Reviews Rear Axle Bushing Tool

lesolar Trailing Arm Bushing Tool Kit Suspension Control Arm Bushing Tool Kits Rear Bushing Removal Tool Kit with Storage Carrying Case Suitable for The Ford Focus Bushing Removal MK1 1998

  • 【Application】Control arm bushing tool kit has a wide range of application and strong practicality. It is suitable for Ford Focus MK1 & MKII 1998-2007, Ford Cuga 2008, Ford C-Max 2007, Mazda 3 sedan, hatchback 2003-2008, Mazda 5 CR, CW, MPV 2005, V50 2004-2012, S40 MK sedan 2003-2012..
  • 【Performance】Rear trailing arm bushing tool has excellent performance, which can protect your car from scratches, and it is used to silently press in and pull out the rear of the shaft to improve safety and reliability..
  • 【Easy to Use and Storage】Bushing removal tool kit is easy to use and install without the need to remove the rear axle, saving a lot of time. What's more, Heavy-duty plastic blow-molded carrying case is easy transportation, safe storage, and quick organization..
  • 【Material】Rear bushing tool kit is made of selected carbon steel. The greater the hardness, the higher the strength, and the lower the plasticity, the stronger the rust prevention, the longer the durability and the longer the service life..
  • 【After-sales Service】The trailing arm bushing kit has been strictly tested before leaving the factory.If you encounter any problems in the use process, please contact our customer service in time, and we will solve any difficulties for you ....
Check Stock

LEAPGOMAX EZGO Golf Cart Shocks Front or Rear Heavy Duty Coil Springs for EZGO TXT/Medalist 1994+ G&E Modified EZGO Golf Carts with Lift Kit OEM# 70928-G01 76418-G01

  • ...t of passengers, cargo or aftermarket accessories..
  • ⛳【Smoother Ride】These golf cart shocks will make a better and stable ride experience and would bump very smoothly. NOTE: EZGO shock is a standard length. Extenders will be needed for the rear if your cart with lift kit already..
  • ⛳【Easy to Install】All bushings are included with this EZGO golf cart shocks. Please  remove the front axle firstly. Then install the shock and install the front axle. Tighten the shocks until the bushing reaches the diameter of the bushing washer. Please compress the springs to get them fit..
  • ⛳【Notes】Please check the original ezgo shock size fits before you buy! (If your golf cart is equipped with a unsure size lifting device, please measure it before buying to see if it fits (16" original and 18" lifting equipment)..
Check Stock

OTC 4244 Freightliner Rear Suspension Bushing Tool

  • OTC's Freightliner Rear Suspension Tool features a robust 15-Ton capacity cylinder and installation/removal adapters.
  • Removes and installs single-wrapped FAS II Airliner Freightliner Rear Suspension Bushings 'on vehicle' - no need to remove the spring assemblies to use this tool.
  • Completes the job in a fraction of the time that traditional methods take.
  • Saves an average of 45 minutes per bushing (4 per vehicle) on flat rate of 1.5 hours per bushing - a huge time savings.
  • No more hammering prevents impact damage to suspension components while dramatically reducing the effort required by the technician performing the work.
Check Stock

ATPEAM 9-Way Slide Hammer Puller Set | Wrench Adapter Axle Bearing Hub Auto Set, Axle Front Rear Wheel Bearing Dent Hub Gear Puller Remover Set

  • ...g puller tool, locking plier adaptor, puller hook, and auto dent puller tool.
  • Wide Application: The 9-way slide hammer puller set with 4.8 lb slide hammer is ideal for a variety of pulling applications, including flange-type rear axles, most front-wheel-drive hubs, pulling dents, and other press-fit parts (bearings, bushings, gears, pulleys, etc.)..
  • Blow Mold Case: This bushing removal tool is packed in a heavy-duty, blow-molded case with precision-sized compartments for every piece - great for storage and transport while lengthening the life of the tool set..
Check Stock

8MILELAKE Rear Axle Bearing Puller Extractor Installer Set Axle Bearing Removal Remover Tool Kit

