Reviews Wire Led Marker Lights

Partsam 20 x 3/4" Round Led Light Trailer Boat Marker Clearance High Low 3SMD Clear Lens, 3/4" round LED combination turn signal running lamp fender lights 3-WIRE assembly Taillights(10Red+10Amber)

  • Package includes 20Pcs(10Pcs Red and 10Pcs Amber) 3/4" Led Marker Lights 3 Wires in Clear Lens, 3 diodes per light, Fix 3/4" Hole.
  • Sealed Light, 3 Wires Setup, High Low Function.
  • 3/4" amber led marker lights 3 wres in clear lens: 3/4" round LED lamp for use as a combination turn signal and running lamp, can be installed anywhere you'd like to mount them by drilling a 3/4" hole in a flat panel. This is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp(one function at a time). It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused.
  • 3/4" red led marker lights 3 wres in clear lens: Clear Lens Red Mini 3/4" Stop Turn Tail Lights 3 LED with Rubber Grommets,very bright for it's size. Dual brightness. install with a rubber mounting grommet and requires a cutout hole of 3/4" diameter. These 3/4" led lights come with 3 wires (white wire ground, black wire is tail light/marker light/clearance light/running light and red wire is for stop and turn functions). This light is DOT approved as your only tail light or turn signal.
  • These high quality LED lamps are DOT-approved for use on your vehicle. Includes pigtail harness and mounting grommet....
Check Stock

Partsam 10X 3.8 Amber 12V Front Side Marker 6 LED Trailer Truck Lorry Indicators Lights, Amber Rear Led Marker Trailer Parking Turn Signal Lights for Truck Bus Boat Rv Lorries SUV UTV

  • Package includes 10 pieces 3.8 Inch Amber Led Trailer Marker Lights 6LED.
  • free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the amber marker lights or to the surface to which the amber light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
  • These small thin clearance lights need to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp).
  • Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx..
  • The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer.
  • Partsam Amber Led Lights function as marker lights, clearance lights, runnling lights, side marker lights, front parking lights, indicator lights, identification lights, boat interior lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps and so on.
  • We also have customers asking whether they can be use as turn signal lights, they can, but they may be not that bright.
  • The side marker indicator light is hardwired with 2 wires and c....
Check Stock

Partsam 30Pcs 3.8

  • 3. When you wire several lights together, you can wire them in parallel.
  • Light Size: 75mm x 20mm x 5mm (2.95″ x 0.8″ x 0.2″), Light Size with Black Base: 96mm x 20mm x 10mm (3.8″ x 0.8″ x 0.4″) and center to center distance: 3-5/16″ approx..
  • Partsam Led Lights function as marker lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps, clearance lights, runnling lights, side marker lights, front parking lights and so on.
  • As every truck lamp come with two wires, they can only use as one function a time.
  • free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the marker lights or to the surface to which the light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
  • These lights don’t come with the on/off switch and Wire leads come out the back in the center so you must drill a hole in the mounting surface for them.
  • 5.These are Waterproof, not submersible. Please do not use it under water.
  • 2. These lights can not be set up to flash as strobes, of course, you can wire to a toggle (on/off) switch to make it come true.
Check Stock

10Pcs 2 Inch Round LED Side Marker Clearance Lights for Trailers, 5 Amber and 5 Red Sealed 2 Round LED Trailer Marker Lights 4 LEDs w/Rubber Grommet Flush Mount 2 Wire Pigtails Truck RV Waterproof

  • This listing features for 5 Pieces red 2 inch round led marker lights and 5 pieces 2 inch amber Round Trailer LED Clearance Marker Lights. These 2 Inch led marker lights are flush mounts to trailer trucks with rubber grommets and standard 2-prong wire pigtails.
  • These 2 round led marker lights include grommets and pigtails for complete installation.
  • Each 2 inch round trailer marker light come with 4 LEDs, providing you better visability when driving on road.
  • Sonically sealed, IP65 waterproof housing and lens unit is submersible.
  • Wiring tips: Each 2 inch round trailer side marker lights includes a standard 2 prong wire pigtails: White is the negative and black is the positive. Dimensions: Outer Diameter: 2.5"in., Inner Diameter: 2"in., High w/ Grommet: 1in.(depends how in you press the lights) , you may need to drill a hole about 2-5/16" to install.
  • These 2 Round LED Light Side Marker Clearance lights are universal for almost all 12v dc vehicles like Truck, Trailers,Pick Up,UTE, UTV etc. Note: So these 2 round led lights can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, please install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side mar....
Check Stock

