Reviews Plumbing Code Illustrated

RENO 316 Marine Grade Brushed Stainless Steel Massage Outdoor Shower Panel Swimming Pool Backyard Bathroom Hot & Cold Rainfall Hand Held Wall Mounted or Free Standing Outside Shower

  • ... Quality Stainless Steel, which means this Shower WILL NOT RUST! So you can easily enjoy it either Outside or Inside your home..
  • cUPC REGISTERED- Purchase with Confidence as this product has been Tested & Registered with the UPC Code of compliance, which is the Uniform Plumbing Code (UPC) and Canadian Uniform Plumbing Code (cUPC) which are designated as the American and Canadian national standards, respectively. These codes are designed to provide consumers with safe and sanitary plumbing systems and a piece of mind..
  • COMPLETE SHOWER SYSTEM WITH INTERNAL HOT & COLD PLUMBING! -This shower comes with Full Internal Pre-Installed Plumbing , no need for extra parts! All that needs to be done is to connect this unit to Hot & Cold water supply..
  • CAN BE INSTALLED FREE STANDING OR WALL MOUNTED-Enjoy this shower anywhere you like as it can be installed Free Standing, which means you can install it next to the swimming pool or anywhere in your backyard. And since it can be Wall Mounted as well, you can easily install it on your fence, on the wall or inside the bathroom..
Check Stock

Holdrite QS-U Expansion Bracket Stainless Steel

  • SAFE: Straps secure water tank to wall and takes weight load off thermal pipes.
  • MATERIAL: Galvanized and Stainless Steel construction support heated water tanks.
  • SIZE: Supports 5-gallon hot water tanks up to 13 inches in diameter.
  • RATED: Heater is compliant with Uniform Plumbing Code and International Plumbing Code requirements.
Check Stock

Watts Premier WP116187 Top Mount Twist Air-Gap Monitored Faucet, Brushed Nickel

  • TUBING SPECIFICATIONS: 1/4 inch Blue tube approximately 4 feet in length for connecting drinking water, 1/4 inch Red tube approximately 4 feet in length for connecting to the air gap of the faucet, and 3/8 inch Black tube approximately 3 feet in length for the connection to the drain.
  • PLUMBING CODE: This Faucet requires access to a drain connection. The Faucet conforms to all US Plumbing Codes. US Plumbing Code (5-202.13 Backflow Prevention, Air-Gap. An air gap between the water supply inlet and the flood level rim of the plumbing fixture, equipment, or nonfood equipment shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch)..
  • See attached installation manual in the Technical Details section.
Check Stock

Drain Line Adapter (DLA) With 1/2-inch Barb Fitting for a Water Filter and 7/8-inch Fitting for a Dishwasher (ET116-004, D-50B, DLA-D)

  • ...nector accommodates various inside diameter (ID) dishwasher hoses (1/2-, 5/8-, 3/4-, or 7/8-inch). Its reverse osmosis 1/2-inch barb insert fits 1/2-inch ID RO drain tube. A hose coupler and stainless steel clamps are provided for a secure connection to the garbage disposal inlet. The ET116-004 installation enables plumbing pipes to stay intact..
  • ❤ DRAIN LINE CONNECTION: The ET116-004 enables the connection of the RO water filter to a garbage disposal with a dishwasher. Installing the ET116-004 is simple and allows bypassing the existing plumbing but with no pipes to undo..
  • ❤ QUIET OPERATION: The ET116-004 is designed to eliminate most reject water noise. It is also equipped with a self-cleaning port..
  • ❤ CERTIFICATION: The ET116-004 is legal to install in any state. It is UPC (Uniform Plumbing Code) Listed, IPC (International Plumbing Code), and NSF (National Sanitation Foundation) tested. These certifications assure that ET116-004 is safe to use. The testing is conducted for every manufactured lot to ensure consistent performance..
Check Stock

Drain Line Adapter (DLA) With 1/4-inch Quick Connect Fitting for a Water Filter and 7/8-inch Fitting for a Dishwasher (ET116-001, D-25QC, DLA-D)

