Reviews F35front Axle Bearing

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

CyclingDeal WTB ST i25 Mountain Bike Bicycle Novatec Hub with Tires Wheelset 11 Speed Tubeless Ready 27.5' - Front: Quick Release, 15x100mm, 20x100mm; Rear:Quick Release, 12x142mm 4 in 1

  • Rims: WTB ST i25, Tubeless Compatible System, NOT Includes Tubeless Tape and Valves. Wheel Size: 27.5", ETRTO 25-584. Inner Width: 25 mm. Spokes: 32 Stainless Steel.
  • Break System: 6 bolt Disc. Material: Alloy. Axle size convertible to fit on your different bikes.
  • Front Hub: Novatec XD641SB, Quick release, 15x100mm or 20x100mm Thru Axle(Axle not included),2 Sealed bearing, 32H, Gauge 14, Disc 6 bolts. Rear Hub: Novatec D462SB-SL , Quick release or 12x142mm(Axle not included), 2 Sealed bearing, 5 Pawls, 32H, Gauge 14, Disc 6 bolts, 9 10 11 Speed compatible.
  • Tyre: Continental X-King MTB Tyre 27.5" x 2.2. Tyre Max PSI: 65. Inner Tube: CST FV48.
  • Weight: 4153g/set=9.15lbs. Package: Front and Rear Wheels with Tyres, Tubes, Hubs, Hub Spacer, Quick Release, Axle Size Conversion Kit. Warranty: 2 Year..
Check Stock

Detroit Axle - 5-Lug Front Wheel Hub Bearing Assemblies Replacement for Sebring Cirrus 200 Dodge Avenger - 2pc Set

  • Fits: Specific Models - Check Fitment Chart and Product Description for Accurate Information.
  • Kit Includes: (2) Front Wheel Hub Bearing Assembly.
  • Hub Specifications: Position: Front Left and Right| Lugs: 5 Bolt| ABS Type: Encoder| Flange Type: 4-Bolt Square.
  • Undergo impact, wear, and fatigue testing to help ensure quality and durability.
  • 10-Year Warranty. Detroit Axle Is A Leading Supplier Of Hub Bearing Assembly, Wheel Bearing, Assembly Model. The Part In This Kit Are Direct Compatible With Chrysler 200 Sebring Front Wheel Bearing, Dodge Avenger Hub Assembly And Front Wheel Bearing, Wheel Bearing Assembly.
Check Stock

Detroit Axle - 2WD Only 6-Lug Front Wheel Bearing Hub Assembly for - 2WD Only 2000-2006 Silverado 1500, Sierra 1500, Yukon No Denali or Z71 - Driver Passenger

  • Front Wheel Bearing Hub Assembly 6-lug 2-pc Set For 2WD/RWD Models Only! This Front End Service Kit Contains A Front Left Wheel Hub, Front Right Wheel Hub, And Front Wheel Bearings To Complete A Wheel Bearing Hub Assembly Front Kit. This Wheel Hub Kit Is Also Known As A Front Wheel Assembly, Wheel Hubs Assembly, Front Assembly, Front Hub Bearing Assembly, Left Front Hub Assembly, Wheelbearing And Hub Assembly, Wheel Hub Assemblies, Wheel Hub Front, And A Front Hub Bearing Assembly Pair..
  • Hub Specification: Lugs:6 | Flange Type: 3-Bolt Triangular | ABS Type: Sensor Wire.
  • Replacement Hub And Wheel Bearing Assembly For 2WD Chevrolet Silverado 1500 1999 2000 2001 2002 2003 2004 2005 2006 2007. Chevy Suburban 1500 2000 2001 2002 2003 2004 2005 2006. Chevrolet Tahoe 2000 2001 2002 2003 2004 2005 2006. The Parts In This Kit Are Direct Replacements For Chevy Silverado Wheel Bearing, Silverado Front Wheel Bearing, Silverado Wheel Hub, Tahoe Hub Assembly, Chevy Tahoe Wheel Bearing, Wheel Hub Assembly Silverado, Suburban Wheel Bearing, And A Chevy Tahoe Hub Assembly..
  • Replacement Wheel Hub And Bearing Assembly Front For 2WD Cadillac Escalade Esv Ext 2002 2003 2004 2005 2006. Gmc Savana 2500 2003 2004 2005. Gmc Sierra 1500 1999 2000 2001 2002 2003 2....
Check Stock

