Reviews Metal Lath - BestBuyersPro.com

10000 #8 X 3/4 Phillips Modified Truss Head K-Lath Sharp Point Screw Zinc Plated Bulk Box 50 Lbs.

Widely used for wood-to-metal applications such as metal lath in stucco/other to 22-18 steel studs..

Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Used for the Attachment of Metal and Plastic Lath, Plaster Repair, Insulation Board, and Gypsum Sheathings.
4 Keyholes for Bonding of Plaster and Basecoats.
4 Tabs for Pre-Spotting Washer into Soft Material Such as Insulation Board.
Center Hole will Accommodate Screws to #12.

Zircon’s MS 740 is a multi-surface scanner with 4 modes that allow you to detect and mark the location of studs, metal and live AC wiring.
ACT (Auto Correcting Technology) that automatically corrects common user errors, such as when scanning begins over a stud, in addition to the unique floating head design that keeps the sensor flat on rough and textured surfaces to increase the accuracy of results.
Both StudScan and DeepScan modes locate the edges, center and direction of wood or metal studs and joists.
Metal Scan mode finds both non-ferrous metal (such as copper pipe) and ferrous metal (such as rebar) even through lath and plaster.
AC Scan finds and traces live, unshielded electrical AC wires.
WireWarning Detection indicates the presence of live, unshielded electrical AC wiring while scanning in StudScan, DeepScan, and Metal Scan modes.
Integrated erasable wall marker enables users to mark targets with the simple push of a button.

Find ferrous and non-ferrous metal up to 6 in. (152 mm) deep in concrete and other non-metallic surfaces.
Automatically differentiates between magnetic metal (such as rebar) and non-magnetic metal (such as copper pipe).
Shows the depth of metal from the surface in both inches and centimeters.
Helps map out the grid of metal through any nonmetallic construction material, including concrete, tile, and marble.
Ideal for finding and/or avoiding rebar, cables, pipe, nails in reclaimed wood, nails/tacks in studs behind lath & plaster walls, electrical boxes and....