Reviews Driver Board

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

  • 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface could be connected with Driver Board easily.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
  • Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.
Check Stock

VU Meter 2x Panel VU Meter Warm Back Light Recording & Audio Level Amp with Driver Board

  • L/GND/R: This driver board with low level signal input terminals for connections are CD players, computer sound cards, the first stage, and other audio signal source device, wiring L, GND, RW respectively: Left, the right channel.
  • Power Consumption:Input AC / DC 12V-15V power supply for the drive plate. (Recommended independent power transformer, or a separate power supply for the winding. the backlight current is 45 mA when drive plate off work.
  • 2 Resistor:R1 and R2 are two adjustable resistors of driver board,which can control the size of the hands swing..
  • Rectifier RegulatorThe backlight DC12V power meter is used for rectifier regulator of the backlight driver board Please notice that the positive and negative head interface..
  • Package Content:2 x VU Panel Meter+1 x Driver Module+1 x Cable.
Check Stock

Bebê a Bordo

  • ...ty for long-lasting usage. It must be remembered that folding not allows..
  • Vivid Colors & Highly Reflective: Bright colors and fonts make other cars keep their distance from your car to prevent rear-end collisions. Clear and high reflexes baby on board stickers for car in low light or during night time can catch the driver's attention and make the baby safe in the car..
  • Easy to Install & Clean: Baby on board sign for cars only take a few seconds to install. Guaranteed that baby on board sign will stay firmly in place and won't fall off from car, and there will be no other traces left when they are removed. They're easy to clean just with a clean damp cloth clean the back of the vehicle and on the back of the student driver magnet..
  • You Will Get: 2 pcs baby on board sticker for cars (yellow), 1 pcs baby on board magnet (orange), 4 pcs baby on board suction cup, our 7*24 friendly customer services for peace of mind..
Check Stock

ANNOYTOOLS GRBL 1.1f 32-Bit CNC Control Board for 3018/3018Pro CNC Milling Machine Laser Engraving Machine, Maximum Support 48V 500W Spindle, 3-Axis Control Board Integrated Driver Controller Card

  • ⚠️ If you're using a computer with Versions higher than win8, you not need to install the driver files from the USB drive when connecting your control board. Simply ensure that your computer is connected to the internet when you connect the board, and the driver should automatically load. Note: This only applies to Versions higher than win8. If you're using an earlier version of Windows, you'll still need to install the driver from the USB drive..
  • ⚠️To protect novice and non-professional users, this control board has built-in protection programs that prevent firmware modification. Please confirm whether the board's features meet your requirements before purchasing..
Check Stock

NC for LP140WF1 (SP)(B1)/(SP)(J1)/(SP)(K1)/(SP)(K3)/(SP)(U1) EDP 30PIN 1920x1080 Monitor LED HDMI-Compatible+VGA Controller Board (LP140WF1 (SP)(U1))

  • Controller Board Description: The controller driver board work for EDP Interface LCD Screen Come In Standby Mode When Not Input Signal Standby Mode.
  • The kit includes: 1Pcs x EDP controller driver board 1Pcs x EDP signal cable 1Pcs x Keyboard with cable.
  • Work compatible with the following LCD screen model: LP140WF1 (SP)(B1) LP140WF1 (SP)(J1) LP140WF1 (SP)(K1) LP140WF1 (SP)(K3) LP140WF1 (SP)(U1).
  • Great visuals: This LCD driver board provides excellent detail with a stunning resolution, making it perfect for productivity and multimedia applications..
  • Energy-friendly: This product design that emphasize recyclability, waste reduction, energy efficiency and safety..
Check Stock

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • Stepper motor with a standard interface..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Drive Module Board Size(in): 1.37*1.18*0.6.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board，With convenient use, direct docking.
  • Package Content: 5 set 28BYJ-48 Stepper Motor + Uln2003 Driver Board +20pcs female to male Dupont cable (as a gift).
Check Stock

AIR LIFT 25804 Air Shock Controller Kit

  • Allows driver control for air shock pressure right from the driver seat.
  • Universal connector for most air shocks including factory installed.
  • Includes dash mount gauge panel and hardware and air line.
  • Easy to installDescriptionAIR LIFT Air Shock Controller Kit is designed to control the air shock pressure. It includes rugged on board air compressor and dash mount gauge panel as well as hardware. This kit facilitates easy and quick installation..
Check Stock

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • ❃❃ The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable..
  • ❃❃ Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in).
  • ❃❃ A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • ❃❃ 5 line 4 phase can be used for ordinary ULN2003 chip driver, Connect to the 2 phase, Support the development board, With convenient use, direct docking..
  • ❃❃ Great packing in a box : 6 PCS ULN2003 Stepper Motor + Driver Board (with a little gift)..
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length：9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

Ili9341 LCD Display Module, ILI9341 5V/3.3V 2.8\ TFT SPI Serial Port LCD Touch Panel Display Module, 240x320[with Touch(9 IO Drive)](Without Touch)

  • With PCB board (including power supply IC, touch IC, SD card cage) compatible 5110 interface. At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch). 2.8 inch TFT LCD color screen, support 65K color display, and the display is colorful, high quality image display and wide viewing angle..
  • This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution..
  • On-board level translation programs truly perfectly compatible 5V / 3.3V IO level, supports a variety of single-chip IO connection, professional and practical..
  • We strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..
  • Buy it Confidence: Let you feel safe using, so you have a better using experience. Great value for money. If you have any problems, please fell free to contact us anytime. Our team w....
Check Stock