Reviews Square Hollow Section Pipe

Rohn 25 Series 40' Basic Tower (25G)

  • INCLUDES: (1) ROHN 45AG2 STANDARD 9' 6" TOP SECTION, (5) 45G STANDARD 10' SECTION. 50' is a nominal description - actual assembled height will be less if the bottom section is partially embedded in concrete.
  • The ROHN 45G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 45G Guides for Specifications and Installation Requirements*.
  • 1-1/4" OD, 14 Gauge legs 7/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on a 16 3/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 45AG2 Features a tapered top and integrated mounting pipe. The mounting pipe is 2.38" OD / 2.07" Mounting PipeOverall length is 9'6" - see images for measurement breakdown. See description below for more information..
  • 45G Weight: 70 lbs. 45AG2 Weight: 66 lbs. *This kit is shipped via freight only, see below for more information*.
Check Stock

Weanas Aluminum Rod Tent Pole Replacement Tent Poles Accessories, Multifunction Lightweight Tent Pole Repair Kit, 7001 Series Aircraft-Grade Aluminum

  • ...ole, if your tent was Female End Pole, just need to pull out the male end, and holds it to the side. Then slide the male connector of the tent into the hollow tube. Pls follow the left picture guideline, any further issue, pls let us know. Total length of pole is 16'3"(496cm).
  • ASSEMBLED POLE SETDesigned for your easy usage to fit your tent, it's assembled, save your energy and time to install, open directly to replace whole fiberglass or aluminum tent pole. In the meanwhile, you can follow the left picture guideline to adapt to the female end connector.
  • BUILT TO LASTMade from the highest quality 7001 series aircraft-grade aluminum and high-quality bungee. This ensures the poles can take the bends well whereas many cheaper aluminum poles would have crumpled or snapped. Every Pole Sections are carefully handled for a smooth connection between pole sections for your really quick set-up/takedown.
  • VERSATILE AND DIY READYIf you only need to remove part of a section you can use a small pipe/tubing cutter to cut the aluminum section. Then just shorten the shock cord to match the new length. We've created these replacement aluminum tent poles so you can easily disassemble them to remove or a....
Check Stock

uxcell 5 Piece Square Round Pipe Plastic Chicken Drinker System S Hook Clamp

  • fit for : 20mm x 20mm square pipe, 24mm diamond pipe.
  • Package content : 5 x square pipe s hook clamp.
Check Stock

Rohn 25G Series 30' Basic Tower Kit

  • INCLUDES: (2) ROHN 25G STANDARD 10' SECTIONS, (1) ROHN 25AG2 STANDARD 9' 9" TOP SECTION *30' is a nominal description - actual assembled height will be less if the bottom section is partially embedded in concrete*.
  • The ROHN 25G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 25G Guides for Specifications and Installation Requirements. Professional Installation Required*.
  • 1-1/4" OD, 16 Gauge legs 5/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on an 11 1/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 25AG2 Features a tapered top and integrated mounting pipe. The mounting pipe, measured from the apex of the side rails, is 14 Gauge x 2.24" OD x 2.08" ID Overall length is 9'9" - see images for measurement breakdown. See description below for more information..
  • This tower kit ships via freight only. See below for more information. *Be sure your contact number is current on your order*.
Check Stock

Rohn 25G Series 20' Basic Tower Kit

  • INCLUDES: (1) ROHN 25G STANDARD 10' SECTIONS, (1) ROHN 25AG2 STANDARD 9' 9" TOP SECTION *20' is a nominal description - actual assembled height will be less if the bottom section is partially embedded in concrete*.
  • The ROHN 25G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 25G Guides for Specifications and Installation Requirements. Professional Installation Required*.
  • 1-1/4" OD, 16 Gauge legs 5/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on an 11 1/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 25AG2 Features a tapered top and integrated mounting pipe. The mounting pipe, measured from the apex of the side rails, is 14 Gauge x 2.24" OD x 2.08" ID Overall length is 9'9" - see images for measurement breakdown. See description below for more information..
  • This tower kit ships via freight only. See below for more information. *Be sure your contact number is current on your order*.
Check Stock

XIFOWE Copper Tube 1/4 OD x 3/16 ID 5 Ft Tube Wall 1/32 Refrigeration Seamless Round Pipe Tubing Soft Coil Copper Tubing Used In Refrigerators Freezers Air conditioners DIY projects Etc

