Reviews Water Pump Inlet Tube

Comet ZWD 4040G Pressure Washer Pump 4 GPM 4000 PSI For 1\ Hollow Shaft Engines (Fully Plumbed with Unloader External Bypass)

  • 2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
  • Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6 3/16” x 6 7/16” & 4" Center to Each Outer Hole. Maximum Water Temperature: 140° F. Inlet Connection Type: Standard Garden Hose. Outlet Tube Connection: 22mm Male. Refer to images 2 and 3 for more information.
  • Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
  • This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI. Pump head can be flipped.
  • This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine or can't reach the under side of frame such as the engine has a longer shaft. If spacers aren't used when installing, the pump legs will break from stress.
Check Stock

mistcooling High Pressure Misting System 1500 PSI - Flexible (60 Feet - 20 Nozzles)

  • Features: Base 20 Nozzle Kit Contains: - 1 - Max1500 psi High pressure pump with built-in water on/off valve, low water cut off switch, pressure bypass, commercial 5-micron filtration, Outdoor Rust Proof Enclosure with on/off Switch.
  • - 60ft 1/4" Nylon Tubing-Black - 20 - HP Push Lock Misting Tees.
  • - 20- Stainless Steel Orifice Nozzles (0.006") - 1 - Push Lock End Plug - 2- Nozzle plugs - 2- Replacement Nozzles - 1- Drain Valve Assembly - Stainless Steel Mounting Clamps.
  • Specs:1500 PSI Misting Pump: 0.15 & 0.30 GPM - For up to 40 Misting Nozzles - Pressure Adjustment Valve to allow increase or decrease of the outlet water pressure. - Pump pre-set for ideal working - Solenoid Valve – controls flow of water in the misting pump - Pressure Switch or no cut off water switch will turn pump off, if no water supply - Thermal Safety Swithc - Maximum Speed 1800 rpm - Full load Amps. (0.15/ 0.30 gpm.) 1.38/ 2.00 Amps - Noise level: 75 DB - Maximum Inlet Pressure–100psi.
  • Filter: - 5 Micron Filter - Filter in the package comes with 3/8 inch inlet- outlet fitting. - Standard pump comes with ¼ inch push lock type fitting.
  • However, it is placed on 3/8 inch male and ¼ inch female adapter. - Outlet comes with ¼ inch fitting as standard.
Check Stock

12v 80w Electric Oil Change Transfer Pump Extractor Kits for Boat/Car/Lawn Mower Marine/Jet Ski/Truck/RV/ATV Changing Diesel Fluid Scavenge Suction

  • 80w OIL CHANGE EXTRACTOR - The engine oil transfer pump is 80w. Extracting motor oil from vehicles quickly and cleanly. It can be used for changing oil 3L/min. Not compatible with water and petrol, gasoline, kerosene..
  • EASY ENGINE OIL CHANGE - The 12v oil extractor pump comes with 2 extractor tubes, easy for a top down oil change by single ON/OFF switch controll. Pumps oil out throw dip stick, no need to lay under the machines or vehicles. The oil will simply draw out the motor through the oil dipstick bore..
  • MULTIFUNCTIONAL OIL EXTRACTOR PUMP - The oil change pump kit fits for Car, Boat, Jet ski, Motorcycle, Scooter, Marine, Quad Bike, Truck, Forklift, Generator, Tractor, Riding Mower, Snowmower, etc, siphoning & transfering diesel, oil to other Cars, Trucks, Ships, Boats, Tractors, Farm Machinery, Plant Equipment Etc..
  • PORTABLE OIL PUMP CHANGE EXTRACTOR - The oil transfer pump is mini but powerful. With 5ft Outlet tube & 4ft Inlet tube, the 8.2ft long battery clamps makes the extractor pump kit possible for being used at large range. The 2 hoops are used to tighten the tubes to avoid oil spilling..
  • FOR DIFFERENTIAL FLUID TRANSMISSION - This high efficient self-priming oil extractor pump is easy to pump various fluids and oils. Place the inlet/outlet ho....
Check Stock

