Reviews High Temperature Nozzle

Heat Gun, Preciva 2000W Hot Air Gun Kit with 3-Temp Settings (140℉-1112℉), Extension Rod and 5 Nozzles, Overload Protection Function for PVC Shrinking and Paint Removing.

  • ...euipped with high power of 2000W, which could provide much more high power, could be heated up quickly. Also comes with overheat protection function, it will be automtically power off if it was overheating. This function could offer a long service life of the heat gun..
  • [3 Temp Settings & 5 Nozzles]: There are Three temperature settings, which are 60℃(140℉), 350℃(662℉), and 600℃(1112℉). Three temperature modes could meet your need. Packed with 5 nozzles, Concentration nozzle, Reflector nozzle, Flat nozzle, BBQ nozzle and Burning Nozzle..
  • [With Extension Rod]: Comes with a extension rod, which could be used for burning the grass. Adopt mica board electric heating core, with excellent high temperature resistance and insulation performance. The hot air gun has a motor and dial protection design. No matter which gear is used during use, it needs to be pushed back to the zero gear again, and then pushed to the required gear..
  • [Wide Applications & Durable]: This heat gun could be used for stripping old paint and gloss, removing self-adhesive labels, vinyl wallpaper.
  • and BBQ etc. The stainless steel nozzle and ABS plastic handle makes it durable..
Check Stock

Professional Heat Gun 1600W 122℉~1112℉(50℃~600℃) - Adjustable 7 Heat Levels with 3 Temp-settings, 4 Nozzle Attachments, Unique Cooling Mode, Soft Rubbrized Handle(Working Time Over 500 Hrs) - HGP73AC

  • ▲Last longer than most competitors – Working Time over 500 hours in max temperature(data from lab).
  • ▲7 LEVELS PRECISE TEMPERATURE CONTROL WITH 3 FLOW MODES – Easy rear dial for temp selection[I: 122℉(50℃)-250L/min.
  • III:194℉- 1112℉(90℃- 600℃)-500L/min].
  • Mode II and III equipped with  1-7 level temperature control, more accurate and more selective to satisfy all your utility.
  • ▲STURDY WITH OUTSTANDING PERFORMANCE – Strong power 1600w provides quickly heat up to the maximum temperature 1112℉(600℃) in seconds.
  • Professional heater could keep running around 500 hours in max temperature(data from lab).
  • ▲122℉(50℃) COOLING MODE & OVERLOAD PROTECTION FOR LONGER USE – Special designed cooling mode running at 122℉(50℃) lets you quickly cool down the material in high temperature after heat up.
  • Professional built-in overheating protection protect the heat gun well, provide 3 times longer use than others.
  • ▲FOUR NOZZLE ATTACHMENTTS & COMFORTABLE GRIP – Various attachments can extend your utility by heat gun.
  • You can easily strip paint, bend pipes, light up charcoal, shrink PVC, remove rusted bolts, mold plastics as well as drying and thawi....
Check Stock

Creality 10 Packs 3D Printer Hardened Steel MK8 Nozzles, Upgraded Tungsten All Metal Extruder Nozzles 0.2mm, 0.3mm, 0.4mm, 0.5mm, 0.6mm for Creality Ender 3 Ender 3 V2 Ender 3 pro CR-10

  • ...K8 extruder nozzles are made by paramount hardened tungsten steel, with longer lasting time than the normal brass nozzle. The hardness is beyond HRC60, can reduce the abrasion to the inner and outer of the nozzle during long time printing, more heat-resistant and more durable than ordinary brass nozzle..
  • [Super High Temperature Resistance] - The max temp of this hardened tool steel nozzle could reach at 450c, suitable for 3D printing at high temperature, compatible with material such as PLA, ABS to carbon fiber, even PEEK..
  • [High Precision More Than Your Imagination] - Keep stable temperature during printing, let the filament out evenly, create more perfect printer item than normal metal nozzle. Also with higher print speed in same print precision. Avoid clog during printing, easy to clean. Made with centering CNC precision automatic lathe and with one-time forming technology, make sure the input and output holes are concentric and the interior of nozzle is smooth without burrs..
  • [Applicability & Compatibility] - Our Creality Nozzles are compatible with almost all FDM printer, also fits for MK8 heating block. Our tungsten nozzles are also designed for 3D Printer Makerbot Creality Ender 3 series and CR-10 series 3D printer, MK8 Makerbot Reprap Prusa I3, ....
Check Stock

