Reviews Lag Screw Kit

1/4 Hex Lag Bolts 1 1-1/2 2 2-1/2 3 JROUTH 155PCS Black Oxidized Hex Lag Screws Heavy Duty Wood Screws Washers Assortment kit Stainless Steel 18-8 304

  • 【Certified Stainless Steel】Black lag bolts are made from 18-8 (304) stainless steel and coated with black oxide, which is certified, good look, strength and corrosion resistant.These bolts well made and you will keep them for future needs..
  • 【Various Sizes】Lag screws kit includes 5 different most common used sizes: Diameter are all 1/4".
  • Length from 1'' to 3''. Thread Type are all Coarse (standard).
  • Quantity: 155 pieces screws and washers. Refer to Figure 2..
  • 【Project Center】These wood screws assortment kit are excellent for exterior household and industrial applications such as deck buildings, gazebos, trusses and other wood connections.We used these as the fasteners for steel banding trim on a custom barbwe designed and built.Turned out perfectly!.
  • 【Choice for Heavy Duty Applications】These lag bolts are ideal used for securing wood in heavy duty applications that standard wood screws cannot support the load feature deep wood screw coarse threads for superior holding and prevent stripping in the material.
  • Can be applied in even severe environment. Often using with washer which distribute the pressure of the head evenly so that to prevent pull through..
  • 【Guarantee in JROUTH】Our hex lag screws undergo rigorous inspections to ensure they....
Check Stock

Stainless Steel 316 Lag Screws Hex Head Lag Bolts 1/2 x 1-1/2 Qty 250

  • Stainless Steel 316 Lag Screws Hex Head Lag Bolts 1/2".
  • Commonly referred to as a lag screw or lag bolt.
  • Features the sharp cutting threads of a wood screw.
  • Commonly used in heavy duty carpentry applications including lumber framing and anchoring equipment to wood such as machinery and large vices.
  • 316 stainless steel is highly corrosion and rust resistant.
Check Stock

48 Pack Swage Lag Screws Left & Right for 1/8\ Cable Railing kit,T316 Stainless Steel Stair Deck Railing Wood Post of Cable Railing Kit, Decking Railing Hardware, DIY Baluster Kit

  • 【LEFT & RIGHT DESIGN】 With the Left hand lag screws and Right hand Lag Screws design, it can rotate wire rope in the same direction, which resolves the problem of twisting the wire rope. Products without Left & right design might damage the cable. The wrench multi-tool is handy, it will help you drill the lag screw into the wood easily..
  • 【PROTECTOR SLEEVES】 These stainless steel protector sleeves will prevent the wire cable from wearing into the post, and maintain the cable rail tension for preventing wire rope vibration..
  • 【COMPATIBILITY】 These Cable Railing Kits are suitable for 1/8" diameter wire rope cable railing system, perfect for DIY your own wood baluster post stair or decking railing project, good for indoor or outdoor applications..
  • 【HIGH-QUALITY 】 Made of premium stainless steel for weather-tough durability, super-strong resistance to rust and corrosion, low maintenance and lasting beauty..
  • 【WHAT YOU WILL GET】 The cable railing kit includes 30 PCS left handed thread swage lag screws, 30 PCS right handed thread swage lag screws, 80 PCS protector sleeves, 2 PCS drill bits (The 6.5mm drill bit is used for drilling the protector sleeves holes, and the 5mm drill bit is used for drilling the lag screws holes), 1 PCS wrench..
Check Stock

1000LED 4 Inch Round Pole Bracket Tenon Adapter, Tenon Pole Bracket, Single Vertical Bracket Adapter for LED Street Light, Shoebox Light

  • ...sual effect according to different of occasion.String light hanging wire can present very good effects in outdoor and indoors..
  • 【Enough Accessories】This outdoor string light kit provide almost all of the kit you need, including 180 feet Stainless Steel 304 Cable.
  • 4 Pcs M5 Turnbuckle,4 Pcs Attached Snap Hook,4 Pcs Screw Eyes Lag Thread,8 Pcs Eye Straps,12 Pcs Adjustable Locking Device,16 Pcs Lag Screw,16Pcs Plastic anchors,130PCS Black Twist Ties,1*user manual..
  • 【Service Support】We are committed to providing customers with high quality products and comprehensive after-sales service.All accessories in globe string lights wire are reliable for long term and convenient uses and they are backed with a 100% money back guarantee.Whether it is product quality or usage problems,you can contact us at any time.we will reply within 24 hours,all guarantees the interests of customers are our aim..
Check Stock

Ingpro 80 Pack 316 Stainless Steel Left&Right Handed Thread Swage lag Screws for 1/8\ Decking Cable Railing Kit/Hardware,Wood Post Balusters (40 Pairs)

