Reviews Drv 882stepper Motor Driver 2

HiLetgo 5pcs DRV8825 Stepper Motor Driver Module for 3D Printer RepRap 4 RAMPS1.4 StepStick

★ Latest CNC Shield Expansion Board V3.0 ★-CNC shield board is updated version 3.0, which is suitable for CH340G Shield 3.0 version compatible....
★ Professional 3D printer CNC Kit ★ This is a professional 3d printer DIY kit with multiple types of modules or components you need. It is a great....
★ Premium Quality ★ Each part of this Logrunner 3d printer conk kit was made of premium material. These components can be used in a wide range of....
★ DRV8825 Stepper Motor Driver with Heat Sinks ★ High quality stepper motor drive with 4 Aluminum Cooler, running within 2.5A current (Maximum),....
★ Good after-sales service. We'll respond within 24 hours for any questions..

Can be applied for passive cooling of Stepper Motor Module TMC2130 TMC2100 A4988 DRV8825 TMC2208.
With thermal conductive adhesive tape backing.
Stepper motor driver module is not included.
Dimension: 0.35 x 0.35 x 0.47 inch / 9mm x 9mm x 12mm (L*W*H), Weight: 0.04 oz / 1 gr per piece.
Includes 22 pieces blue aluminum heatsink.

TMC2209 V3.0 Stepper Motor Driver is an ultra-quiet two-phase stepper motor drive chip.
It can compatible with StepStick and Pololu A4988.
It can replace the original TMC2208, A4988, DRV8825, LV8729 and so on.
5 pcs Drive capability up to 1.7A (RMS) continuous coil current - 2.8A Peak.
Step/Dir interface with microstep interpolation (up to 256 microsteps).

This controller board is designed for Genmitsu CNC Router 1810-PRO, 3018, and 3018-PRO. It can perfectly compatible with SainSmart Blue Laser Module..
Software: GRBL controller, UniversalGcodeSender..
Support XYZ three-axis control, spindle and laser module. Support 3 pin and 2 pin lasers (the 2 pin lasers: please connect the white interface " + s-")..
Support stepper motor: 12V, the maximum current within 2A, recommended within 1.5A and additional heat. (Any stepper motor 42, 57)..

♞【Product】3 Axis nema23 stepper motor driver usbcnc controller kit.
♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 425oz-in,280Ncm / Motor Size:57x57x112mm / Phase:2 / 4pcs lead wire / 1.8 Step.
♞【Stepper Motor Driver】FMD2740C Stepper Motor Driver / 4Amps / Support voltages:12 to 50V DC / 128microstep.
♞【4 Axis USBCNC breakout board】 Come with Hand Control with USB Cable / Only support USBCNC software / input voltage: 15-36V DC..
♞【DC Power Supply】400W 36V 11A DC Switching power supply.

Stepper motor with a standard interface..
A, B, C, D four-phase LED indicates the status of the stepper motor work..
Drive Module Board Size(in): 1.37*1.18*0.6.
5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board，With convenient use, direct docking.
Package Content: 5 set 28BYJ-48 Stepper Motor + Uln2003 Driver Board +20pcs female to male Dupont cable (as a gift).

Support a Variety of Stepper Drivers -- 2560 and Ramps 1.4 are integrated in the board, which avoids the problem of complicated connectors and malfunctioning. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100, available to change the stepper drivers and motors as users like..
Reserve External Driver Signal -- available to connect external high-current driver to drive the 57 and 86 stepper motors. Use high-quality MOSFET, better cooling effect and more stable. Use specific power chip, support 12V-24V power input, and resolve t..
Use CH340 Serial Port Chip -- Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing. Use CH340 serial port chip, more easily install the drive than 16U2..
Support 24V Input -- The heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats. Run Marlin firmware, the configuration is completely same as Ramps 1.4..
Compatible With -- Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32. X-axis, Y-axis and Z-axis with different color terminal controls the stepper motors and endstops, which is convenient to wire..

5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
Stepper motor with a standard interface could be connected with Driver Board easily.
A, B, C, D four-phase LED indicates the status of the stepper motor work..
5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.

3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
This shield can make quick work for managing stepper motors in your project..