Reviews Motor Driver Boards

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

  • 【Brussless Spindle Motor】Power: 400W.
  • Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
  • 【Brussless Spindle Motor Driver】Maximum driver power: 600W.
  • Maximum driver motor running speed: 12000R/Min.
  • Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
  • The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....
Check Stock

Saiper Flexible Couplings 5mm to 8mm (5pcs) Aluminum Alloy Joint Connector Compatible with NEMA 17 Stepper Motors, RepRap 3D Printer or CNC Machine, 3D Printer Accessories

  • Fully assembled & tested, no soldering required, Can be extended to control other accessories..
  • It has Cartesian robots and requirements of the extruder, Heated bed control with additional 11A fuse. Fits up to 5 stepper driver board..
  • Three field effect transistors, three heater / fan output ports, three thermistor circuits.A number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack..
  • The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Pololu board foot socket, can be easily replaced or removed..
  • The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion..
Check Stock

KEYESTUDIO L298P Motor Driver HAT Shield GPIO for Raspberry Pi Model B/B+/A+/2/3/4 Zero and Zero W, High-Power Motor Speed Control Board Dual H Bridge with IR Receiver

  • This Motor Driver HAT gives your Raspberry Pi the ability to drive two DC motors, with drive current up to 2A..
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards like Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions.
  • Reserved I2C SPI control pins, allows to work with other control boards and sensors. Comes with an IR receiver for communication with an infrared remote controller..
  • Included 4x M2.5*20MM screws, 4 xM2.5*10MM copper pillars, 4x M2.5 Nuts. Easy to install on your RPi board. Please note Raspberry Pi board, remote control and motors in the photos are Not Included!.
Check Stock

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

  • 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface could be connected with Driver Board easily.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
  • Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.
Check Stock

Myard Universal Hidden Deck Fastener Clips for Grooved Edges of Composite Decking Boards to Joists, 1/4' Gap Spacing, with Square Driver Bit (50-Pack)

  • ▼ 50-Pack. ▼ Black stainless steel screws (Hardness class #12.9 + Dacromet black coating) are included. Saving time and money. ▼ Made of anti-UV engineering Nylon plastic. No corrosion. ▼ Includes 1 Square Driver Bit: Size 0.09″ x 0.09″ (2.3mm x 2.3mm).
  • ▼ Clean-look and consistent 1/4″ deck board spacing. No more predrilling and countersinking. ▼ Decking grooved edges “C” opening must be 0.15″ or bigger..
  • ▼ Compatible with AZEK, Cali-Bamboo, Deckorators, DuraLife, Envision, EverNew, Fiberon, MoistureShield, Lumberock, TimberTech, Trex, WearDeck, Zuri branded edge-grooved composite, hardwoods, treated lumber, cedar, & vinyl deck boards..
  • ▼ INSTALLATION: (1) Insert a Myard hidden fastener clip into the grooved edges of decking over a joist. (2) Drive the screw ONLY halfway (Fully tighten later once all boards are in place). The wings must remain level with the joist for the next board to fit correctly. (3) Continue to add clips on each joist against deck boards..
  • ▼ INSTALLATION: (4) Install “next” boards, make sure boards are pressed firmly against the clips and secured under the wings. (5) Do NOT over-tighten the screws. Please set proper driver torquing (2 to 6 drill power). The screw head will be resti....
Check Stock

Myard Universal Hidden Deck Fastener Clips for Grooved Edges of Composite Decking Boards to Joists, 1/4' Gap Spacing, with Square Driver Bit (100-Pack)

  • ▼ 100-Pack. ▼ Black stainless steel screws (Hardness class #12.9 + Dacromet black coating) are included. Saving time and money. ▼ Made of anti-UV engineering Nylon plastic. No corrosion. ▼ Includes 1 Square Driver Bit: Size 0.09″ x 0.09″ (2.3mm x 2.3mm).
  • ▼ Clean-look and consistent 1/4″ deck board spacing. No more predrilling and countersinking. ▼ Decking grooved edges “C” opening must be 0.15″ or bigger..
  • ▼ Compatible with AZEK, Cali-Bamboo, Deckorators, DuraLife, Envision, EverNew, Fiberon, MoistureShield, Lumberock, TimberTech, Trex, WearDeck, Zuri branded edge-grooved composite, hardwoods, treated lumber, cedar, & vinyl deck boards..
  • ▼ INSTALLATION: (1) Insert a Myard hidden fastener clip into the grooved edges of decking over a joist. (2) Drive the screw ONLY halfway (Fully tighten later once all boards are in place). The wings must remain level with the joist for the next board to fit correctly. (3) Continue to add clips on each joist against deck boards..
  • ▼ INSTALLATION: (4) Install “next” boards, make sure boards are pressed firmly against the clips and secured under the wings. (5) Do NOT over-tighten the screws. Please set proper driver torquing (2 to 6 drill power). The screw head will be rest....
Check Stock

3 Axis CNC Kit Nema23 Stepper Motor Dual Shaft 425oz-in 112mm 3A & Driver 40VDC 4A 128 microstep for CNC Router Milling Engraving Machine

  • ♞【Product】3 Axis nema23 stepper motor driver usbcnc controller kit.
  • ♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 425oz-in,280Ncm / Motor Size:57x57x112mm / Phase:2 / 4pcs lead wire / 1.8 Step.
  • ♞【Stepper Motor Driver】FMD2740C Stepper Motor Driver / 4Amps / Support voltages:12 to 50V DC / 128microstep.
  • ♞【4 Axis USBCNC breakout board】 Come with Hand Control with USB Cable / Only support USBCNC software / input voltage: 15-36V DC..
  • ♞【DC Power Supply】400W 36V 11A DC Switching power supply.
Check Stock

MINARIK MM23001C 0-90/0-180V-DC 1/4-2HP 5A AMP DC MOTOR DRIVE D506404

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

RIDGID 18V Brushless 1/2" High Torque Hammer Drill/Driver

  • Drill/Driver: All Metal Gears For extended durability.
  • Drill/Driver: 24 Position Clutch Ring For ultimate precision when driving.
  • Impact Driver: Quick-Release Hex Collet Spring ejection for easy loading and removal.
  • Impact Driver: High Torque Output 0 - 1,800 in-lbs. of Torque.
  • Brushless Motor Technology Delivers more runtime, more power, and longer motor life.
Check Stock

18V SubCompact Brushless 1/2 in. Drill/Driver and Impact Driver Combo Kit

  • Drill/Driver: All Metal Gears For extended durability.
  • Drill/Driver: 24 Position Clutch Ring For ultimate precision when driving.
  • Impact Driver: Quick-Release Hex Collet Spring ejection for easy loading and removal.
  • Impact Driver: High Torque Output 0 - 1,800 in-lbs. of Torque.
  • Brushless Motor Technology Delivers more runtime, more power, and longer motor life.
Check Stock