Reviews Long Pass Filter

Rockville RBG18S 18' 2000W Active Powered PA Subwoofer W/Dsp+Limiter Pro/DJ

  • Built-in Amplifier - With a MOSFET power supply you get improved switching speeds, better performance with less power from the driver, lower gate-to-drain feedback capacitance, lower thermal impedance for higher switching frequencies.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes above the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the LOPRO10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low-Level Inputs - Line level inputs (RCA inputs / low-level inputs) use RCA interconnect cables to link the LOPRO10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Specs – 15.5” x 11” x 3”. If you are short on space, this is a great solution for you. The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. Weight: 13 lbs..
Check Stock

BOSS Audio Systems BX55 2 3 Way Pre-Amp Car Electronic Crossover with Remote Subwoofer Control

  • Front / Rear / Sub Input, Front / Rear / Sub Outputs, Remote Subwoofer Control.
  • Front High Pass Filter 65Hz to 4.5 kHz, Rear High Pass Filter 65Hz to 4.5 kHz.
  • Variable Subwoofer Filter 40 Hz – 4200 Hz, Variable High Pass Filter 65 Hz – 4.5 kHz.
  • Crossover Slope 12 dB / Octave, Variable Subwoofer Phase 0 – 180 Degrees.
  • Variable Bass Boost 0 – 18 dB, Variable Bass Boost Frequency 25 Hz – 250 Hz.
Check Stock

Memphis Audio VIV400.4 SIX FIVE Series 400W 4-Channel Car Amplifier

  • 65 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms) | 200 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode).
  • Front channels: Variable high- or low pass filter (10-5,000 Hz, 24 dB/octave).
  • Rear channels: Variable high-pass filter (10-500 Hz, 24 dB/octave) | Variable low-pass filter (50-5,000 Hz, 24 dB/octave) | Bandpass filter engages both.
  • Variable bass boost (0-18 dB at 45 Hz) on front and rear channels.
  • Dimensions: 10-15/16″W x 2-1/4″H x 8-1/4″D.
Check Stock

ART 351 EQ 31-Band 1/3 Octave Graphic Equalizer

  • The 351 is a single-channel, 31-band, 1/3-octave graphic equalizer with many features: constant Q circuitry with a 3% center frequency accuracy, 20mm center detent sliders, selectable boost/cut range of 6dB or 12dB, active balanced and unbalanced input and output connections, adjustable high-pass filter, adjustable low-pass filter, variable input level control, clip level indicators, ground lift switch, internal power supply, and selectable line voltage switch.
  • The ART 351 Single Channel 31-Band Equalizer features a rugged all-steel chassis that occupies a single 19" rackspace.
Check Stock

Presonus Temblor T10 Powered Studio Subwoofer, Multicolor

  • 10-Inch glass-composite low-frequency transducer.
  • power: 100-120V 50/60 Hz or 220-240V 50/60 Hz.
  • Input gain control (-30 dB to +6 dB, continuously variable) and continuously variable low Pass filter (50 Hz to 140 Hz).
  • Switchable high pass filter removes frequency content below 80 Hz from the full-range signal sent to the main monitors.
  • Momentary footswitch (included) Bypasses the subwoofer, high pass filter, and sub out.
  • Left and right, balanced XLR and ¼” TRS and unbalanced RCA main inputs.
Check Stock

BOSS Audio Systems BX35 Electronic Car Crossover - 3 Way Pre-Amp Fine Tune Your High-Mid-Low Range Speaker Frequencies

  • Front / Rear / Sub Input, Front / Rear / Sub Outputs.
  • Front High Pass Filter 65 Hz to 4.5 kHz, Rear High Pass Filter 45 Hz to 1.6 kHz.
  • Variable Subwoofer Filter 40 Hz – 250 Hz, Variable High Pass Filter 45 Hz – 5 kHz.
  • Crossover Slope 12 dB / Octave, Variable Subwoofer Phase 0 – 180 Degrees.
  • Variable Bass Boost 0 – 18 dB, Variable Bass Boost Frequency 25 Hz – 250 Hz.
Check Stock

Rockville KRYPTON F2 2400w Peak/600w RMS 4 Channel Amplifier Car Stereo Amp

  • Rockville KRYPTON F2 2400w Peak/600w Dyno-Certified RMS 4 Channel Amplifier Car Stereo Amp..
  • Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 2 Ohm: 150 Watts x 4 Channels.
  • 4 Ohm Bridged: 300 Watts x 2 Channel. Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). 2 Ohm: 600 Watts x 4 Channels. 4 Ohm: 400 Watts x 4 Channels. 4 Ohm Bridged: 1200 Watts x 2 Channels..
  • All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers. All channels on the amplifier are bridgeable. Digital Voltage Display on Amp..
  • Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Adjustable Subsonic Filter: 15Hz -40Hz (This filter is on the HPF knob). Adjustable Low Pass Filter: 40Hz – 4KHz. Adjustable Band Pass Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter). Adjustable High Pass (Subsonic) Filter: 15 Hz - 4 kHz.
Check Stock

Rockville Krypton F1 1600w Peak / 400w RMS 4 Channel Amplifier Car Audio Amp

  • Rockville KRYPTON F1 1600w Peak / 400w Dyno-Certified RMS 4 Channel Amplifier Car Audio Amp..
  • Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 2 Ohm: 100 Watts x 4 Channels 003c1% THD+N. 4 Ohm: 70 Watts x 4 Channels 003c1% THD+N..
  • 4 Ohm Bridged: 200 Watts x 2 Channel. Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). 2 Ohm: 400 Watts x 4 Channels. 4 Ohm: 280 Watts x 4 Channels. 4 Ohm Bridged: 800 Watts x 2 Channels..
  • All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers. All channels on the amplifier are bridgeable. Digital Voltage Display on Amp. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry..
  • Adjustable Subsonic Filter: 15Hz -40Hz (This filter is on the HPF knob). Adjustable Low Pass Filter: 40Hz – 4KHz. Adjustable Band Pass Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter). Adjustable High Pass (Subsonic) Filter: 15 Hz - 4 kHz. 2CH/4CH Input Mode Switch. 8 Volt Preamp Circuitry.
Check Stock

BOSS Audio Systems CUBE10 Car Subwoofer and Amp Package – Built-in Amplifier, 10 Inch Subwoofer with Passive Radiator, Remote Subwoofer Control

  • ...600 Max watt amplifier powers the 10” subwoofer.
  • Passive Radiator – A driver unit that has its motor structure (magnet) removed, becomes a passive diaphragm. As a result, there is no Chuffing that you would generally get with a ported box, thus enriching the BASS & making the system more linear.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the CUBE10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Phase Control - Phase control lets you adjust the speaker phase with the amplifier if your speakers or subwoofer are hooked up “out of phase”.
  • Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the CUBE10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Check Stock

BOSS Audio Systems Elite SLIM10 Amplified Car Subwoofer - Low Profile, 10 Inch Subwoofer, Remote Subwoofer Control, for Vehicles Needing Bass with Limited Space

  • ...im design, there are a few installation options.
  • Pulse Width Modulated - PWM simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. Efficiency. Increased reliability.
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s).
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the SLIM10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs.
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the SLIM10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
  • Specs - Dimensions: 13.58” x 10.43” x 3.15”, Weight: 10.45 lbs. Phase control. LED status indicator. Thermal, Short and Overload Protection Circuits. ....
Check Stock