Reviews Line Relay G3bass

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

Yibid LED Integrated Tail Light Compatibility for Honda Grom MSX 125 2014-2018 Motorcycle with 1pcs Orange 2-Pin Turn Flasher Relay Brake Indicator Sequential Lights for MSX125/SF CBR650F CTX700N

  • Brand New Taillight assembly With 1pcs 2-pin Orange Led turn signal flasher relay(B pole=Input，L pole= output---Must in Right connection or Not....
  • Package Included: 1pcs Taillight assembly & 1pcs 2-pin Orange Led turn signal Flasher relay (NO taillight Relay Including!!! you can used your store....
  • Wire Connection: Black Line:Negative ；Red Line:Red Lighting(Brake light) ：Blue Line:Red lighting(Running light) ；2 *Yellow Line:Yellow(Turn....
  • Fitment：Compatibility for HONDA MSX /Grom 125 2013 - 2016 , CB 650 F 2014 - 2015, Compatibility for HONDA CBR 650 F 2014-2015 , Compatibility for....
  • Note！！LED light usually use little bit power, sometimes after you install, the LED light blink so fast or not blink, if you have this issue, you....
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

X10 WS469 Push Button Relay Wall Switch

  • Turn on your ceiling & wall fixtures from anywhere in your house.
  • Push Button Style X10 Relay Wall Switch . Includes X10 updated relay ..
  • 3-Way & Single Pole (On/Off only) Not a dimmer.
  • NOTE: This problem is most likely caused by line noise. The noise on the line stops the X10 signal from getting through so you can't turn the light on. BUT if you turn the light on from its push button, it puts a load across the line that attenuates the noise, so now you can dim or turn off the light. As soon as you turn it off, and remove the load, the noise pops back up. You need to determine the source of the noise and filter it..
Check Stock

Yibid LED Integrated Tail Light Replacement for Honda Grom MSX 125 Motorcycle 2014-19, Brake Indicator Sequential Lights for MSX125/SF CBR650F CTX700 CTX700N, Smoke len with 1pcs 2-Pin Flasher Relay

  • Brand New Taillight assembly With 1pcs 2-pin Black Led turn signal flasher relay(B pole=Input，L pole= output) ；No instruction! Need to install skills，Professional installation is Recommended.
  • Package Included: 1pcs Taillight assembly & 1pcs 2-pin Black Led turn signal Flasher relay (NO taillight Relay Including!!! you can used your store one) Fitment :For MSX125 CBR650F CTX700 CTX700N.
  • Wire Connection: Black Line:Negative ；Red Line:Red Lighting(Brake light) ：Blue Line:Red lighting(Running light) ；2 *Yellow Line:Yellow(Turn Left/Right Light) ；YOU CAN TEXT IT BEFORE INSTALL！.
  • Fitment： Compatibility with/Replacement for HONDA MSX /Grom 125 2013 - 2016 , CB 650 F 2014 - 2015, HONDA CBR 650 F 2014-2015 , HONDA CTX 700 N 2013 - 2015.
  • for ‘17-18’ Compatibility with/Replacement for Honda Grom Please check your taillights bucket and the lisitng picture（4&5）,Some bikes may not the perfect fitment need to modify!!!.
  • Note！！LED light usually use little bit power, sometimes after you install, the LED light blink so fast or not blink, if you have this issue, you may need LOAD RESISTOR to put between the LED lights and POSITIVE, usually go around 6 ohm LOAD RESISTOR will,make it work, however we do not carry any load resistors,please purc....
Check Stock

Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10

  • 【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
  • 【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
  • 【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
  • 【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • 【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
Check Stock

K-Head Repeater Box RPT-2K Relay Walkie Talkie K-Head Two Way Radio Repeater Box for Baofeng UV-5R DM-5R GT-3TP Radio

  • 【Plug and Play】No power supply needed. There is no need to change any part of the original walkie-talkie, just take two handheld walkie-talkies.....
  • 【Parameters】Portable relay box is made of ABS. Plug: K head, color: black, whether it is two-way: yes, line length: both sides are 90cm/35.4in....
  • 【About Two-way Relay Box Plug】 Two-way relay box plug does not divide input/output, two-way relay box forwarding mode: A machine receives B....
  • 【Two-way Forwarding】When the A machine receiver, the B machine transmits. When the B machine receives, the A machine launches. The two-way....
  • 【Audio Trigger Mode】This relay box is an audio trigger mode. When using it, the volume of the intercom as a receiving signal should be adjusted to....
Check Stock

ALMOCN 6Pcs DC 5V 1 Channel Relay Module With Optocoupler Isolation Support High or Low Level Trigger

  • The Relay Board Maximum load: AC 250V/10A, DC 30V/10A.
  • Using SMD optocoupler isolation, strong driving capability, stable performance..
  • Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications..
  • Fault-tolerant design, even if the control line is broken, the relay will not move..
  • Wide Application,The relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
Check Stock

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

  • It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
  • Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
  • RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
  • With optical coupling isolation, triggering more reliable, more stable..
  • EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..
Check Stock

Over-Voltage Under-Voltage Protection Monitoring Relay Circuit Breaker Adjustable Control Module DC 12V/24V/36V/48V(DC24V)

  • Voltage RegulationWhen a faulty line occurs, the voltage protection relay can adjust the overvoltage value and the action time, and record the fault for more flexible use..
  • Real-time MonitoringThe voltage protection relay can monitor overvoltage and undervoltage faults in real time and take protective measures in time..
  • LED DisplayThe voltage protection relay includes two sets of normally open and closed contacts, and the two indicator lights respectively indicate different working states..
  • Rail MountingThe voltage protection relay adopts a standard modular structure and is mounted on a 35mm rail without additional auxiliary power..
  • Our ServiceWe strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..
Check Stock