Tattoos

  • ... nozzle is too far from the magnetic plate, the printed model will not stick to the magnetic plate. Please watch the leveling manual or video carefully.
  • ✪【HIGH PRECISION PRINT HEAD】: 3D printer's nozzle uses a professional all-metal nozzle to ensure the best printing temperature and minimize the risk of printing errors. In addition, the printers kit has a layer resolution of up to 0.05 mmr, guarantees the accuracy of the print model. Dual fans provide better heat dissipation for faster and more even modeling.(Note: This mini 3D printer doesn't have the Resume Print Function, if there is a power failure it will print from the beginning .).
  • ✪【FAST HEATING AND PRINTING】: X1 printers machine are much easier to use for beginners. It comes with a unique key system that allows you to start, stop and easily control the printing process. The nozzle is heated evenly, it only takes 5 minutes, and the temperature of the nozzle can reach 180 degrees, which can meet the temperature requirements of the PLA material pressure. (Do not touch the nozzle with your hands, if the nozzle has excess filaments, please remove it with the help of other tools).
Check Stock

Makita PR00000034 1-3/8\ Welding Nozzle

  • WELDING NOZZLE SUPPORT: PVC floor round welding nozzle with wheels, can be used with welding wire, with rollers to guide the welding seam straighter..
  • WELDING NOZZLE WITH WHEEL: The welding nozzle with wheel can be directly fixed on the hot air gun. When there is a wheel, the wheel can be directly attached to the gap, and the gap can be filled evenly along the line of the gap, which can solve the manual filling of the weld. The filling is not straight..
  • WELDING ROD SPECIFICATIONS: Hot Air Gun Welding Nozzle can use 3mm/4mm/5mm..
  • WELDING NOZZLE WITH WHEEL ADAPTER: 8mm inner diameter of the heat gun nozzle, which can be matched with any other welding nozzle with an outer diameter of 8mm..
  • MATERIAL: 304 stainless steel alloy, with good corrosion resistance and heat resistance, can withstand high temperatures of 800-1000℃, will not rust, oxidize, and deform under high temperature for a long time. It is an ideal accessory for plastic welding..
Check Stock

Conair CompleteSteam 1100 Watt Handheld Fabric Garment Steamer, All White

  • 1700W HIGH POWER - Put the water inlet pipe in a bucket, turn on the switch and hold the trigger of steam gun. Fast steams out only need 15 seconds. No built-in water tank design makes the steamer lightweight to carry and don't have to constantly refill the tank..
  • HIGH TEMPERATURE STEAM - Through the high-pressure high-temperature steam and strong spray force, the cleaning job is done perfectly. Easy to achieve natural oil removal, remove stains quickly and strongly, create a clean and comfortable living space..
  • HIGH PRESSURE STEAM - Our hand-held pressurized steam cleaner can release about 3~5 BAR of high pressure steam, which is equivalent to 6~10 kg of pressure acting on 1 cm^2, easily spraying oil, dust, stains and so on..
  • 360º CHEMICAL FREE CLEANING - Our steam cleaning machine features extended 2.5m steam pipe and extended elbow nozzle that combine high-temperature steam to penetrate deep into the corners of the gap for easy cleaning..
  • WITH STEAM HUMIDITY ADJUSTMENT - There is a Knob that can controll the water inlet, to reach different steam water content. Equipped with 1.2m silicone water inlet pipe and no water tank built-in..
  • PRODUCT WARRANTY & FREE PARTS REPLACEMENT - If you find any parts are damaged after receiving product, just contact us, ....
Check Stock