  • [APPLICATION]: This rear axle bearing puller can help to pull out semi-floating rear axle bearings quickly and effectively..
  • [EASY TO USE]: The washer of the axle bearing puller can captures the bearing firmly to distribute the force to the whole bearing, can avoid damage of the bearings and case..
  • [DURABLE MATERIAL]: The rear axle bearing removal tool is constructed from heavy duty cast steel, which has good strength and durability, can provide long service life..
  • [SIZE]: The bearing puller remover set includes fittings for main bearing tube: Small: 1" to 1-7/8.
Check Stock

OTC 4245 Freightliner Rear Suspension Bushing Master Tool Set with Air/Hydraulic Pump

  • OTC's Freightliner Rear Suspension Tool Master Set features a robust 15-Ton capacity cylinder, Air/Hydraulic pump, and installation/removal adapters.
  • Removes and installs single-wrapped FAS II Airliner Freightliner Rear Suspension Bushings 'on vehicle' - no need to remove the spring assemblies to use this tool.
  • Completes the job in a fraction of the time that traditional methods take.
  • Saves an average of 45 minutes per bushing (4 per vehicle) on flat rate of 1.5 hours per bushing - a huge time savings.
  • No more hammering prevents impact damage to suspension components while dramatically reducing the effort required by the technician performing the work.
Check Stock

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • ...ring and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
  • EASY STORAGE: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
  • PACKAGE CONTENTS: Package includes (3) rear axle bearing removers and (1) carrying c....
Check Stock

Orion Motor Tech 21PCS Master Ball Joint Press | Upper and Lower Ball Joint Removal Tool | Automotive Mechanic Tool Set

  • ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH 22PCS Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with multi-size adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle..
  • UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with all the receiver tubes and removing/installing adapters needed to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most GM, Chevy, Ford, and Dodge 2 and 4 wheel drive pickups, vans and sport utility vehicles, will service perfect for vehicles having the Dana 28, 30, 35, 44, 60 axle.
  • PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged solid carbon steel with anti-rust black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion..
  • CONVENIENTLY ORGANIZED IN CUSTOM MOLD....
Check Stock

E-cowlboy T-0220-39 Master Bushing Driver Set for Chrysler GM Ford Transmissions Bushing Bearing Seal Installer Remover Tool Kit (39 PCS)

  • 【Application】The custom bushing driver tool set is suitable for installing or removing wheel bearings, bushings, sealing rings and rubber. The tool is impact resistant and can be used with hydraulic presses and hammers..
  • 【Interchangeable】All 50 discs of the bush bearing and seal driver kit are interchangeable with each other and you can get 2,450 different size variations for quick work..
  • 【Quality Material】The bush removal puller bearing press tool is made of high-quality forged steel with a black anodized coating on the surface, effectively preventing rust and greatly extending the service life of the tool..
  • 【Custom Tool】8-65mm & 74mm metric discs. Each disc is marked with a scale for easy identification and reference. All metric discs, shafts, Allen keys, and screws remove or install bushings that are flush with the housing, allowing you to build your own custom bushing driver so that you always have the correct size for job..
  • 【Set Includes】The transmission wheel axle bearing seal installer kit includes: 48pcs*discs (18mm to 65mm with 1mm graduation) +1pc*disc (74mm) +1pc* handle/shaft +1pc*Allen wrench (3mm) +1pc*screw +1pc*storage box..
Check Stock

6602 Differential Bearing Preload Wrench Alternative to Miller C-4164 Suitable for Chrysler/Dodge Vehicles.

  • APPLICATION — vehicles equipped with 7-1/4, 8-1/4, 8-3/8, and 9-1/4″ rear axles such as Chrysler/Dodge vehicles..
  • FUNCTION — Similar to Miller C-4164. help remove the adjuster nuts when servicing the subject rear axles..
  • BENEFITS — Great tool make you able to loosen the bearing preloads within 3 mins! A simple but must have tool..
  • NICE DESIGN — Long enough to get to the adjusting nut from the axle tube. Red rubber sleeve for protecting the axle seal provides nice touch..
  • SATISFACTION GUARANTEE — If you are not satisfied with Camoo products, simply asked money back guarantee with 12 months warranty. No worry about buying!.
Check Stock