Reviews Heavy Load Power Relay

3v Relay Board Raspberry Pi Arduino Relay Module 1 Channel Opto-Isolate High Level Trigger for IOT ESP8266 Microcontrollers Development Board

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Main Specification】- The 3v Relay 1 Channel power switch module compatible with 10A 250VAC and 10A 30VDC load.4pcs * 2.5 mm Fixed Bolt Hole..
  • 【Adopted Optocoupler Isolation】- 3V/3.3V power relay module supports photocoupler isolation control and dual power supply input ensure high anti-interference ability. Fast response time less than 20ms and long life time up to 100,000 times snap action with diode freewheel protection..
  • 【Jumper Caps】You can select whether the relay and the signal use the same power supply or not by removing the jumper caps on the pins. And It is better to share the same power supply, because that is more convenient for using..
  • 【Wide Application】- These 3v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/IOT/ ESP8266 module etc..
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

3V Relay Power Switch Board, Icstation 1 Channel Optocoupler Module Opto Isolation High Level Trigger for IOT ESP8266 Development Board (Pack of 5)

  • 【Optocoupler Isolator】 3V/3.3V power relay module supports photocoupler isolation control..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【Jumper Caps】You are free to select whether the relay and the signal share the same power supply or not by removing the jumper caps on the pins or not. It is recommended to share the same power supply, because that is more convenient for using..
  • 【Rotate Screw Terminals】 The external connection adopts a rotary crimping terminal, which makes the crimping more firm, and has fixed mounting holes for easy installation..
  • 【30VDC 250VAC Load】The power switch is compatible with 10A 250VAC and 10A 30VDC load..
Check Stock

Shuian 10 Pcs 3V Relay Power Switch Board, Songhe DC 1 Channel Optocoupler Relay, High Level Trigger for IOT ESP8266 Development Board.

  • The 3v Relay 1 Channel power switch module compatible with 10A 250VAC and 10A 30VDC load.4pcs * 2.5 mm Fixed Bolt Hole..
  • 3V/3.3V power relay module supports photocoupler isolation control and dual power supply input ensure high anti-interference ability. Fast response time less than 20ms and long life time up to 100,000 times snap action with diode freewheel protection..
  • Equiped with high-current relay, AC250V 10A.
  • DC30V 10A,each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Support dual power supply input ensure high anti-interference ability,high reliability of photoelectric isolation protection,The external connection uses the rotary crimping terminal, causes the wiring to be more solid..
  • You are free to select whether the relay and the signal share the same power supply or not by removing the jumper caps on the pins or not. It is recommended to share the same power supply, because that is more convenient for using..
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

NTHREEAUTO 2 Pin Electronic Flasher Relay, Adjustable 12V Relays Fix for LED Turn Signal Hyper Flash, Universal

  • Speed Adjustable - Fix motorcycle turn signal hyper flash, allow LED light to blink at the normal rate, anticlockwise turn faster, clockwise turn slowly..
  • Parameter - Flashing Frequency: 50 times/min to 200 times/min. Operating Voltage: 12V (11V-15V). Switch Power: 0.02A to 12A. Working Temperature: -40°C to +80°C. Max Power: 42W, means that the power of all LED bulbs must be low than 42 W. If more than 42 W, may required install load resistors..
  • Waterproof - Turn signal flasher relay is waterproof design, stable and durable, easy to install..
  • Plug and Play - Directly replace the old relay. Eliminate the need for tapping wires to install the load resistors..
  • Buy with Confidence - Package included: 1PC 2 Pin motorcycle LED flasher relay.
  • You are backed by 6-Month warranty since order purchase date.Please feel free to contact us if you have any questions..
Check Stock

Xentec H11 relay wiring harness for HID kit

  • 8-Light 8000w High Power HID Master 120v~240v Grow Light Relay Controller w/120 volt Trigger Cable for Hydroponics (8-Light).
  • The trigger cable can be plugged into a standard 24-hour timer or environmental controller.
  • Maximum Lighting Wattage: 8000watt (1000 watt per outlet).
  • Minimum relay operations: 100,000 at full load..
Check Stock

Nilight Wiring Harness Kit 14AWG Heavy Duty 12V On-Off Switch Power Relay Blade Fuse for Off Road LED Work Light Bar-ONE Lead,2 Years Warranty

  • Universal fitment: the wiring harness is compatible with all automobiles, boats and devices equipped with a 12V DC power source.
  • 12 feet harness: 12ft heavy-duty harness, 14-gauge stranded wire, up to 380W load capacity, the length from relay to switch is extendable.
  • Illuminated switch: 3 pin on/off rocker switch with Red Indicator light when truing on, easy to turn on or off, long service life.
  • Circuit protection: power relay for safety protection. Blade fuse acts as the first Line of defense against overcurrent and short circuit.
  • Package include: 1 x 12 feet wiring harness, 1 x instructions.
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

ARTGEAR Automotive Relays for Car Truck Motor Boat Car Starter - 12V DC 120 Amp Split Charge Relay Switch with 2 Pin Footprint + 2 Terminal

  • 【Continuous Relay】 You can use it as continuous relay, if the relay keeps working for 5 hours, it would be better to stop it and then use it again . It could pass continuous 50A~60A current.
  • 【Package Contains】 1 x Heavy Duty Split Charge 120A ON/OFF Relay.
  • 【Large Capacity】 Up to 120A coil capacity able to handle those high current applications with ease, Heavy duty make or break (on/off) relay.
  • 【Long service life】 Life Expectancy Electrical: 100,000 Operations (at 30 Operations/min) Life Expectancy Mechanical: 10,000,000 Operations, keep a high level in ongoing work.
  • 【Applicable】 High Power automotive relays provide standard contact form, and has the standard 4 pin layout, fit of starter kills, dome light supervision, trunk release, polarity change, power door lock/actuator control etc.
Check Stock