Reviews Tft Vanity

DIYmall Mini PiTFT 1.3″ LCD Display 240×240 TFT Add-on for Raspberry Pi 3.3V SPI ST7789 3.3V SPI ST7789 Full Color

  • TFT size： 1.3″ diagonal, Voltage：3.3V, Interface：SPI, Driver: ST7789, Color：Full color.
  • The Mini Pi TFT 1.3 ” – 240×240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi , to give you a little display..
  • The Mini Pi TFT comes with a full color 240×240 pixel IPS display with great visibility at all angles..
  • The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It’s also nice and compact so it will fit into any case..
Check Stock

DIYmall Mini PiTFT 1.3″ LCD Display 240×240 TFT Add-on for Raspberry Pi 3.3V SPI ST7789 3.3V SPI ST7789 Full Color(Pack of 2PCS)

  • TFT size： 1.3″ diagonal, Voltage：3.3V, Interface：SPI, Driver: ST7789, Color：Full color.
  • The Mini Pi TFT 1.3 ” – 240×240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi , to give you a little display..
  • The Mini Pi TFT comes with a full color 240×240 pixel IPS display with great visibility at all angles..
  • The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It’s also nice and compact so it will fit into any case..
Check Stock

BIGTREETECH SKR Mini E3 V3.0 Control Board Integrated TMC2209 UART Stepper Driver Supports Marlin/Klipper Compatible Ender 3/Ender 3 Pro/Ender 3 V2 3D Printer Motherboard ZZB000590 Black

  • ⭐【Main Control Chip】BIGTREETECH SKR Mini E3 V3.0 control board adoptes the G0 series MCU-STM32G0B1RET6 or STM32G0B0RET6 ARM Coretex. integrated TMC2209 Silent stepper motor drive,Support runing Klipper&Marlin..
  • ⭐【Heat Sink Design Upgrade】New upgraded to integrated large stepping motor driver aluminum heat sink,strengthen the drive heat dissipation capacity, and greatly improve the motherboardc heat dissipation performance..
  • ⭐【Multiple Functions】It Supports BLTouch, RGB lights,Filament detection, Automatic shutdown,power-off reesume, Display supports TFT35 E3 V3.0.1/TFT35 V3.0.1/TFT28/TFT43/TFT50/TFT70 V3.0 touch screen as well as original 12864 LCD of Ender 3 printer..
  • ⭐【Fan Upgraded】Increase Three CNC heat dissipation controllable fan interface to reduce the printer temperature when the device is working..
  • ⭐【Multiple Compatibile】BIGTREETECH SKR MINI E3 V3.0 Control board is design for Ender 3,plug and play,compatible with Ender V2 Ender 3/ende 3 pro/ender 5/ender 5 pro/CR-10 3D printer, the firmware is pre-install well before we ship out, you can select the firmware base on your needs..
Check Stock

Ferwooh Nextion 3.5'' Display NX4832T035 Resistive Touch Screen HMI TFT Smart Module LCD for Arduino Raspberry Pi ESP8266

  • The 3.2 tft lcd expansion board is compatible with arduino mega 2560.
  • With tft lcd shield, you can use 3.2 touch screen with mega more conveniently.
  • This 3.2" lcd shield is NOT compatible with all 3.2" tft lcd. Please chheck it carefully..
  • You can buy 3.2" tft lcd for the shield by "Visit the DIYmalls Store".
  • If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question"..
Check Stock

DIYmalls ILI9341 3.2 inch TFT LCD Display Screen Module 3.3V Resistive Touch Panel 320x240 w/SD Card Slot for Mega 2560 only

  • ILI9341 tft display has 40 pins, so it is not compatible with uno r3 and nano..
  • ILI9341 display works at 3.3V. If you use it with mega 2560, please insert TFT 3.2 shield, not directly connect board with tft lcd module..
  • You may need to set a suitable parameter in sketches to use this 3.2" touch screen, but it is not a difficult task..
  • If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question"..
  • ili9341 3.2 inch tft lcd can not work with esp32 board due to no SPI interface..
Check Stock

sb components 3.2\ TFT LCD Transparent Case for Raspberry Pi 2 and Raspberry Pi 3 (Black)

  • This is a no-nonsense protective case for 3.2" TFT LCD for Raspberry Pi 3 Model B.
  • The case is a three-piece injection-moulded ABS enclosure that snaps together around 3.2" TFT LCD and Raspberry Pi 2.
  • It provides the best available protection/accessibility for 3.2" TFT LCD and Raspberry Pi 2 Model B.
  • Wall Mountable. Access to all Pi 2 consumer ports..
Check Stock

