Reviews Vertical Shaft Kiln

King David 16WPCK 16-Inch Pear Cork Handle Conducting Baton

  • The shafts are made of the finest straight grain birch and maple - kiln dried to prevent warp.
  • The white high luster coating is heat set to provide long service and lasting beauty.
Check Stock

DLE Engines 30-C28#3 DLE30 Electronic Ignition

  • 【PROFESSIONAL DIESEL ENGINE】4-stroke Air- Cooled Diesel Engine.Through advanced software analysis and optimization design, the reliability of....
  • 【DIESEL ENGINE SPECIFICATIONS】Model：186F Туре：Single-cylinder, vertical, 4-stroke air- cooled diesel engine Combustion system：Direct....
  • 【DIESEL ENGINE PARAMETER】Oil System: Pressure and Splash Engine Cooling Type: Forced Air Cooling.
  • 【SHAFT PARAMETER 】 Shaft Type: Keyed - Straight Shaft Diameter: 1" Diameter, 1/4" Keyway Shaft Length: 72.2mm (2-5/6" Length) Shaft I.D. Thread....
  • 【WIDE APPLICATION】It is widely used in small agricultural machinery, such as micro-tiller, pastoral management machine, irrigation and drainage....
Check Stock

Playcraft Telluride Espresso 22’ Shuffleboard Table

  • 3” – vertical stave, edge glued, kiln dried Russian Birch butcher block playfield with ¼” poured polymer surface.
  • 24” stained hardwood overhead electronic scorer with plexi face.
  • Playing equipment includes, set of (8) 2-5/16” weights – 4 blue, 4 red, board sweep, speed wax and playing instructions.
Check Stock

Karcher 9.120-021.0 Axial Pressure Washer Pump 2.5GPM 3000PSI 3/4 Horizontal Shaft

  • Common Bolt Pattern For GC & GX Engines With 3/4" Shaft.
Check Stock

Martin SH 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.871\ OD, 1.31\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

The Bundling Off L116T Light and 2m ac Adapter

  • 2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
  • Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6....
  • Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
  • This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI.....
  • This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine....
Check Stock

Martin SDS 2 Quick Disconnect Bushing, Ductile Iron, Inch, 2\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 0.43\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 7/8 Quick Disconnect Bushing, Sintered Steel, Inch, 0.87\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock