Reviews Mmdvm Hotspot

MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Supports Digital Radio Only NXDN POCSAG P25 YSF DSTAR C4FM DMR

  • ✔➸ Added external inductor. Support VHF communication, the effect cannot reach the perfect effect of UHF.
  • ✔➸ MMDVM hotspot is a fully-assembled device..
  • ✔➸ HOTSPOT comes pre-configured for a Wi-Fi network. SSID: Pi-Star (or Pi-Star-Setup) Password: raspberry, Just connect to temporarily WIFI: pi-star then you can access the device through your web browser using Pi-Star. And then save your own house WIFI details to HOTSPOT according to the step 2 of the instruction manual..
  • ✔➸ HOTSPOT size: 2.8 x 1.3 x 0.9” inch.
Check Stock

Yunseity Duplex Hotspot Board, 3.5Inch Screen MMDVM Duplex Hotspot Board with Cooling Fan, DMR Standard, Digital Display Hotspot Repeater with Antennas

  • APPLICABLE MODEL: MMDVM mini hotspot repeater board, duplex dual time slot design, mainly used for the built in extension board for Raspberry Pi 3B..
  • WITH COOLING FAN: The hotspot board has mini cooling fan for easy operation for long periods of time, and the acrylic case adds elegance to the product..
  • MEMORY CARD: Including 16G or 8G small memory card, the writing speed is not less than 10M, which has high efficiency and good durability..
  • GOOD PERFORMANCE: The digital hotspot board has the advantages of optimized wiring, perfect component layout, low heat generation, fast heat dissipation..
  • DMR STANDARD: All debugging parameters are carefully debugged according to the DMR standard, more stable in use and greatly improve the sound restoration..
Check Stock

MMDVM Hotspot Board + Aluminium Case Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, Pi 3 (Raspberry Pi NOT Included)

  • Save electricity, High quality TCXO, stable, low BER. Note: This is NOT a completed or assembled Hotspot, it is just MMDVM Board with Aluminum case..
  • Support Raspberry Pi 3B, Pi ZERO, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model).
  • Support VHF/UHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions).
  • Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG.
  • Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules.
Check Stock

MMDVM Hotspot Spot Assembled Radio Station OLED Antenna WiFi Digital Voice Modem P25 DMR YSF C4FM Raspberry Pie Pi

  • MMDVM hotspot supports D-STAR DMR YSF P25 NXDN POCSAG, enables the different mode of digital two way radio to communicate with each other (YSF2DMR / YSF2NXDN / YSF2P25 / DMR2YSF / DMR2NXDN) and works great with UHF..
  • Setup: Set the same freq as Radio Mobile, for example: 433.550000MHZ. DMR WIFI SSID:pi-star,PASSWORD:raspberry. Need the 2.4GHz SSID as the Pi Zero W. doesn't support 5.8GHz.
  • Power Supply: Mobile charger or a USB cable connected to your computer or laptop..
  • Best customer services: fully-assembled. The firmware is pre-loaded. Contact us if any question, we will reply within 6 hours. 73.
Check Stock

All-New Duplex DMR Hotspot Ehternet Port Assembled Radio Station WiFi Voice Modem Support DMR Dstar YSF P25 Fusion Antenna Raspberry Pi Model 2B Two Colors OLED 2 TimeSlots

  • MMDVM hotspot supports D-STAR DMR YSF P25 NXDN POCSAG, enables the different mode of digital two way radio to communicate with each other (YSF2DMR / YSF2NXDN / YSF2P25 / DMR2YSF / DMR2NXDN) and works great with UHF..
  • Two Time Slots: Support receive in one Frequency and transfer in another frequency using Duplex mode.
  • Upgraded Network: support wifi wireless connection and wired connection to the router directly..
  • Power Supply: 5V, Mobile charger or a USB cable connected to your computer or laptop..
  • Best customer services: fully-assembled. The firmware is pre-loaded. Contact us if any question, we will reply within 6 hours. 73.
Check Stock

