Reviews Isolated Switch

AEDIKO 4pcs DC 5V Relay Module 2 Channel Relay Board with Optocoupler Support High or Low Level Trigger

  • Normally Open Interfaces Maximum Load : AC 250V/10A, DC 30V/10A.
  • 2 Channel Relay Module 5V Comes with High-Current Relay,Trigger Current : 5mA.
  • 5V Relay Module is 2 Channel Isolated, Each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
  • Relay Module Designed With Fault-Tolerant , Even If The Control Line Breaks, The Relay Will Not Move.
  • With Optical Coupling Isolation,Triggering More Reliable and Stable.
  • 2 Channel Module Equipped With Screwed Terminal Plate and Fixed Bolt Holes,Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.
Check Stock

AIMS Power 5000 Watt 12V DC to 120V AC Industrial Pure Sine Power Inverter Industrial

  • 5000 Watt continuous power, 10000 Watt surge, 12 Volt DC input, Pure sine wave.
  • 60hz or 50hz switch, Highly efficient improved output at low voltage, 2-GFCI Dual Outlet.
  • Direct connect AC Terminal Block Connector and cable for remote on/off switch, Isolated ground & neutral.
  • Short circuit protection (GFCI and AC Breaker), On/off switch, 5 Function Protection LED indicator.
  • AC Breaker, Dual cooling fans thermally controlled, GFCI Outlets rated at 20A per block.
Check Stock

Blue Sea Systems Battery Switch m-Series Selector, Black, 6007200

  • Blue Sea Systems Battery Switch m-Series Selector, Black, part number 6007200, is a Selector 4 Position switch. Switches isolated battery banks to all loads or combines battery banks to all loads.
  • IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protected—safe for installation aboard gasoline powered boats.
  • Make before break contact design allows switching between battery banks without power interruption.
  • Continuous Rating: 300A, Maximum Voltage: 32V DC.
Check Stock

CR Magnetics CR9380-PNP-M PNP Transistor Output Split Core Current Switch with Mounting Case, Normally Open, 30 VDC

  • Current switch for monitoring current flow.
  • Current carrying wire is routed through an aperture.
  • Electrically isolated normally open (NO) switch.
Check Stock

LoveRPi Compact PoE HAT with PWM Fan Controller for Raspberry Pi 4

  • COMPACT RASPBERRY PI 4 POE HAT: Ideal for non-grounded installation, this NON-ISOLATED PoE HAT features optimized footprint. Must be used with a standards compliant IEEE 802.3af PoE or 802.3at PoE+ switch that complies with Section 33.4.1 for power sourcing equipment (PSE) electrical isolation. "Passive PoE" (DC 24V or 48V) is not standards compliant and may cause damage to equipment if connected improperly. Some Ubiquiti switches are not properly isolated and require isolated PoE HATs..
  • GROUND LOOPS WARNING: Do not use this device with grounded USB peripherals, HDMI displays, and attachments. Please use the professional PoE model with isolation transformer to prevent electrical loops. In non-controlled PoE applications, ALWAYS use the professional PoE model..
  • INTEGRATED PWM FAN CONTROLLER: Based on the EMC2301 SMBus compliant fan controller, this PoE HAT is fully programmable over I2C to control standard 4-pin PWM fans. Set user-space or device-tree based temperature or event triggers for complete fan control from off to maximum RPM. Fan speed tach also provides stall detection, spin-up control, and ramp rate control with 1% accuracy from 500-16K RPM..
  • VENTILATED CASE WITH FAN HIGHLY RECOMMENDED: Do not use this product in an enclosed case without acti....
Check Stock

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

  • It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
  • Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
  • RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
  • With optical coupling isolation, triggering more reliable, more stable..
  • EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..
Check Stock

AIMS Power PWRIG200012120S 2000W Pure Sine Inverter Continuous 4000W Surge Peak Power 12V DC Input 60hz or 50hz Switch 1 GFCI Dual Outlet

  • 2000W continuous power, 4000W surge peak power, 12 Volt DC input, 60hz or 50hz switch.
  • Highly efficient - improved ouptut at low voltage, 1 GFCI Dual Outlet.
  • Connector and cable for remote on/off switch, Isolated ground & neutral.
  • Short circuit protection (GFCI and AC Breaker), On/off switch, 5 Function Protection LED indicator.
  • AC Breaker, Dual cooling fans thermally controlled, Internal blade fuse protection, Instruction manual.
Check Stock

Off-Line Controller,DDCSV3.1 3 Axle Off-Line Controller with Emergency Stop Function Handwheel Kit,Strong Anti-Interference Ability, Long-Distance Transmission

  • [SMART]Support the origin and Limit share the same Input ports.The controller only support NPN type limited switch.Support the operation of quickly specify the running position and ''Power Cut'' recovery. Data is automatically saved..
  • [PROFESSIONAL ] 16 opto isolated digital inputs,3 opto isolated digital outputs.3axle motor Control.Differential Pulse and direction output signal,maximum.500Khz per axle..
  • [EASY TO USE]ARM9 main control chip,FPGA core algorithm chip.5 inches TFT screen, resolution ratio: 480x272,17 operation keys. Analog spindle control 0-10V spindle control (can be modified as PWM output)..
  • [HIGH QUALITY ]Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version..
  • [WIDELY USED] Applications: CNC machine tools, printing machinery and other zero correction and signal segmentation..
Check Stock

Voodoo Lab Pedal Power X4 Isolated Power Supply

  • Ultra-compact chassis easily mounts to the smallest pedalboards.
  • Unique DC transformer topology provides optimum platform for QUIET switch-mode power.
  • Includes power cables, Universal input power adapter with detachable AC line cord, and 3M dual lock for mounting.
Check Stock

Voodoo Lab Pedal Power X4 Isolated Output Expander Kit

  • Adds four 9V isolated outputs to an existing pedal power.
  • Powered from any Voodoo Lab pedal power 12V 400mA output.
  • Ultra-compact chassis easily mounts to the smallest pedalboards.
  • Unique DC transformer topology provides optimum platform for QUIET switch-mode power.
Check Stock