  • This cable railing kit（Single lag screw） made of high quality Marine Grade T316-Stainless Steel，It is anti-rust、 durable and easy to maintain；.
  • The angle of this professional Single-Screw cable railing hardware 0 to180 degrees could be free adjusted；So they can be used to all kinds of complex cable railing system：railing of stairs，deck railing and Garden fence…；.
  • This cable railing hardware applies to standard 1/8" inch cable（OD）， Hydraulic crimper is required to connect this kit with the cable and the 4-6# dies is suitable.
  • The length of the screw is 2 inch, Pre-drilling screw holes is required before installation；The turnbuckle fully extended length is 10 inch and fully shortened length is 6-3/4 inch (Size details are shown in the figure).
  • This kind of cable railing fitting advantage：high quality、easy to install and looks clean..
Check Stock

CONFAST 1/2\ (Inside/Screw 1/2\ - 13) Double Expansion Anchor (20 per Box)

  • Allows for lag screw bolts to be installed into concrete, brick and block.
  • Inserts into a hole by tapping with a hammer until flush.
  • Lag screw expands the lag shield against the walls of the hole.
  • Drill hole with masonry drill bit based on diameter on anchor.
Check Stock

Hard-to-Find Fastener 014973269470 Lag Expansion Shields, 1/4 Short, Piece-12

  • Expansion shield anchors for use with lag screws are designed to anchor into concrete, brick, and block..
  • Expansion shield anchors consist of pre-assembled two-part expansion shields..
  • These anchors expand as a lag screw is fastened through the anchor..
  • These anchors feature very precise tapered internal threading to permit easy turning of the lag screw..
  • Zinc plating adds a layer of corrosion resistance to the anchors..
Check Stock

Werkzeug Damaged Stripped Screw Extractor Set for Broken Screw, All-Purpose HSS Broken Bolt Extractor Screw Remover Set with Magnetic Extension Bit Holder & Socket Adapter (22 PCS )

  • Damaged Screw ExtractorWerkzeug screw extractor is made of high quality High-Speed Steel 4241. High hardness, durable and easily remove damaged screws.
  • In one stepThe stripped screw extractor set is included two extension bit holder. Can remove in one step, do not need to conversion the extractor or adjust the chuck.
  • Extremely VersatileThe stripped screw extractor kit is includes 20 pieces of stripped screw extractor in 10 different sizes to satisfy all you demand. Suitable for any sizes screw or bolt.
  • MultipurposeSuitable for allen bolts, machine screws, lag bolts, wood screws, hex bolts, sheet metal screws and other screws.
  • ImportantIt is best to use electric hand drill, can not be used the hammer drill mode! Must be low speed during use!.
Check Stock

Loboo Idea Speed Out Screw Extractor Drill Bits Tool Set Broken Damaged Bolt Remover Guide Set Broken Easy Out Fastener Kit (5 Pieces, HSS 4341# Silver)

  • Designed for Screw & Bolt Extracting: Each bit has dual head designs, one is used to drill a hole in the middle of the the damaged screws or bolt with the drill end, the other is used to extracting it. The special design helps you grab and remove the screws precisely and easily in 10 seconds or less..
  • H.S.S 4341 Material: Loboo Idea stripped screw extractor is made of high quality H.S.S 4341 material, has 63-65 HRC hardness which is harder than most of other similar products. Durable and solid, suitable to removes even the most stubborn stripped, damaged, embedded, rusted and painted-over screws and bolts. Best gift for any craftsman..
  • Multi Purpose: 5 different sizes of bits (#0, #1, #2, #3, #4) are included in package of stripped screw remover kit and #0 is a gift provided for extra using. All is for ensuring that the screw extractor kit can meet all of your needs. Great for removing stripped, broken head, rusted, unscrew, free-spinning and deck screws or bolts..
  • Easy to Use: 3 simple steps: 1. Drill out, 2. Flip Bit, 3. Extract. Just no other tools needed but a drill, select a smaller bit than the damage screw, you can easily remove the screw. Note: please make sure to run the drill in reverse during the process..
  • Wide Application: The screw and bolt ....
Check Stock

Lag Bolt Kit for Mounting A TV Into Wood Or Concrete - Includes Heavy Duty Bolts Fischer Concrete Anchors and 2 Drill Bits

  • Re-mounting, but lost your old hardware? Don't buy another mount! This kit includes everything you'll need for wood or concrete installs..
  • We don't screw around: Our lag bolts are custom-hardened to prevent snapping or breaking..
  • You trust us? We trust Fischer. Included in this kit: 4 of their concrete-rated anchors (UX10 x 60R).
  • Which size drill bit you need for mounting to wood or concrete? Trick question: They're both included..
  • Plays well with others: This kit was designed for ECHOGEAR mounts, but will work for whatever mount you've got..
Check Stock