Hima MMDVM Hotspot Spot Radio Station+ Antenna + OLED with Screen Support P25 DMR YSF D-Star UHF Expansion Board WiFi Digital Voice Modem Suitable for Raspberry Pi-Zero W, Pi 3, Pi 3B+

  • The kit includes: high performance with screen ARM processor, SMA antenna connector, including antenna, 2 pins, 4 screws..
  • Support:D-STAR, P25, DMR and work with UHF.Software:Pi-Star,Suit for Raspberry Pi 3,Raspberry PI-Zero w, Raspberry Pi 3b+.The 40pin raspberry pie needs to insulate the middle 20pin pin headers for normal use..
  • Power supply: USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network..
  • Basic Setup: 433.550000MHZ DMR (Need the 2.4GHz SSID as the Pi W doesn't support 5.8GHz)..
  • Note: All designs will be contributed on MMDVM open source project.If you encounter a different version of pi zero not work, please see the picture instructions. If you have any difficult， please contact us to help you solve the problem..
Check Stock

Zebra DRPi-1S .096 Screen Case – Raspberry Pi 3 B+ and Duplex MMDVM Black Ice

  • For Raspberry Pi 3B+, 3B, 2B, and B+ (not included), Duplex MMDVM (not included), and an OLED screen (not included)..
  • Full body coverage for Raspberry Pi, MMDVM DUPLEX v1.3 & v1.0, and OLED screen (not waterproof).
  • Enough room for .96 128x64 OLED screen (smaller style antenna recommended when using a screen).
  • Cut outs for easy access to SD card and ports.
Check Stock

C4Labs DRPi-1NSX case for Raspberry Pi 3 B+, Duplex MMDVM v1.0, 2.4″ Enhanced Nextion Screen (Included) ~ (Black Ice)

  • Full body coverage for Raspberry Pi 3B (not included), Duplex MMDVM v1.0 dual antenna (not included), and 2.4" Nextion Touchscreen(included). Case kit requires assembly. Case is not waterproof..
  • Includes a 2.4″ Enhanced Nextion Touchscreen**Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • For Raspberry Pi 3B+, 3B, 2B, and B+ (not included), Duplex MMDVM v1.0 (not included), and a 2.4″ Enhanced Nextion Touchscreen (included).
  • Designed and Crafted by Local Artists at our workshop in Tacoma, WA USA.
Check Stock

C4Labs JRZ-1SB case Compatible with Raspberry Pi Zero/Zero W & JumboSPOT MMDVM & Waveshare UPS Hat (Black Ice)

  • Full body coverage for Raspberry Pi, Battery Hat, JumboSPOT or LoneStar N5BOC MMDVM Simplex and OLED screen (not waterproof) Note: Raspberry Pi Zero 2 has not been tested for heat issues..
  • Enough room for .96″ OLED screen to be mounted directly to JumboSPOT or LoneStar N5BOC MMDVM Simplex by customer.
  • Cut outs for easy access to SD card and camera ports.
  • Pin-hole access to boot and reset buttons on top of case.
  • No components are included. This is a Case Kit and assembly is required..
  • Designed and Crafted by local artists in Tacoma, WA USA.
  • Comes with 2 tops: one with antenna hole and one without.
  • Compatible with Lonestar N5BOC Board version 03/23/2019 1V8-1.
Check Stock

C4Labs JRPi-3.5NSX Nextion Screen Case for Raspberry Pi 4B & 3B+, Jumbospot MMDVM, and 3.5\ Nextion Screen (Included)

  • If you have a Zumspot Brand MMDVM Board there is a new case model: ZRPI-3.5NSX.
  • For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), JUMBOspot (a generic Chinese MMDVM board - Not included), and a 3.5″ Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included..
  • *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • Engineered and manufactured with Pride in Tacoma, WA USA.
Check Stock