Reviews Stepper Motor Wire Connector

CenryKay 5pcs ULN2003 28BYJ-48 4-Phase Stepper Motor with 5V Drive Board and 10pcs Dupont Wire Male to Female Breadboard Jumper Wires Compatible with Arduino

A, B, C, D four-phase LED indicates the status of the stepper motor work..
Stepper motor with a standard interface, when used directly pluggable..
The motor is gear-reduced, the noise is extremely low, and it can be driven with 5V running smoothly..
Drive Module Board Size(in): 1.37*1.18*0.6.
Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board+Dupont Wire ..

♞【Product】3 Axis nema23 stepper motor driver usbcnc controller kit.
♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 425oz-in,280Ncm / Motor Size:57x57x112mm / Phase:2 / 4pcs lead wire / 1.8 Step.
♞【Stepper Motor Driver】FMD2740C Stepper Motor Driver / 4Amps / Support voltages:12 to 50V DC / 128microstep.
♞【4 Axis USBCNC breakout board】 Come with Hand Control with USB Cable / Only support USBCNC software / input voltage: 15-36V DC..
♞【DC Power Supply】400W 36V 11A DC Switching power supply.

5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
Motor diameter: 1.1 inches.Wire length：9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

【1】Package included: 1 x Stepper Motor Driver,1 x Stepper Motor, 1 x Wire..
【2】Suitable for a wide range of stepper motors from NEMA size 17,23 and 24 (42 * 42mm to 60 * 60mm). It can be used in various types of machines, such as XYZ tables, labellers, laser cutters, engraving machines, pick-place devices and so on..
【3】Motor driver: 9V-42V DC power supply, H-bridges bipolar constant phase current drive. The maximum 4.0A of the eight types of output current..
【4】The largest 32 divisions of the 6 models are optional.
Suitable for 4 wires, 6 wires and 8 wires stepper motor..
【5】Protect form: Overheated protection, overcurrent protection, undervoltage protection, prevention of inversion..

5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
Stepper motor with a standard interface could be connected with Driver Board easily.
A, B, C, D four-phase LED indicates the status of the stepper motor work..
5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.

Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..

Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32....
Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..

Mounts are thick 2mm metal bent into an L shape. spot-welded 2 little triangle-shaped wedges in the corners. Ideal for replacement applications..
Stepper motor bracket durable alloy steel provides strong bearing pressure when printing..
Nema17 brackets are 2 long slots so you could easily loosen screws, tighten the belt tension of the motor and belt, and tighten them back down easily..
Stepper motor alloy steel mounting bracket can match standard Nema 17 stepper motor, and also include the mounting holes for Nema 17 economy planetary geared stepper motor but not for high precision planetary geared stepper motor..
6 pcs of NEMA 7 stepper motor mounting brackets, 90 degrees L-shaped bracket there are 4 holes drilled to mount for 3D Printer Motors Nema 17 Stepper Motor 42-40 Motor..