Reviews Light Aggregate Concrete Block

Mutual WF200 Polyethylene Woven Geotextile Fabric 300 Length x 6 Width

Woven geotextiles are used to hold soil in place, and can also be used under rip rap, gabions or precast block.
Woven geotextiles area time and money saving alternative to traditional methods using graded aggregate or sand filters.
They prolong the surface life and stabilize the foundation while providing a rugged separation layer between aggregate and subgrade.
Measures 6-feet width by 300-feet length.

EPOXY PATCHING SYSTEM: Permanent epoxy patching system seals cracks and holes and smooths over pitted concrete surfaces.
SUPER STRONG: Restores and even exceeds the strength of the original concrete.
Withstands traffic and even loads of up to 10,000 pounds.
COVERAGE: 50-pound, 5-gallon pail covers up to 100 square feet with a 1/8-inch thick coat.
APPLICATION: Three-part mixture includes epoxy, hardener, and aggregate.
Apply with a trowel, hand tamp, or roller for even coating.
USES: For use on walkways, staircases, streets, walls, ramps, and any indoor or outdoor concrete surface.

...-icing salts & chlorine. 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....

Pre-measured adhesive of polyester resin base, quartz sand and benzoyl peroxide hardener.
Sand and aggregate mixture is closest to natural concrete.

Breathable two-part waterborne epoxy coating, Decorative flakes, Anti-slip aggregate, Cleaner/Degreaser included.
Professional grade floor covering, Easy to install, No acid etching or mechanical prep necessary in most cases, Clean with degreaser included, mix and apply with roller, Scatter flakes in wet epoxy.
Epoxy coating breathes allowing moisture vapors to pass through eliminating blistering and peeling, Resistant to automotive fluids, hot tire lift, Good adhesion to concrete and wood.

Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
Uniform synthetic diamond grit bonded over a durable steel platform.
Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
Recommended cutting speed is from 150 to 300-RPM.

Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
Uniform synthetic diamond grit bonded over a durable steel platform.
Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
Recommended cutting speed is from 150 to 300-RPM.

Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
Uniform synthetic diamond grit bonded over a durable steel platform.
Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
Recommended cutting speed is from 150 to 300-RPM.

BEAUTIFUL WET LOOK SEALER Works on exposed aggregate, stamped, colored or decorative surfaces.
WILL NOT SIGNIFICANTLY DARKEN MOST SURFACEs when it dries. Does not look like you sprayed water on it. Resists chemicals and oil, Durable, Clear & Non-Yellowing..
PLEASE READ COMPLETE PRODUCT DESCRIPTION: Not for polished GRANITE OR MARBLE.
SPRAY, BRUSH OR ROLL on concrete, pavers, slate, driveways, garage floors, patios, masonry, brick warehouse floors.
MADE IN THE USA. Professional Results VERY low odor dries in hours..

...lon (treats 300-600 feet) or 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....