arduino..
The sensor can be worn on the finger or earlobe..
Supported development boards are Uno R3, mega2560, leonardo, 51 series, msp430 series, KL25Z. s..
NOTE: This product is NOT a professional medical device and should not be used to diagnose or treat medical conditions..

A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..

★32 pieces double sided PCB prototype boards well packed in a plastic tray which is very easy to store and take out.
★5 different size boards to meet your demands when designing your own Arduino kits, electronic experiments and DIY projects.
★4 mounting holes at the corners of the board are very convenient for installing them together..
★Pre-tinned plated holes on the board make it very handy to solder components and sensors for your projects.
★High quality of durable glass fiber –FR4 material with 1.6mm thickness makes a very solid and sturdy prototype circuit board.

SIM7600A-H 4G HAT is a 4G/3G communication and GNSS positioning module, supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.
Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH series boards, Compatible with Jetson Nano, SIM7600A-H 4G module control pins can connect with host boards like Arduino/STM32.
Supports dial-up, telephone call, SMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. Supports GPS, BeiDou, Glonass, LBS base station positioning.
Connect the 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc..
Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).

Solderless breadboard is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.
Easy to use: the breadboard is made of ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling.
Self-adhesive back tape makes it easy to stick on a platform, like the Arduino prototype shield.
With tight plug-in contacts, the components will sit well after assembly and nothing will wobble..
The jumper wires are easy to insert into the breadboard..

Perfect for Arduino mega sized base board and other programming boards.
Convenient for the prototypes and circuit design experiment and other DIY projects..
Used for electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits..
Standard IC spacing 2.54MM hole plated through among the pad can be perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc..
Electroless Nickel Gold finished prevent the copper on PCB from being oxidized and corroded and is good for soldering and touching..
Made of glass fiber FR-4 material, features high heat resistance, corrosion resistance, mechanical strength, insulation..