Reviews Pipe Thread Fittings

Anderson Metals 56120-0806 Brass Pipe Fitting, Adapter, 3/8' Male Pipe x 1/2' Female Pipe

  • Adapter for connecting pipes or fittings of different types.
  • Male National Pipe Taper (NPT) threads on one end and female NPT threads on the other for connecting pipes with different ends. Please see NPT Thread - chart to determine the correct size required. Pipe Size and actual Thread OD are different. The Thread OD is larger than the Pipe Size..
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Operating temperatures range from -53 to 121 degrees C (-65 to 250 degrees F).
  • Meets specifications ASTM B584 and ASME/ANSI B16 for quality assurance.
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
Check Stock

Drainzit STAN1438 Oil Change Aid for Briggs & Stratton Tecumseh 3/8' Oil Port

  • Drainzit oil hoses make changing oil easier and cleaner. Drainzit is easy to install, simple to use and requires no engine modification. For use on nearly all equipment powered by small engines: pressure washers, generators, pumps/sprayers, compressors, lawn mowers and more. Fits most briggs and stratton, tecumseh engines with 3/8 in. pipe thread oil drain port, Kohler command and OHC 16 and 18 HP Fittings convert to SAE wrench sizes Efficient - custom made metric fittings seal kit to.
  • Fits most briggs and stratton, tecumseh engines with 3/8 in. pipe thread oil drain port, Kohler command and OHC 16 and 18 HP.
  • Efficient - custom made metric fittings seal kit to engine with O-ring.
  • Rubber retainer loop holds kit in place when not in use.
Check Stock

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 20.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5”....
Check Stock

Hooshing Brass Pipe Fitting, 1/2' Female to 1/2' Male Pipe Nipple Extension Connector Fitting, Hex Bushing Adapter, Reducer Adapter, Solid Brass Length 1.97 Inch/50mm

  • 【Material】High quality soild brass for corrosion resistance, high temperature ductility and low magnetic permeability. Strong and durable..
  • 【Size】1/2 Inch Female x 1/2 Inch Male Thread, the thread is NPS, have no tapered. It's straight thread..
  • 【Extension Design】Length: 1.97 Inch/50 mm, can be used to extend the length of the pipe or fitting.Deeper and smoother threads makes work easier and more efficient..
  • 【Widely Applications】Use to extend shower fixtures/arms through walls, extend tub spouts.Also be used with grease, fuels and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
  • 【Note】Brass pipe fittings for connecting pipes or fittings of different thread types, can be used in wet environments.Not recommended for potable water..
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 21 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34” Longest Length (not including fittings) x 9” x 16” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe....
Check Stock

Gsinodrs 3PCS Brass Pipe Fitting 1/2 Female NPT Thread x 1/2 Male NPT Thread Brass Hex Pipe Fittings Adaptor 1200psi High Pressure

  • 【Metal Adapter】Our pipe fitting solid brass constructed, strong and wear resistant more durable than iron and iron galvanized pipe fittings. 3PCS-....
  • 【Durable and Steady】Heavy duty brass pipe fitting construction has excellent performance in terms of corrosion resistance, high temperature....
  • 【Widely Application】Adapter for connecting pipes or fittings of different thread types, brass is corrosion resistant and can be used in wet....
  • 【Temperature Rating】Operating pressure of our fittings is up to 1200psi, more higher than other general fittings. Temperatures range from -53 to....
  • 【Reliable Quality】The pipe fittingadapter can widely used in your life. 24 months warranty for the adapter, any issue, please contact us..
Check Stock

Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male ....
Check Stock

Joywayus Hex Nipple 1/2' Male x 1/2' Male Threaded Stainless Steel 304 Threaded Nipple Pipe Fittings for Brew Kit Home Piping (Pack of 5)

  • 【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
  • 【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
  • 【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
  • 【Operating temperature range】Temperature rating: -65 to 250 degrees F.
  • 【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
  • it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
Check Stock