Reviews Encoder Multiplexer - BestBuyersPro.com

Analog Devices ADG509ATQ Analog Multiplexer

【16-channel Analog Multiplexer】- This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
【Used for】- It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
【Process Digital Signals】- Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
【Bidirectional Internal Switch】- The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent cross talk, please turn off the switch first and then on..
【Note】- Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected). Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering..

This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
Use the CD74HC4067 16-channel analog signal switch.
Analog signal input: C0-C15 16 channels..
IT can be used the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
Wide operating temperature range: -55C to 125C.

[Specification]- Type: EC11 Encoder with Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 5pcs x Rotary Encoder Code Switch Digital Potentiometer.

[Specification]- Type: EC11 Encoder without Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 2pcs x Rotary Encoder Code Switch Digital Potentiometer.

[Specification]- Type: EC11 Encoder with Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 2pcs x Rotary Encoder Code Switch Digital Potentiometer.

✔Product type: DC Gear motor with two-channel Hall effect encoder.
✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
✔Single Output 120 Pulses Per Revolution: Gear Reduction Ratio: 1/10, Each Loop Output Pulses: 12PPR 10*12=120PPR.
✔Wiring Diagram: Red - Motor power terminal (+).
✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..

[Specification]- Type: EC11 Encoder without Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 5pcs x Rotary Encoder Code Switch Digital Potentiometer.

✔Product type: DC Gear motor with two-channel Hall effect encoder.
✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
✔Single Output 540 Pulses Per Revolution: Gear Reduction Ratio: 1/45, Each Loop Output Pulses: 12PPR 45*12=540PPR.
✔Wiring Diagram: Red - Motor power terminal (+).
✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..

✔Product type: DC Gear motor with two-channel Hall effect encoder.
✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
✔Single Output 1176 Pulses Per Revolution: Gear Reduction Ratio: 1/98, Each Loop Output Pulses: 12PPR 98*12=1176PPR.
✔Wiring Diagram: Red - Motor power terminal (+).
✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..