Reviews Roofing Panel - BestBuyersPro.com

Metal Roofing Screws 250 12 x 2 ZINC/NO Paint Hex ReGrip Sheet Metal Roof Screw Sharp Point Metal to Wood siding Screws.

#12 Sheet Metal ROOFING SCREWS. Sharp Point ReGrip Screws. 5/16" Hex Head, ~9/16" Washer.
250 COUNT Metal-to-wood roofing screws are galvanized and zinc coated to prevent rusting.
Hex washer head, sharp point roof screw with EPDM washer seal, seals roofing panel to screws..
Corrugated roofing and corrugated siding screws for pole barns, storage shed, shops, etc..
Galvanized Screw is Non-Painted and gets it's Color from the Galvanizing Process and is natural gray.

Lightweight build simplifies installation.
Covered by a limited lifetime and 10-year hail damage warranty.
Roofing Product Type - Polycarbonate Panel.
Cover pergolas, patios, sheds and carports..
Polycarbonate construction is upto 20 times stronger than traditional fiberglass.

Easy to install adhered directly to metal roofing pans, no racking system is required, laminates and metal roofing can be installed in one step.
there are no penetrations to the roof deck It has flexible.
Powerbond, flexible solar panel. Peel & Stick..
Measures 216-inches in length by 15.5-inches width by 0.2-inches in height.

The Universal Ventilation System for all metal or polycarb panel roofs 2/12 to 20/12.
Tested Up to 110 MPH Wind Driven rain with NO measurable leakage. Apply to Ridge with Dual Strip 1/4" from edge of where Ridge Cap will be installed. Ridge cap is applied over top..
Pure Polyurethane Foam, Vinyl Coated, UV Stabalized/Fire Retardant.
2" Wide 1" Standard Thickness 20' Long with a double glue strip..
The Uni-Vent II Will conform to Virtually any metal or polycarb roofing panel. It compresses and fills every void between the ridge and roof panels. Factory applied glue strips allow the installer to roll out Uni-Vent II and apply it to the panel even in windy conditions. Any standard ridge cap will finish your installation..

Makes up to 1-1/2" (38.1 mm) deep bends along drip edge of roofing panel..
Durable lightweight steel and aluminum construction with weather-resistant finishes!.
For quick bends in standing seam panel edges.

Deformed ring shank for greater holding power electro galvanized to enhance corrosion resistance. Conforms to surfaces..
All hand driven caps are packaged as integral nail-cap units Cap nails round plastic burron cap ring shank lgth 1 inch count=250..
Flexible round head conforms to surface making it difficult for water to get under the cap. use to secure roofing felt, sheathing, building papers, etc..
Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe. Flexible plastic head..
Flexible round head conforms to surface making it difficult for water to get under the cap. Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe..

Ames Maximum-Stretch is a white, elastomeric, acrylic, rubberized roof coating & sealant with 650% elongation to resist cracking & peeling. With 88% light reflectivity, the bright white finish reduces surface temperatures resulting in lowered cooling costs..
Ames Maximum-Stretch adheres to metal roofing, tar, rolled roofs and more. Use as a RV roof sealant, waterproof sealant, rubber roofing material and more. Designed for low-slope roof maintenance..
650% elongation – does not flake, chip or peel – elastomeric and rubberized coating and sealant. Rubber roofing material is 88% light reflective resulting in lowered cooling costs. Brush, roll or spray on!.
Non-toxic, eco-friendly, low VOC & made in the USA.
1 Gallon – Our waterproof roof sealant is packaged in 1 gallon Pail. Designed for low-slope roof maintenance on metal roofing, built-up roofing, rolled roofing and more..

Dimensions: 5/16" Hex Head and ~9/16" EPDM washer - Shaft is .242" (#14) - Length under head 1".
#14 Sheet Metal roofing screws are galvanized for corrosion resistance.
Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
For installing roofing on a house, porch, airplane hangar, shed, pole barn, shop, barn or lean-to.
Rough Estimation - regular roofing project should require 80 screws per 10 x 10 section of roofing.

For clean, crisp bends in metal roofing materials!.
Quickly adjusts for making 5/8" to 4" (16 to 102 mm) bends in 29 to 22-gauge (0.36 to 0.76 mm) steel..
Exclusive 3-station roller design produces a uniform bend out to the very ends of a straight panel length..
Center roller station is also independently adjustable for making mild-angled bends on a curve..
Hardened rollers ensure long, service life..