Reviews Fan Relay Board

Dual Electric Cooling Fan Wiring Install Kit 185 Degree On 165 Off Engine Fan Thermostat Temperature Switch 40/50 AMP Relay Kit

  • Ⓞ Works for: 2 x 8 inch Fans 2 x 10 Inch Fans 2 x 12 Inch Fans 2 x 14 Inch Fans Single 8 Inch Fan Single 10 Inch Fan Single 12 Inch Fan Single 14 Inch Fan Single 16 Inch Fan (Two 16 inch fans, need 2 Relay Kits).
  • Ⓞ This kit includes a waterproof relay, 3/8" （or1/2"）NPT thermostatic switch (185* on / 165* off), and fuse block. For single fan setups. Perfect for your muscle car, 4x4, or hot rod!.
  • Ⓞ Scorpion 12 volt Electric Fan Wiring Harness, Relay, Sending Unit & Circuit Breaker 12V.
  • Ⓞ These are perfect to use to turn your Electric Cooling Fan on & off.
  • Ⓞ The 40 Amp Relay Helps take the Load & Aids in Starting the Fan with less Amps Also includes an Overload Circuit Breaker.
Check Stock

5V ESP8266 Dual Channel WiFi Relay Module IOT Smart Home Phone APP Remote Switch with 100M Transmission Distance

  • ON-BOARD ESP-01 WIFI MODULE: The relay board is equipped with on-board ESP-01 WiFi module and high performance microprocessor STM8S103..
  • UART DEBUG INTERFACE: The relay has reserved UART debug interface and STM8 SWIM program download interface..
  • SMART CONFIG TECHNOLOGY: The module uses smart config technology to complete the account and password configuration on the APP ESP-01 WiFi module on the mobile phone, and configure the username and password memory functions..
  • ON-BOARD 5V RELAY: This relay module adopts On-board 5V,10A250V AC 10A30V DC relay, which can continuously pull 100,000 times with diode discharge protection and short response time..
  • WORKING STATUS INDICATOR: The module has board mode selection and real-time working status indicator..
Check Stock

Macurco TX-12-HS White Hydrogen Sulfide H2S (Line Voltage) Fixed Gas Detector Controller Transducer with White Housing

  • Output: fan relay, alarm relay and 4-20ma current loop.
  • Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
  • Mounts on a standard 4” x 4” electrical box.
  • 5 a spdt fan relay controls starters of exhaust fans.
Check Stock

LG EBR74164805 Genuine OEM Relay Control Board for LG Range/Stove/Ovens

  • This LG Relay Control Board is a genuine OEM (Original Equipment Manufacturer) part manufactured to exact specifications.
  • Replacement LG brand Range/Stove/Oven Relay Control Board operates relays to regulate the oven elements.
  • LG EBR74164805 Range/Stove/Oven Relay Control Board receives signals from the main oven control board.
  • High quality LG OEM EBR74164805 Range/Stove/Oven Relay Control Board is manufactured with premium materials for durability and exact fit, be sure to....
  • Life's Good when choosing Genuine LG OEM Factory parts for your LG appliances.
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

Dual Electric Cooling Fan Wire Harness Kit 185 On 165 Off Thermostat 50 AMP Relay NEW

  • COMES ON AT 185 degrees AND TURNS OFF AT 165 degrees ..
  • Works for: 2 x 8 inch Fans 2 x 10 Inch Fans 2 x 12 Inch Fans 2 x 14 Inch Fans Single 8 Inch Fan Single 10 Inch Fan Single 12 Inch Fan Single 14 Inch Fan Single 16 Inch Fan (Two 16 inch fans, need 2 Relay Kits).
  • Included in this Relay kit: 185 Degree Thermostat Switch 1 Relay Wire Harness 1 3/8″ NPT Thread-In Probe 2 Ring Terminals 2 Fan Pigtail Connectors Included 1 Fuse Holder 3/8″ to 1/2″ Adapter 30 & 40 amp Fuses,English instruction.
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

Painless Performance 30133 Weatherproof PCM Controlled Fan Relay Kit, Ground Activated

  • Inexpensive protection for an electric fan and a vehicle's wire harness.
  • Relay activation by grounding the relay coil can be provided by most Powertrain Control Modules.
  • Provides direct battery power, protects PCM from voltage spikes and prevents the fan from back feeding through the vehicle's wire harness.
  • Kit includes weatherproof: SPST 35-amp relay, 30-amp circuit breaker, relay base with 10' harness, crimp-on terminals and mounting hardware.
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock