Reviews Relay Connector - BestBuyersPro.com

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..

【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
【Wide Application】- These 5v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

Never go beyond its capabilities. Try to stay 10 to 15% below what the rate is for.
12-volt 5-prong relay. Excellent water-repellent and dustproof ability, but not using it in water.
Be careful when plugging the relay into the socket. If you push hard, you will bend the female connector.
Primary leads use 12 a.w.g tinned copper wire. Coil leads use 16 a.w.g.
SPDT relay: it has both normally open and normally closed terminals, terminal 87A is powered when the relay is inactive and switches the power to terminal 87 when the relay is activated.

36Vdc, 18Adc Output, 120 Vac 60 Hz Input.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
Output Connector Type: EZgo 2-Pin 'D' Shaped 36V Connector (Powerwise or TXT).

36Vdc, 18Adc Output, 120 Vac 60 Hz Input.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
Output Connector Type: SB50 (Grey) connector.

This product is designed for dual battery systems,suit for Most 12V Charging systems.surge protection,Automatically sensing voltage level of main battery.
Voltage Sensitive Relay:Voltage Sensitive Relay:Cut in volt 13VDC,Cut out volt 12.8VDC.Ensure main battery is always charged and ready to run the vehicle . the Dual Battery Isolator can charge 2 Battery systems.
Constructed with a weatherproof body IP65 and durable silver tipped contacts.
Package include：1X 24” length Red Cable (with single connector)丨1x12” length Red Cable (with two connector)丨1x12” length black Cable (with two connector)丨2x SC16-8 Lugs丨1x blue insulated ring terminal丨2x orange heat shrink cover丨3x nut,2x washer,4x screws.
2 Year Warranty:For any reason, if you are not satisfied with your purchase, contact us directly. We offer a 1-year warranty, 100% satisfaction guarantee..

36Vdc, 18Adc Output, 120 Vac 60 Hz Input.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
Output Connector Type: Star car Yellow 36 volt Three Pin Round Connector.

☞Fitment: For 4-Stroke GY6 Engine 50cc 70 cc 90cc 110 cc 150cc 200cc 250cc ATV Dirt Bikes Scooters Go Kart Dne Buggys Quad 4 Wheelers Pit Bike Moped Roketa SSR Taotao Sunl Coolster.
☞Material: Made of high quality copper and rubber material, efficient and durable.
☞Function: Solenoid starter relay is used for electronic applications to turn on / off most device, reduce startup switch electric current.
☞Great replacement: Reliable replacement electrical parts, direct plug-in, perfect replacement.
☞Package Included: 1pc solenoid relay (Have as a 2 wire 2 pin male connector end).

48Vdc, 17Adc Output, 120 Vac 60 Hz Input Golf Cart Charger.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
Output Connector Type: Yamaha G29 (Leaf) Style Connector.