  • ... dishwasher connector accommodates various inside diameter (ID) dishwasher hoses (1/2, 5/8, 3/4, or 7/8-inch). Its reverse osmosis 1/4-inch push-in connector fits 1/4-inch RO poly tubing. A hose coupler and clamps are provided for a secure connection to the garbage disposal inlet. The ET116-001 installation enables plumbing pipes to stay intact..
  • ❤ DRAIN LINE CONNECTION: The ET116-001 enables the connection of the RO water filter to a garbage disposal with a dishwasher. Installing the ET116-001 is simple and allows bypassing the existing plumbing but with no pipes to undo..
  • ❤ QUIET OPERATION: The ET116-001 is designed to eliminate most reject water noise. It is also equipped with a self-cleaning port..
  • ❤ CERTIFICATION: The ET116-001 is legal to install in any state. It is UPC (Uniform Plumbing Code) Listed, IPC (International Plumbing Code), and NSF (National Sanitation Foundation) tested. These certifications assure that ET116-001 is safe to use. The testing is conducted for every manufactured lot to ensure consistent performance..
Check Stock

HoldRite QuickStand 22 Inch Water Heater Stand, Up to 52 Gallons, Unassembled, 40-S-22-U

  • WATER HEATER STAND: The Holdrite QuickStand Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
  • WHAT IS INCLUDED: The QuickStand is easy to assemble and includes (2) safety clips and (2) lag bolts.
  • assembled QuickStand measures 22 inches in diameter by 16 inches in height.
  • CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 52 gallons.
  • VERSATILE: This water stand can be installed on concrete or framed walls.
  • can also support other equipment such as tanks, washers, and boilers.
  • CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.
Check Stock

HoldRite QuickStand 30 Inch Water Heater Stand, Up to 100 Gallons, Unassembled, 40-S-30-U

  • WATER HEATER STAND: The Holdrite QuickStand Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
  • WHAT IS INCLUDED: The QuickStand is easy to assemble and includes (2) safety clips and (2) lag bolts.
  • assembled QuickStand measures 30 inches in diameter by 16 inches in height.
  • CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 100 gallons.
  • VERSATILE: This water stand can be installed on concrete or framed walls.
  • can also support other equipment such as tanks, washers, and boilers.
  • CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.
Check Stock

Eastman 24 Inch Water Heater Stand with Screws, 75 to 100 Gallons Load Rate, 86279

  • WATER HEATER STAND: The Eastman Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
  • WHAT IS INCLUDED: This water stand is easy to assemble and includes safety clips to fasten the stand to the wall or floor so that nothing can shake your water heater off its place.
  • CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 100 gallons.
  • VERSATILE: This water stand can be installed on concrete or framed walls.
  • can also support other equipment such as tanks, washers, and boilers.
  • CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.
Check Stock

Practicon 7078713 Gleco Trap System 64 oz.

  • Side drain siphons out all water prior to removal, eliminating spillage.
  • Adapts easily to existing plumbing - the Gleco Trap is the only plaster trap to meet US Uniform Plumbing Code.
Check Stock

Flashers #7 Black EPDM Flexible Roof Jack Pipe Boot Metal Roofing Pipe Flashing (Pipe OD 6\ to 11\) - 100% Made In The USA

  • MANUFACTURER DIRECT: 100% Made in the USA by an American Workforce.
  • EPDM Flashers are rated to service a continuous temperature range of -65 to +250 degrees Fahrenheit..
  • Flashers’ flexible rubber won’t crack and allows for expansion, contraction, and pipe vibration. The heavy rubber fold and aluminum ring at the base allows them to fit any roof pitch or metal profile..
  • Flashers require no special tools or complicated installation methods. The rubber cone is clearly marked with pipe dimensions, in both inches and millimeters, so it can be easily customized with tin snips or scissors..
  • Our Flashers product line holds a Certificate of Listing with IAPMO R&T. This shows our products are in compliance with the Uniform Plumbing Code (UPC) and International Plumbing Code (IPC)..
Check Stock