Ickiya MKS Gen L V2.1 3D Printer Control Board Motherboard, Open Source Marlin Support TMC2209/TMC2208/TMC2208/TFT35 V3.0/TFT35 E3/BL TOUCH/LCD12684 for Ramps 1.4 /Ramps 1.5/Ramps 1.6 3D Printer

  • ✅Integrate 2560 and ramps1.4 are intergrated on a piece of board, which solves the problem of complicated and easy failure for Ramps1.4 composite interface.Users can change their own motor drive, support A4988/TMC2209/TMC2208/TMC5160/DRV8825 stepper drivers.
  • ✅Using CH340 serial chip to ensure the stable and reliable premise, reduce the cost, and to solve the problem of the previous 16U2 hard drive.Using the open source firmware for Marlin, the configuration is exactly the same as for ramps1.4, and can replace for Ramps1.4 directly..
  • ✅24V input can be accepted, and the same system power can reduce the hot bed current to 1/4, effectively solving the hot bed MOS tube heating problem..
  • ✅It can be directly connected to 2004LCD display and 12864LCD display, and can be supported by TFT28 /TFT32/TFT35/TFT50/TFT70 touch screen..
  • ✅The XYZ axis adopts the terminals of different colors to correspond to the motor and the limit switch, and the connection is convenient,reduces the probability of inserting and reversing, and prevents the main board from being damage by the oppsite inserted of the drive..
Check Stock

3.5 inch TFT LCD Display Screen, 320x240 Resolution Compatible Display Module, LCD Display Screen 54pin

  • 【HIGH QUALITY】▶RGB LCD Display Screen is 100% brand new and high quality..
  • 【DISPLAY SCREEN】▶This product is 3.5inch TFT LCD display screen, with resolution of 320RGB x 240..
  • 【COMPATIBLE】▶This TFT LCD display is compatible with LQ035NC111 54pin LCD..
  • 【THREE MODES】▶The TFT LCD screen has 3 kinds display mode: TN, Normally White, and Transmissive..
  • 【INTERFACE】▶Signal interface digital RGB (8/24-bit) + Serial Peripheral Interface, CCIR601/656 , 54 pins , FPC..
Check Stock

NEXTION 7 inch Enhanced NX8048K070-011C HMI Touch Screen LCD Display Pannel 800x480 with Enclosure Case for Arduino Raspberry Pi (Capacitive)

  • Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or device, it is the best solution to replace traditional LCD and LED. Replace the Nixie tube. It is mainly used in the Internet of Things (IoT) or consumer electronics..
  • Nextion consists of a hardware part (a series of TFT cards) and a software part (the Nextion editor). The Nextion TFT board uses only one serial port for communication. Save users the hassle of wiring. It is easy to adapt the Nextion family HMI to existing projects. Users just need to provide it with a UART..
  • You can power Nextion 3.5 from the 5V pin on the microcontroller, but this is not recommended. Working with insufficient power can damage the screen, so please use the power board that comes with nextion. See the image for use..
  • NX4832T035 is a powerful 3.5 inch HMI. Features include: 3.5 inch 480 x 320 TFT resistive touchscreen display, 16MB Flash, 2KB RAM, 65,000 colors. Viewing area: 73.44mm (L) × 48.96mm (W).
  • Uploading a TFT file via an SD card is faster than a 4-pin serial connection, but the credit card is in FAT32 format and does not exceed 32GB..
Check Stock

BIGTREETECH TFT35 E3 V3.0.1 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR Mini E3 SKR E3 DIP Board for Ender 3 CR10 3D Printer

  • ...pearance size: 93*87mm, power input : 5V. This is a 3.5 inch full-color screen with ultra clear interface and responsive touch, it is designed for ender 3 3d printer especially, which can be a drop-in replacement for its original LCD screen..
  • ❤【Two Working Modes】TFT35 E3 V3.0.1 touch screen support UART serial port screen mode (touch screen mode) and 12864 screen mode, it can replace original display of Ender 3 3D printer. You can enjoy two printing modes: SD card and U disk..
  • ❤【More Extension Ports is Reserved】TFT35 E3 V3.0.1 display r eserve the extension port of filament breaking detection,automatic shutdown after printing,also WIFI function can be realized by external WIFI module through WIFI port..
  • ❤【Firmware Update】 TFT35 E3 V3.0.1 is easy and convenient to update firmware by SD card,download from our github, copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated..
  • ❤【Quality Warranty 】TFT35 E3 V3.0.1 touch screen is designed and produced by BIGTREETECH team,any qu....
Check Stock