Troy Bilt Complete Pump Head Assy for RMW and SRMW Pumps AR42518

  • ...s pump features a maintenance-free crankcase so you never have to change the oil. It is manufactured from fully anodized die-cast aluminum for protection against corrosion.
  • Extended durability: A Thermal Relief Valve (TRV) protects the pump from overheating while in bypass mode. The TRV releases small amounts of hot water and intakes cooler water to prevent overheating and extend the life of the pump.
  • Get the right pump for your machine: this pump is designed for gas-powered pressure washers with horizontal engines. Its SAE bolt pattern, hardware, and standard connections make it a great fit for many brands and models of power washers.
Check Stock

The ROP Shop | 2400 PSI Power Pressure Washer Water Pump for Excell & Devilbiss VR2400, VR2500

  • The ROP Shop replacement 2400 PSI Power Pressure Washer Water Pump for Excell & Devilbiss VR2400, VR2500.
  • Specs - Maximum Pressure: 2400 PSI. Maximum Flow: 2.4 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8". 3 Bolt Pattern: 7 11/16” x 6 3/16” x 6 7/16” & 4" Center to Each Outer Hole. Maximum Water Temperature: 140° F. Inlet Connection Type: Standard Garden Hose. Outlet Tube Connection: 22mm Male. Refer to images 2 and 3 for more information.
  • Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube (come installed).
  • This pump is for vertical gas engine driven units. In some instances, the pump may need to be removed to change engine oil. The mounting flange provides a convenient connection to most 7/8” diameter shaft vertical gas engines in 4.5-7 HP. The pump has a hole in the leg for draining the engine oil. The pump includes a built-in pressure control valve, downstream chemical injection system and thermal relief valve.
Check Stock

BOYISEN Oil Change Pump Extractor 12v 60W Oil Extractor Pump Diesel Fluid Transfer Scavenge Suction Pump Oil Quick Changer for Car, Boat, Marine, Motorbike, Truck, RV, ATV(Yellow)

  • ...an oil changing and transfer, all parameter is verified by multiple test. Diesel Flow Rate: 1.5L/min, Engine Oil Flow Rate(40-60℃): 0.3L/min, Inlet Tube Length: 1.2m/47.2in, Outlet Tube Length: 1.4m/55.1in, Voltage: 12V, maximum current: 5A, maximum power: 60W.
  • 【NOTES】A, This oil transfer pump CAN NOT transfer WATER, GASOLINE, PETROL, FUEL or FLAMMABLE LIQUID. B, Please DO NOT misplace the direction of import and export, positive and negative poles and secure the hose clamps. C, Heat up your engine oil to 104°F-140°F before pumping D, We tested oil pump before shipping, there might be little oil stain in the pump, kindly understand. E, To make it last longer, it’s recommended to keep a little oil inside when the extractor pump is not in use..
  • 【Premium Quality】The quality of oil change pump extractor varies widely. We are using pure copper for the motor and alligator. Good electrical conductivity, corrosion resistance and rust free, effectively avoid leakage or short circuit. Overheat protection will cut off the power supply automatically for safety.
  • 【What You Get】The diesel change pump come with 2 outlet hose, 2 inlet hose, 4 hose locks and 2 battery clips. A screw driver would help you to secure the hose clips easily, ensure a smooth ....
Check Stock

BOYISEN Oil Change Pump Extractor 12v 80W Oil Extractor Pump Diesel Fluid Transfer Scavenge Suction Pump Oil Quick Changer for Car, Boat, Marine, Motorbike, Truck, RV, ATV(Orange)

