Reviews Mattress For Ls1

NEW GM T-56 HYDRAULIC THROWOUT BEARING,97-04 CORVETTE,98-02 CAMARO,LS1,LS6,LS7

  • Brand New Ram Hydraulic Throwout Bearing Kit for Stock Style Clutches with GM Tremec T-56 Transmissions (Ram Part #78165)..
  • Fits GM Tremec T-56 transmissions in: * 1997-2004 Chevy Corvette with LS1, LS6, and LS7 engines. * 1998-2002 Chevy Camaro with LS1 engines. * 1998-2002 Pontiac Firebird with LS1 engines..
  • Fits stock style clutches. * Includes a replacement transmission collar to install on your T-56..
  • Includes a remote bleeder line, as well as a supply line. The factory supply line is cut and the adapter fitting (included) is installed with the new supply line..
  • Also, includes a set of conical shims to properly fit the bearing, installation stud, inlet, outlet, and conversion fittings, as well as installation instructions..
Check Stock

HOLLEY MODULAR LO-RAM EFI MANIFOLD KIT,TOP-FEED PLENUM,BLACK FINISH,COMPATIBLE WITH GM LS1,LS2 & LS6 GEN III & IV ENGINES

  • ...-Feed Plenum, Black Finish, Compatible with LS1, LS2 & LS 6 Gen III & IV Engines (Part #300-620BK).
  • The 300-620 top-feed plenum entry configuration is designed to allow the included Hi-Ram 105mm plenum top to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications was conceived to package with an air to water plenum mounted intercooler with a shorter overall height than possible with other existing intake manifolds..
  • The Holley LS1/2/6 Lo-Ram intake manifold kits are designed for GM LS Gen III & IV engines equipped with GM LS1/2/6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The fuel rail kits come with 2 sets of brackets: A set for long (usually standard length) fuel injectors & set for short (such as Pico, or LS7) fuel injectors..
  • NOTE: Total Height: Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top - 9.07" (without intercooler installed) | Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top, w/ intercooler installed - 9.07" + intercooler thickness.
  • Specs: Brand: Holley EFI | Color: Black | Construction: Cast | Emission Code: 3 | Engine: GM LS1/LS2/LS6 | Finish: Black | Flange Sty....
Check Stock

Michigan Motorsports LS1 Rocker Arms and Bolts with Trunion Kit Installed FITS LS2 LS6 LQ4 LQ9 LM7 4.8 5.3 5.7 6.0

  • Whether you have a stock LS motor or a highly modified LS motor, replacing your rockers with a true roller bearing setup is highly recommended. The stock bearings have a tenancy to fail. These rocker arms are a must have for any aggressive heads and cam combo and are the same rockers we utilize on our 1,000 hp Turbo Motor..
  • We utilize LS rocker arms and install new LS1 rocker arm retro-fit trunion kit that replaces the cageless, loose OEM needle bearings and powdered metal trunion with a premium 8620 steel alloy trunion and caged roller bearings for added durability. The caged roller bearings that greatly reduce the possibility of the bearing failure experienced with stock LS1 needle bearings, which can send loose needles throughout the engine upon failure..
  • LS1 style allen head bolts are included for installation. Whether you have a stock LS motor or a highly modified LS motor, replacing your rockers with a true roller bearing setup is highly recommended. The stock bearings have a tenancy to fail. These rocker arms are a must have for any aggressive heads and cam combo and are the same rockers we utilize on our 1,000 hp Turbo Motor.
  • This kit includes: 16 LS Series Rocker Arms 16 rocker arm trunnions- LS-type retrofit 32 rocker arm bearin....
Check Stock

Remflex 2048 Exhaust Gasket for Chevy V8 Engine, (Set of 2)

  • Chevy V8 - 4.8L, 5.3L, 5.7L- LS1, LS6/6.0L- LS1, LS2 Vortec, 1-1/2" RP, For Weld Bead Headers, 2/Set.
  • additional sealing material is provided around the weld bead to provide a better seal.
  • There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.
Check Stock