Partsam Thin Line 3.8" 6 LED Blue Side Led Trailer Marker Lights Sealed Clearance Light Indicators for Trucks Bus Trailer RV Camper Lorry Van UTV Marine Boat Stern Light Decoration Lights(10Pack)

  • Package includes 10 pieces 3.8 Inch Blue Led Trailer Marker Lights 6LED.
  • free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the blue marker lights or to the surface to which the blue light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
  • These small thin clearance lights need to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp).
  • Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx..
  • The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer.
  • Partsam blue led lights function as marker lights, clearance lights, runnling lights, side marker lights, license plate lights, indicator lights, identification lights, boat interior lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light,cockpit light, step lights, deck lights, trailer lights, led courtesy lights, stern light, stair lights, truck lamps and so on.
  • Truly many customers use them as boat marine lights, very bright.
  • The blue led strip light bar is hardwired with 2 w....
Check Stock

BJZ LED Trailer Marker Lights Amber 6 Led Side Marker Clearance Light Bar 12V 3.8" Front Rear Signal Indicator Smoked Light Strip Waterproof for Trailer Truck Van Pickup ATV UTV RV, 10Pcs

  • ✔【Amber LED Side Light Bar Parameters】Pack of 10, each marker light with PC smoked lens, built-in 6 high-brightness LEDs, with ABS black base. Waterproof: IP67.
  • ✔【Wide Application of LED Marker Lights】Fit for LED marker lights, side marker lights, trailer marker lights, clearance lights, indicator lights, tail lights, running lights, turn signal lights, brake lights, parking lights, grille lights, decorative lights, fog lights, undeglow lights and more..
  • ✔【Applicable Models of LED Side Lights】Suitable for Truck, Trailer, Pickup, ATV, UTV, RV, SUV, Van, Offroad, Golf Cart, Bus, Motorcycle, Snowmobile, F350, F450, Lorry, Camper, etc..
  • ✔【High quality Clearance Lights】External reinforced PC lens and scratch resistant ABS base with high brightness SMD LED wick inside. IP67 sealed waterproof, dustproof, shockproof, durable, and not easy to fade after long-term exposure. LED lights can output high-brightness light with very low power consumption, improving your safety when driving at night..
  • ✔【Easy to Install】Surface mount, mounting hole distance is 3.34 inches (85mm). 2-wire connection: Red is Posi....
Check Stock

Partsam 2pcs 6" Amber LED Rectangle Tail Stop Marker Light Trailer Truck RV 3 Wires 21LED, 6x2 Rectangular Led Clearance Lights, 2x6 Big Side Marker Lights

  • Package includes 2 Pieces 2x6 inch Amber Rectangular Trailer Marker Led Lights 3 Wires Surface Mount, 21 Led diodes per amber light.
  • Sealed amber led Light, 3 Wires Setup, High Low Function. Other accessories are not included.
  • Compared with those similar side marker lights on market which can be used as led marker light only, this 6 inch rectangle LED lamp is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp simultaneously. It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These are a really popular style thanks to their multi-faceted design.
  • Size: 6" x 2" x 1.4" approx. and hole to hole distance: 4.8". Dim Function draws 20 mA & Bright Function draws 110 mA approx.. This trailer clearance light is unversal for almost all 12V vehicles as well as the size fits.
  • This amber marker lights is HARDWIRED with 3 wires: Black is ground, white is low brightness as marker lights, clearance lights or running lights, red is high brightness as turn signal lights.
  • Commonly known as a trailer light, these 2" x 6" rectangular trailer lights can really be installed anywhere you'd like to surface mount them. It is going to fit perfectly on....
Check Stock

Partsam Rectangle 14x Amber/Red 4" Truck Boat Trailer Side Marker Indicator lights 8-LED Surface Mount