  • ...an oil changing and transfer, all parameter is verified by multiple test. Diesel Flow Rate: 1.5L/min, Engine Oil Flow Rate(40-60℃): 0.3L/min, Inlet Tube Length: 1.2m/47.2in, Outlet Tube Length: 1.4m/55.1in, Voltage: 12V, maximum current: 7A, maximum power: 80W.
  • 【NOTES】A, This oil transfer pump CAN NOT transfer WATER, GASOLINE, PETROL, FUEL or FLAMMABLE LIQUID. B, Please DO NOT misplace the direction of import and export, positive and negative poles and secure the hose clamps. C, Heat up your engine oil to 104°F-140°F before pumping. D, We tested oil pump before shipping, there might be little oil stain in the pump, kindly understand. E, To make it last longer, it’s recommended to keep a little oil inside when the extractor pump is not in use.
  • 【Premium Quality】The quality of oil change pump extractor varies widely. We are using pure copper for the motor and alligator. Good electrical conductivity, corrosion resistance and rust free, effectively avoid leakage or short circuit.
  • 【What You Get】The diesel change pump come with 2 outlet hose, 2 inlet hose, 4 hose locks and 2 battery clips. The hose clip enable to thoroughly seal the connection and prevent leaking. A screw driver would help you to secure the hose clips easily, ensure a smooth ....
Check Stock

mistcooling 250 PSI Misting Pump

  • 250 psi pump quiet operation 35Db solenoid valve – Controls flow of water in the pump in built filter – helps protect your misting nozzles built in water by pass self-priming.
  • Nickel-plated brass button series With stainless-steel Orifice Standard 10/24-inch thread 0. 012-inch Orifice Rust-resistant fixed impeller pin 0. 014 GPM Flow per Nozzle.
  • Maximum inlet pressure: 100 psi Minimum inlet pressure: self- priming. Maximum outlet pressure: 250 psi (depends on line length and numbers of nozzles) maximum flow: 0. 9 GPM full load Amps. 110V AC: 0. 7 amps 12V DC: 4. 0 amps Voltage: 110V-220V AC/ 12V DC (refer manufacturing label on the pump) noise level: 40 dB. Maximum fluid temperature: for room temperature/ cold water applications only.
  • Max pressure 250 psi Available in 110 V, 220 V & 12 VDC Durable Rust Proof Enclosure Thermal Safety Switch Oil-less Pumps may generate heat, motor manufacturer have installed built-in thermal safety switch to improve the longevity of pumps Standard pump inlet: 3/8-inch push lock Fitting. Standard Pump outlet: ¼ inch Push-lock fitting. Max pressure 250 psi 110 V AC.
  • 1. Solenoid Valve Solenoid valve controls the flow of the water in to the pump. You may leave the inlet water source on at all the time. Water will enter th....
Check Stock

PEGGAS 7/8\ Shaft Vertical Pressure Washer Pump - 3000 PSI @ 2.5 GPM OEM & Replacement Pump for Power Washer Compatible with 308653045, 308653093, 308653052, 308653078, GCV190, and more

  • ...s pump features a maintenance-free crankcase so you never have to change the oil. It is manufactured from fully anodized die-cast aluminum for protection against corrosion.
  • Extended durability: A Thermal Relief Valve (TRV) protects the pump from overheating while in bypass mode. The TRV releases small amounts of hot water and intakes cooler water to prevent overheating and extend the life of the pump.
  • Get the right pump for your machine: this pump is designed for gas-powered pressure washers with vertical engines. Its SAE bolt pattern, hardware, and standard connections make it a great fit for many brands and models of power washers.
Check Stock

Danner Manufacturing, Inc. DNR02750 Pondmaster Pond-Mag, Magnetic Drive Water Pump, 2400 GPH, 02750, Black

  • Please refer user manual under product description..
  • Provide the best environment for your aquatic life with Danner products.
  • Magnetic-driven, epoxy-encapsulated, oil-free motor.
  • consumes ½ the energy (240 watts) comparable pumps.
  • 1-inch female national pipe thread inlet 1-inch or 1-1/4-inch flex tube male outlet.
Check Stock