ABN Inner CV Axle Removal Tool - CV Axle Puller Slide Hammer Set with 5 lb Slide Hammer and CV Joint Puller Adapter

  • [Remove Front Wheel Drive Axles Easily] To replace or repair your CV axle joints easily, use the ABN FWD Axle Puller Slide Hammer Puller Set.
  • The CV joint puller adapter and large slide hammer bearing puller allow you to create added torque to loosen and remove stubborn axle shafts and water pumps.
  • [Fits Your Needs] Chrome-plated 23 x 5/8-inch hammer bar features a 5/8-inch x 18 threaded section to fit your adapters, while the slide hammer CV axle adapter has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
  • [Easy to Use] Attach the inner CV axle puller to your axle slide hammer then position the adapter around the shaft behind the inner boot.
  • Slide the 5 lb hammer weight back and forth to create torque to pull out the axle.
  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Slide hammer CV joint puller and attachment design focuses the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Hardened hammer shaft provides strength and d....
Check Stock

Pair Set 2 Front Timken Wheel Bearing Hub Kit for Ford F-250 F-350 SD 11-16 4WD

  • Replacement for 2005-2010 Ford F-250 Super Duty (SRW.
  • Dana 60 AXLE) - [2005-2010 Ford F-350 Super Duty (SRW.
  • Kit Includes: 2x Front Axle Assembly + 2x Front Wheel Hub & Bearing Assembly.
  • Built to strict quality control standards.
  • Undergo impact, wear, and fatigue testing to help ensure quality and durability.
Check Stock

ABN Front Wheel Drive Axle Pulley Attachment - CV Axle Removal Tool CV Joint Slide Hammer Adapter

  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Unlike pry bars or CV axle fork tools, the CV shaft slide hammer axle attachments focus the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Heat-treated CV puller adapter with black oxide finish ensures optimal strength and durability while resisting rust and corrosion.
  • Inner CV axle removal tool has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
Check Stock

For 10-22 Ford F250 17 Inch Silver Steel Rim - OE Direct Replacement - Road Ready Truck Wheel

  • Replacement for 1999-2004 Ford F-250 / Ford F-350 Super Duty (4x4.
  • Both (2) Brand New Front Driver & Passenger Side Axle w/U-Joint for 1999-2004 F-250/F-350 35 Spline Dana 60 Axle.
  • Both (2) Front Wheel Bearing And Hub Assembly Set "Coarse Threads" - 515020.
  • FITS DANA 60 4x4 Single Rear Wheel Models Only - Coarse Hub Threads and ABS.
Check Stock

56 Pieces Skateboard Truck Hardware Kit Includes 8 Pieces Spacers, 8 Pieces Axle Nuts and 40 Pieces Speed Rings for Skateboard and Longboard

  • Package quantity: package comes with 8 pieces skateboard spacers, 8 pieces axle nuts and 40 pieces speed rings, enough quantity to fit on a skateboard or longboard and improve bearing performance.
  • Speed spacer: our skateboard spacer allows you to rotate the axle nut downward all the time, thus reducing slop and increasing bearing life, durability and performance.
  • The +/ -0.02 mm precision tolerance ensures nicely fit and very fast bearing at a time.
  • Speed rings: our speed rings can increase speed and extend longer bearing life by reducing friction among the bearing, axle nut and hangar.
  • Axle nuts: our axle nuts will prevent your wheels from falling off, the more you change your wheels and bearings, the more the axle nuts wear out and lose its tightness.
  • These standard size axle nuts will keep you locked up and will fit most skateboard/ longboard trucks with 8 mm axles (in fact, each truck has a standard 8mm axle size).
  • These axle nuts have thread dimensions of 5/16 inch.
  • Wide application: this skateboard tool kit can be applied for most skateboard/ longboard trucks, they are strong and with proper installation, are resistant to stripping.
Check Stock

8MILELAKE Rear Axle Bearing Puller Extractor Installer Set Axle Bearing Removal Remover Tool Kit

  • [APPLICATION]: This rear axle bearing puller can help to pull out semi-floating rear axle bearings quickly and effectively..
  • [EASY TO USE]: The washer of the axle bearing puller can captures the bearing firmly to distribute the force to the whole bearing, can avoid damage of the bearings and case..
  • [DURABLE MATERIAL]: The rear axle bearing removal tool is constructed from heavy duty cast steel, which has good strength and durability, can provide long service life..
  • [SIZE]: The bearing puller remover set includes fittings for main bearing tube: Small: 1" to 1-7/8.
Check Stock