  • 【Size】✔ 1/4" OD - 3/16" ID (6.35-4.75mm) | Tube Wall: 1/32" (0.8 mm) | Length: 5 Feet (1.524M). Note that the actual length of the copper tube is slightly longer than 5FT because it is measured manually. In addition, when we cut the copper pipe, we used a ring cutter, which will deform the section surface, resulting in a smaller inner diameter from the section surface. Please rest assured that this will only affect the size of the section surface, but not the actual size of the copper pipe..
  • 【Material】✔Soft copper pipe copper pipe is made of high quality copper material, the surface is smooth without seam. Note, because it is made of pure copper, so the surface is inevitably easy to oxidation and discoloration, can be polished with high mesh sandpaper, will become bright and clean!.
  • 【Good Thermal Conductivity】: Good heat dissipation and refrigeration capability, high strength at low temperature. This is a good choice for refrigerators, freezers, air conditioners and other refrigeration equipment.
  • 【Shape Changeable】Soft, Because copper pipe can bend and deform, they can often be made into elbows and joints. Smooth bending allows copper tubes to bend at any angle. Or used in manufacture of magnetism instruments or meters..
Check Stock

Portable, Progress Solar and Wind Powered Light Tower

  • Kit Includes (3) ROHN 25G STANDARD 10' SECTIONS, (1) ROHN 25AG2 STANDARD 9' 9" TOP SECTION *40' is a nominal description - actual assembled height will be less if the bottom section is partially embedded in concrete*.
  • The ROHN 25G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 25G Guides for Specifications and Installation Requirements. Professional Installation Required*.
  • Features 1-1/4" OD, 16 Gauge legs 5/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on an 11 1/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 25AG2 Features a tapered top and integrated mounting pipe. The mounting pipe, measured from the apex of the side rails, is 14 Gauge x 2.24" OD x 2.08" ID Overall length is 9'9" - see images for measurement breakdown. See description below for more information..
  • This tower kit ships via freight only. See below for more information. *Be sure your contact number is current on your order*.
Check Stock

Rohn 25G Series 50' Basic Tower Kit - Rohn 25G

  • INCLUDES: (4) ROHN 25G STANDARD 10' SECTIONS, (1) ROHN 25AG2 STANDARD 9' 9" TOP SECTION *50' is a nominal description - actual assembled height will be less if the bottom section is partially embedded in concrete*.
  • The ROHN 25G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 25G Guides for Specifications and Installation Requirements. Professional Installation Required*.
  • 1-1/4" OD, 16 Gauge legs 5/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on an 11 1/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 25AG2 Features a tapered top and integrated mounting pipe. The mounting pipe, measured from the apex of the side rails, is 14 Gauge x 2.24" OD x 2.08" ID Overall length is 9'9" - see images for measurement breakdown. See description below for more information..
  • This tower kit ships via freight only. See below for more information. *Be sure your contact number is current on your order*.
Check Stock

NDS 5

  • Protect your drainage system by using a grate on top of drain pipe to block debris from entering and potentially clogging the pipeline while letting excess surface water flow through. Ideal for draining light water flows from small lawns, landscaped areas, walkways, and patios.
  • Fits 4 in. Sewer and Drain Pipe & Fittings, 4 in. Single-Wall Corrugated Pipe, 4 in. Triple-Wall Pipe. 13 GPM flow rate. 4.3 sq. in. open surface area. Rated for NDS Class A loads (up to 60 psi) when properly installedrecommended for pedestrians, bicycles, and wheelchair traffic.
  • Place on top of drain pipe or drain fitting for a soil-tight fit. 5 in. Square Drain Grates are available in a variety of colors and materials.
  • Comes with one 5 in. Square Grate. Hassle-free limited lifetime warranty guarantees the NDS product is free from defectsor well replace it.
Check Stock

Single 12-48V DC LED FAA L-810 Obstruction Light, Red, Stead-Burning

  • INCLUDES: (1) ROHN 45AG2 STANDARD 9' 6" TOP SECTION, (1) ROHN SB45G 5' SHORT BASE FOR EMBEDMENT IN CONCRETE, (3) 45G STANDARD 10' SECTION, (1) ACWS ANTI-CLIMB WARNING SIGN KIT, AND ROHN 45G SELF-SUPPORTING TOWER SPECIFICATIONS. *This kit is shipped via freight only, see below for more information* *Be sure your contact number is current on your order*.
  • The ROHN 45G uses double bolted joints, proven to be the best method of joining tower sections for sturdiness and dependability. *See Rohn 45G Guides for Specifications and Installation Requirements*.
  • 1-1/4" OD, 14 Gauge legs 7/16" OD Solid Bracing Completely hot-dipped galvanized after fabrication. Built on a 16 3/4" equilateral triangle design.
  • Each section contains all required nuts and bolts shipped with each section. 45AG2 Features a tapered top and integrated mounting pipe. The mounting pipe is 2.38" OD / 2.07" Mounting PipeOverall length is 9'6" - see images for measurement breakdown. See description below for more information..
  • 45G Weight: 70 lbs. 45AG2 Weight: 66 lbs. SB45G Weight: 32 lbs.
Check Stock