Reviews Low Voltage Disconnect 12vs

Blue Sea Systems m-LVD Low Voltage Disconnect

Status light in both m-LVD and Remote Control Switch provides visual warning of low voltage state prior to disconnect.

...Of A Safer Lighting Solution For Your Remote Lighting Needs..
DO NOT Use With AC 120V Or AC 240V - This Is A Bulb Designed For Low Voltage AC DC 12V - Failure To Use Proper Voltage May Cause A Short Circuit Resulting In A Blown Fuse - Please Make Sure This Is The Correct Application Type And Voltage Of Bulb - Please Disconnect All Power Before Installation..

...Of A Safer Lighting Solution For Your Remote Lighting Needs..
DO NOT Use With AC 120V Or AC 240V - This Is A Bulb Designed For Low Voltage AC DC 12V - Failure To Use Proper Voltage May Cause A Short Circuit Resulting In A Blown Fuse - Please Make Sure This Is The Correct Application Type And Voltage Of Bulb - Please Disconnect All Power Before Installation.

...Of A Safer Lighting Solution For Your Remote Lighting Needs..
DO NOT Use With AC 120V Or AC 240V - This Is A Bulb Designed For Low Voltage AC DC 12V - Failure To Use Proper Voltage May Cause A Short Circuit Resulting In A Blown Fuse - Please Make Sure This Is The Correct Application Type And Voltage Of Bulb - Please Disconnect All Power Before Installation.

The battery equalizer is used to maintain the charge and discharge balance between each battery in series connected battery..
The battery equalizer can compensate for the battery in both directions.Reverse polarity protection, low voltage disconnect to provide longer battery life time..
Reverse polarity protection, low voltage disconnect to provide longer battery life time..
Can be connected in series for a long time in the battery, so as to automatically maintain the balance of the battery state..
Intelligent battery voltage equilibrium system keeps batteries in heath and saves battery lifespan. .

Operating Voltage: DC 6 to 18V, Rated current: 30 Amp..
To protect electronics from damaging low voltages and prevent a deep discharge of a battery during an extended power outage, the LVD module will....
Programmable voltage setting for Disconnect and Reconnect (rocker switch set to AUTO). With emergency ON or OFF function, if you want switch output to....
Set rocker switch to AUTO, when the battery voltage drops to less than or equal Disconnect Value and continuously held for 5 seconds, load switch will....
Based on Microcontroller and MOSFET (on status resistance < 0.003 ohm), more precise voltage, smart and long life switch output. Green-red dual color....

Voltage: High current 250 Amp/ Continue Current: 250A normally open/ Universal application 12V/24V, LCD display voltage of two batteries.
Automatically Connection Voltage (Delay 5 seconds) : 13.5V-16V(12V working voltage).
27V-32V(24V working voltage)/ Automatically Disconnect Voltage (Delay 5 seconds) : 12.5V,disconnect immediately if it is below 12.5 V.
Function: 250Amp battery isolator is a primary battery saver, which used to combine two batteries when an alternator is charging (engine running) and isolate them when not charging (engine off) so you can still start your vehicle..
Designed with Small Size, Can Fit Anywhere!/ Wide Use on a variety of vehicles--12V/24V Trucks, ATVs, UTVs, Boats, RVs, Vans, Off-road Vehicle, Caravan & Camping Applications..
Easy to install, Just power wire in, power wire out. No Need to discharge your vehicle's original battery by trying your new equipment off-road.

...er you to change bulbs frequently, save maintenance cost..
【DO NOT Use With AC 120V Or AC 240V】This Is A Bulb Designed For Low Voltage AC DC 12V - Failure To Use Proper Voltage May Cause A Short Circuit Resulting In A Blown Fuse - Please Make Sure This Is The Correct Application Type And Voltage Of Bulb - Please Disconnect All Power Before Installation..

... bother you to change bulbs frequently,save maintenance cost..
【Do Not Use With AC120V Or AC240V】-This is a bulb designed for low voltage AC DC 12-36V,failure to use proper voltage may cause a short circuit resulting in a blown fuse.Please make sure this is the correct application type and voltage of bulb-please disconnect all power before installation..

60A MPPT Charge controllelr, 100% MPPT 60A solar charge controller Intelligent, Max efficiency ≥98.1%, PV utilization ≥99%.Built-in DSP controller with high performance Automatic battery voltage detection 12V/24V/36V/48V, Make sure batteries' voltage more than 12V to boost controller and make sure battery has enough power to Self-detection when connected to the controller..
Fit for 12V/24V/36V/48V battery, USER(can be set Lithium, Lifepo4, Li(NiCoMn)O2)/Flooded/Sealed/Gel battery, User programmable for absorption voltage/Floating voltage/Low voltage disconnect./Load Timer..
Built-in cooling fan, Fan will ON when temperature 003e45℃ and off 003c 40℃,Porous heat dissipation and fan use BEARING technologies increase life UP TO 5000hrs in normal use..
Very detail display with Blacklight---LCD Dispaly PV voltage/output power/Battery voltage/charging current/working mode/Temperature, ☀ TROUBLESHOOTING function and LCD display and can help users not only check the whole system operating data and statuses but also quickly identify system faults and modify parameters..