The Cheap Detective

  • ... nozzle is too far from the magnetic plate, the printed model will not stick to the magnetic plate. Please watch the leveling manual or video carefully.
  • ✪【HIGH PRECISION PRINT HEAD】: 3D printer's nozzle uses a professional all-metal nozzle to ensure the best printing temperature and minimize the risk of printing errors. In addition, the printers kit has a layer resolution of up to 0.05 mmr, guarantees the accuracy of the print model. Dual fans provide better heat dissipation for faster and more even modeling.(Note: This mini 3D printer doesn't have the Resume Print Function, if there is a power failure it will print from the beginning .).
  • ✪【FAST HEATING AND PRINTING】: X1 printers machine are much easier to use for beginners. It comes with a unique key system that allows you to start, stop and easily control the printing process. The nozzle is heated evenly, it only takes 5 minutes, and the temperature of the nozzle can reach 180 degrees, which can meet the temperature requirements of the PLA material pressure. (Do not touch the nozzle with your hands, if the nozzle has excess filaments, please remove it with the help of other tools).
Check Stock

Enertwist 1500W Dual Temperature Heat Gun Kit with 4 Nozzle Attachments for Shrink Wrapping, Paint Removal, Rusted Bolt Stripping, Wire Shrinking, Crafting, ET-HG-1500R

  • ★ Dual Temperature★ 2 Temp settings 662℉& 1112℉(350℃ & 600℃) features High/ Mid/ Off control [ II: 500 L/min,I: 300 L/min, Off] can satisfy all your utility..
  • ★ Powerful & Reliable★ Heavy duty heating gun with 12.5 Amp motor heats up to maximum temperature 1112℉(600℃) quickly in few seconds and performs stable. Professional heater gives outstanding performance by keeping running 500 hours in max temperature (data from lab)..
  • ★ Ergonomic & Safety★ Ergonomic design for comfort and balance to reduce fatigue, integrated hands free support stand allows the gun sit upright for safe hand-free operation. With professional built-in overload protection prevents hot air gun from over heating due to misuse..
  • ★ Versatile Accessories★ 4 Nozzle deflectors extend heat gun utility, Reduction nozzle for welding plastics, solering/ de-soldering, shrink wrapping, loosening seized bolts & nuts. Glass protection nozzle for paint removing or adhesive stripping neat heat-sensitive materials. Wide jet surface nozzle for paint or adhesive removal. Reflector nozzle for heat shrinking tubing, shaping PVC tubes, thawing frozen pipes..
  • ★ What You Get★ Enertwist Electric heat gun and 4 nozzle attachment kit, user manual, warranty card. Any Issues kindly....
Check Stock

Introduction to Play Analysis

  • ... nozzle is too far from the magnetic plate, the printed model will not stick to the magnetic plate. Please watch the leveling manual or video carefully.
  • ✪【HIGH PRECISION PRINT HEAD】: 3D printer's nozzle uses a professional all-metal nozzle to ensure the best printing temperature and minimize the risk of printing errors. In addition, the printers kit has a layer resolution of up to 0.05 mmr, guarantees the accuracy of the print model. Dual fans provide better heat dissipation for faster and more even modeling.(Note: This mini 3D printer doesn't have the Resume Print Function, if there is a power failure it will print from the beginning .).
  • ✪【FAST HEATING AND PRINTING】: X1 printers machine are much easier to use for beginners. It comes with a unique key system that allows you to start, stop and easily control the printing process. The nozzle is heated evenly, it only takes 5 minutes, and the temperature of the nozzle can reach 180 degrees, which can meet the temperature requirements of the PLA material pressure. (Do not touch the nozzle with your hands, if the nozzle has excess filaments, please remove it with the help of other tools).
Check Stock

Genesis GHG1500A Dual Temperature Heat Gun Kit With Fast Heat High And Low Settings 572F/1000F, Air Reduction Nozzle, Reflector Nozzle, And Two Deflector Nozzles with 2 Year Warranty

  • 1500/750 watt heat gun with powerful 12.5 amp motor.
  • High and low temperature settings for versatility.
  • Deflector nozzles protect glass and other surfaces.
  • Reflector nozzle speeds Thawing of pipes. 3-Position rocker type switch for high temperature, off and low temperature.
  • Includes: (2) deflector nozzles, (1) reflector nozzle and (1) air reduction nozzle.
  • Use the Genesis heat gun for lighting Charcoal grills without the need for Smelly lighter fluid.
Check Stock