Reviews Ttl Module

Geekstory BN-880 GPS Module U8 with Flash HMC5883L Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller

• BN-880 is suitable for Open source flight controller, not for flight control with SCM.
• Bn 880 gps module is dual module compass, with and electronic compass IC HMC5883L.
• Bn 880 gps module has flash to save configuration. So you do not need to reset next time when you use it.
• DIts data Level is TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
• When you use it for Raspberry Pi, there is no driver needed but you need to install software.

DIYmalls BN-180 GPS Module TTL Dual Glonass GPS + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D Betaflight Flight Control

• BN180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to....
• When you power up bn 180 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold....
• Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
• BN 180 gps doesn't have flash and compass. If you need it, please buy bn-880 gps module via "Visit the DIYmalls Store".
• If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page,....

Juried Engineering LM339N LM339 Quad Differential Comparator Industrial Grade Breadboard-Friendly IC DIP-14 (Pack of 5)

• SINGLE-CHANNEL: TLV3501 is a single-channel high-speed push-pull output comparator, delay is 4.5ns, supply voltage: + 2.7V to + 5.5V.
• FRONT SHAPING MODULE: This module can be for a wide range of voltage signal shaping period, as the frequency, phase difference time domain measurements and other front-end conditioning module.
• CMOS AND TTL: Rail-to-rail output can directly drive a CMOS or TTL logic.
• EASY TO OPERATE: Without threshold setting, the sine wave, square wave and triangular wave can be transformed into square wave, which can be used easily without debugging.
• GREAT EXTENSIBILITY: At the same time, it has great extensibility, just change a small amount of the original.

Maikrt Embedded QR Code Scanning Module USB and UART Serial Port Barcode Scanner Identification Module Bar Code Reader for Access Control, Locker Scan Code Payment etc

• A small 1D/2D codes reader,Can be embedded in any device for scanning code to identify other items, by using the intelligent image recognition algorithm.Configurable via scanning 'configuration code',Module matching light source, Can work in the dark..
• Embedded QR code scanning module is used for access control, channel gate, locker, scan code payment, etc. And other industry equipment to achieve smart project,The performance is stable and the decoding speed is very fast..
• 2D/QR code scanning module support linux,Android, windows and other systems, Can easily capture bar codes 1D, 2D on labels, paper, and mobile phone or computer displays,Sensitive and accurately..
• USB and TTL dual interface, equipped with 9pin terminal line and USB cable, which is convenient for you to convert between UART TTL serial port and USB interface. No need to worry about the use of interface types..
• After receiving our products, connect to the line, after power-on That can scan the code.
• The module scans the code directly and sends the result to your host computer automatically. After receiving the data, the host computer can proceed to the next step..

ACEIRMC 3pcs W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5

• Power supply mode:3.3V external power supply, current should be more than 200mA.
• USR-ES1 is the Ethernet module of a SPI interface, interface is TTL level of 3.3V, power supply voltage of +3.3V, please ensure that the current is not less than 200mA, voltage is continuous and stable +3.3V..
• W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5.
• Control interface:The TTL level, 3.3V SPI interface.

DaFuRui 5PCS MAX3232 RS232 to TTL Converter 3.3V to 5V DB9 Female RS232 Serial Prot to TTL Converter Module Root Connector for Equipment Upgrades Like DVD

• ★MAX3232 3.3V to 5V DB9 Male RS232 Serial Prot to TTL Converter Module..
• ★Program the type of microcontroller: STC/STM32 / NXP / Renesas MCU / NEC..
• ★Used in radio modification,mobile phone brushing,XBOX360 brushing machine,GPS,DVD brushing, hard disk repair,set-top box upgrade..
• ★Package Include:5PCS x MAX3232 RS232 to TTL Serial Port Converter Module and 20pcs Dupont Lines..

Development Board Module Kit Fit for 850/900/1800/1900 MHz GPRS/GSM Antenna, 5~26V

• Computer debugging USB--TTL. This module is powered by: 5V-26V, 5V 2A power supply is recommended. After plugging in the motherboard, the power supply must be able to supply 2A. The reason is that the GPRS Shield startup current and the maximum top current required to work up to 2A, but the USB port can not provide such a large current, so the external power supply equipment must be provided..
• The other power supply port leads to the 3.7--4.5V power supply for lithium battery power supply. The serial port is perfectly compatible. The TTL serial port is compatible with 3.3 and 5V microcontrollers..
• Make sure your SIM card is not locked. The best baud rate for GPRS Shield communication is 19200 BPS 8-n-1 (GPRS Shield automatically matches baud rate by default). Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world..

ACEIRMC 4pcs AT-09 Bluetooth 4.0 Transceiver BLE Module Serial Port CC2541 HM-10 MLT-BT05

• The AT-09 is a module that contains a BLE chip (CC2541)..
• This small size Bluetooth 4.0 TTL transceiver module allows your target device communicate with for iPhone/iPAD, IOS 6 or Android 4.3 above devices..
• This module allows to perform serial communication with the BLE chip thanks to an Rx and a Tx pin..
• When the Bluetooth connection is not established, the baud rate, name, and pairing password can be set by the AT command. After the setting, the parameter is saved after power-off, and the Bluetooth connection automatically switches to the transparent transmission mode..
• The module is also very similar to the HM-10 module and is also compatible with it so if you have some experience with the latter, you will get started quickly with the AT-09..

HiLetgo 2pcs CP2102 MICRO USB to UART TTL Module 6 Pin Serial Converter STC Replace FT232

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

• ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
• ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
• ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
• ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
• ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..