NEW 3 BAR MAP SENSOR LS1 LS2 LS3 LS7

  • Plug and play adapter that will allow the installation of an LS3 MAP sensor in an LS2 or LS1 equipped vehicle..
  • Delphi Style MAP Sensor to a Bosch Style LS MAP Sensor.
  • Included components: MAP Sensor Adapters Harness (6 inch).
Check Stock

Remflex 2049 Exhaust Gasket for Chevy V8 Engine, (Set of 2)

  • Reflex's unique flexible graphite material has been proven for more than 30 years.
  • Chevy V8 - 4.8L, 5.3L, 5.7L- LS1, LS6 /6.0L- LS1, LS2 Vortec, 1-3/4" Round Port, For Headers, 2/Set.
  • Remflex exhaust gaskets come in a standard 1/8 inch thickness and are designed to crush 50 percent allowing them to fill any pits or gaps in the flange surface up to 1/16 inch.
  • There are no rubber binders or composite materials in Remflex Exhaust Gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.
Check Stock

Michigan Motorsports Front Crankshaft Damper Seal Gen 3 Gen 4 LS LS1 4.8 5.3 5.7 6.0 6.2 7.0

  • Michigan Motorsports LS1 Front Crankshaft Damper Seal.
  • Fits all 1997-2013 Gen 3&4 LS Based V8 Engines.
  • LS1 LS2 LS3 LS6 LS7 LS9 L99 LSA LS9 L92 L9H L94 LS2 L76 L77 LY6 L96 LFA LZ1 LY5 LMG LMF LH6 LC9 LY2 L20 L33 LQ4 LQ9 LR4 LM7 L59 LS4 LH8 LH9.
Check Stock

RJSPHH ls throttle cable kit 36 inch Stainless Steel Braided Throttle Gas Cable Compatible Wire Fit with 97-07 Chevrolet/Chevy LS1 Engine 4.8L 5.3L 5.7L 6.0L

  • COMPATIBLE WITH:97-04 Chevrolet/Chevy LS1 Engines 5.7L&99-07 Chevrolet/Chevy LS1 Engines 4.8/5.3/6.0L..
  • Can easily be cut for a more custom fit, provides wider application..
  • Extended life of the cable with a specially extruded liner.Trimmed to the exact length to fit you need.Adapted to fit most gas pedals and throttle....
  • LS braided throttle cable made of high-quality stainless steel, braided and tubular protective layer, which better protects the smooth and non-binding....
  • We offer 36" braided throttle cable kit 1 years shelf life, any questions in LS braided throttle cable and installation, please share your questions....
Check Stock

A-Team Performance - Fabricated Intake Manifold w/Drive By Wire 102mm EFI Throttle Body - Compatible with LS LSX LS1 LS2 LS6 Black

  • 102mm Black Intake Manifold with EFI Drive by Wire 0° Opening Throttle Body Complete with Gaskets, Hardware, Black Fuel Rails, & Fuel Crossover Line.
  • Compatible with Chevrolet Small Block V8 GEN. III/IV (LS-Based) 4.8 L / 293 in3 (LR4) 5.3 L / 325 in3 (L33, L59, LM4, LM7) 5.7 L / 346 in3 (LS1, LS6) 6.0 L / 364 in3 (LQ4, LQ9, LS2).
  • Compatible With Cathedral Port LS LSX LS1 LS2 LS6 heads.
  • Hardware - 3mm (1/8") thick T6061 Sheet Aluminum construction.
  • Durability - The intake will not bend or flex With Boost Or Vacuum.
Check Stock

ICT Billet LS Gen III Knock Sensor Relocation Brackets Billet Aluminum Compatible with GM LS Gen 3 Engines LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 551216-KN30

  • Relocates LS1 Gen III knock sensors from valley pan to side skirt of the engine block.
  • Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum.
  • Compatible with all LS gen III harnesses and gen III knock sensors.
  • Fits engine RPO codes: LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33.
  • Includes 2 billet aluminum knock sensor brackets and mounting hardware.
Check Stock