  • Package includes 14 Pieces (7Red+7Amber) Universal 4 Inch Led Side Marker Indicator Lights. NOTE: This marker lights set includes standard nut and bolt for anchoring, not self tapping screws(bot specs: 0.3cm diameter and 2.6CM long). You may need to drill new mounting holes all the way through, then use the bolt and nut to install.
  • 7 Pieces Red Led Marker Lights and 7 Pieces Amber Led Marker Lights.
  • Light Size: 4" x 1.6" x 0.7" and Mounting holes spacing: 3.15in. approx.,operates form 9-16Volts.
  • Each Clearance Light is built in 8 LEDs miro reflectors, provide you super night visability on the road.
  • HARDWIRED WITH TWO WIRES: BLACK IS GROUND, YELLOW IS POSITIVE.
  • This Rectangle led trailer light is surface mount and you can mount anywhere as long as the size fit.
  • Usage: side marker lights, roof lights, corner lights, rear lights, identification lights fender lights,cab lights, clearance lights etc. Note: this led marker lights only come with one positive wire, one functions at a time. If you use it as the front turn signal lights, it may not be that bright, thanks.
  • Application: Works on any 12V DC vehicles. Perfectly suitable for all kinds of trucks, Trailer, Semi-trailer, Lorry, Off-road vehicle, ATV, SUV, UTE, Pickup, Tractor, Bus, Car, Boat, Car....
Check Stock

10Pcs 2 Inch Round Led Marker Lights, 2 Inch Round Trailer LED Side Marker and Clearance Marker Lights 4 LED Sealed Flush Mount with Rubber Grommets and 2 Prong Wire Pigtails Waterproof (5Red+5Amber)

  • This listing features for 5 Pieces 2 Inch round amber led marker lights and 5 Pieces 2 Inch round red led marker lights. These 2 Inch led marker lights are flush mounts to trailer trucks with rubber grommets and standard 2-prong wire pigtails.
  • These 2 round led marker lights include grommets and pigtails for complete installation.
  • Each 2 inch round trailer marker light come with 4 LEDs, providing you better visability when driving on road.
  • Sonically sealed, IP67 waterproof housing and lens unit is submersible.
  • Wiring tips: Each 2 inch round trailer side marker lights includes a standard 2 prong wire pigtails: Black is the negative and red is the positive. Dimensions: Outer Diameter: 2.5"in., Inner Diameter: 2"in., High w/ Grommet: 1in.(depends how in you press the lights) , you may need to drill a hole about 2-5/16" to install.
  • These 2 inch round led trailer clearance lights are universal for almost all 12v dc vehicles, such as Semi Truck Trailers, Utility Truck, Horse Trailer, Utility Trailer, Pick Up Truck, UTE, UTV etc. Note: So these 2 round led lights can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, please install 2 separate lights on your trailer - one as a front or rear....
Check Stock

Partsam Pair 6\ Amber Side Front Marker Light Turn Signal Light High Low Brightness Sealed, 20 Diodes, Trailer Clearance and led marker lights, 6x2 Rectangular Rectangle led lights, 3 Wires

  • Package includes 2 Pieces 2" x 6" Rectangular Trailer Marker LED Lights 3 Wires in Clear Lens, 20 Led diodes per light.
  • Sealed Light, 3 Wires Setup, High Low Function. Other accessories are not included.
  • 6" amber led marker lights 3 wres in clear lens: 6 inch rectangle LED lamp for use as a combination turn signal lights and running lamps, can be installed anywhere you'd like to surface mount them. This is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp simultaneously. It can also be used as only a marker light (or only an auxiliary turn signal light) by using two wires and leaving the third wire unused.
  • Hardwired with 3 wires: White is ground, black is low brightness as marker lights or running lights, red is high brightness as turn signal lights.
  • Size: 6" x 2" x 1.4" approx. and hole to hole distance: 4.8".
  • These 2x6 led trailer lights are universal for almost all 12V DC vehicles like truck trailers Motorhome or heavy trucks like peterbilt, kenworth, freightliner etc. You can found on road people use them for kenworth bumper lights, car aux turn signals, Motorhome turn signal lights and son on. Note: This 2x6 rectangular marker light is generally waterproof, please do not use it in hea....
Check Stock