Reviews Differential Output

Taidacent AD8130 Differential Receiver Amplifier Module Differential to Single-ended High Common-mode Rejection Ratio Low Noise Low Distortion

  • Name: AD8130 Differential Amplifier Size: 43mm X 38mm Supply voltage range: ±5V~±12V.
  • The differential-to-single-ended amplifier, which has a 270-MHz bandwidth and a very high common-mode rejection ratio (CMRR) at high frequencies, can also be effectively used as a high-speed instrumentation amplifier or to convert a differential signal to a single-ended signal..
  • Differential amplifiers can process single-ended inputs as interactive differential outputs or treat differential inputs as differential outputs. These amplifiers have two independent feedback loops that control the differential and common-film output voltages, respectively..
  • Chip features 1. High speed AD8130: 270 MHz, 1090 V/us (G= +1) AD8129: 200 MHz, 1060 V/us (G= +10) 2. High Common Mode Rejection Ratio (CMRR) 94 dB (minimum, DCE100 kHz) 80 dB (minimum, 2 MHz) 70 dB (10 MHz) 3. High input impedance: 1 MQ differential 4. Low noise AD8130: 12.5 nV/Hz AD8129: 4.5 nV/vHz.
  • 5. Input common mode range: ±10.5V 6 low distortion, 1V peak-to-peak (5 MHz): AD8130, -79 dBc (Worst Harmonic, 5 MHz AD8129, -74 dBc (Worst Harmonic, 5 MHz) 7. User adjustable gain G= +1 without external components 8. Supply Voltage Range: +4.5V to ±12.6V 9. Power saving mode.
Check Stock

Taidacent AD8015 Wideband/Differential Output Transimpedance Amplifier Module Single-Ended to Differential 240M Bandwidth 155Mbps Data Rate

  • The AD8015 is a wide bandwidth, single supply transimpedance amplifier optimized for use in a fiber optic receiver circuit. It is a complete, single chip solution for converting photodiode current into a differential voltage output..
  • The 240 MHz bandwidth enables AD8015 application in FDDI receivers and SONET/SDH receivers with data rates up to 155 Mbps. This high bandwidth supports data rates beyond 300 Mbps. The differential outputs drive ECL directly, or can drive a comparator/ fiber optic post amplifier..
  • In addition to fiber optic applications, this low cost, silicon alternative to GaAs-based transimpedance amplifiers is ideal for systems requiring a wide dynamic range preamplifier or singleended to differential conversion..
  • Application: Fiber Receiver: SONET/SDH, FDDI, Fibre Channel Stable High Capacitance Detector.
Check Stock

DAOKI 5PCS PAM8302 2.5W Single Channel Class D Audio Power Amplifier Module Amp Development Board for DIY with Dupont Cable

  • This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers, Inside the miniature chip....
  • Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable....
  • The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply....
  • The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency....
  • Package Content:5 x PAM8302 Class D Amplifier Module, 1 x 11.8" Female-Male Dupont Cables 30 PIN.
Check Stock

Handwheel Off-Line Controller, DDCSV3.1 4 Axle Off-Line Controller with Emergency Stop Function Handwheel Kit for CNC Control

  • 16 opto isolated digital inputs,3 opto isolated digital outputs. ARM9 main control chip,FPGA core algorithm chip..
  • Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version..
  • 4 axle motor Control.Differential Pulse and direction output signal,maximum.500Khz per axle..
  • Handwheel Three Output:Voltage, Single-Ended, Differential.
  • USB flash disk support for G code file input,no size limited of the G-code file..
Check Stock

EMB Professional EBX9Series Sound System Digital Crossover with XLR Input and Output for Home, DJ Performance, Club, Studio, Stage, Show, Entertainment

  • Stereo half-frequency, single-channel third-frequency electronic crossover. Trs or XLR balanced input and output Differential. Choice of stereo or the sum of left and right channels while the synthesis of ultra-low sound. Two channels are selected Xiao range switch. Two channels have 40Hz high pass filter (frequency cut End). all outputs with phase reverse switch.
  • Technical parameters: TRS or XLR balanced input and output Differential/ choice of stereo or the sum of the synthesis of left and right channel subwoofer.
  • The scope of the two-channel selection switches are x 10 two channels have 40Hz high pass filter (frequency cut End).
  • Therefore, the output spectrum can be independently adjusted average dB/ Oct linkwttz-riley filters (the professional standard). stereo/ mono status indication Leo lights, indicate the selected Mode of operation.
  • 24dB/Oct linkwitz-riiey filters (the professional standard) stereo/ mono status indication Leo lights, indicate the selected Mode of operation.
Check Stock

HIFIMAN EF400 Desktop Balanced Headphone DAC& Amplifier with Himalaya R2R DAC, 3.5/4.4/6.35mm Output for Home Audio

  • ...f-band noise, and low energy consumption make it a perfect match for high-performance audio equipment. The HIMALAYA DAC module supports the standard PCM music signal transmitted by the most common IIS (Integrated Interface of Sound) audio interface, with a maximum resolution of 24Bit..
  • Full Balance: The four-channel differential structure features a DAC, buffer and active filter that add up to unbeatable fully balanced output for stunning performance from a Class AB DAC/amplifier. The four-channel fully differential amplifier circuit features a maximum output of 10.7 Vrms (THD.
  • 4-level Function Switch: High Gain NOS, High Gain OS, Low Gain OS, Low Gain NOS ★Headphone Out (Front Panel): 6.35mm Single-ended.
  • XLR 4-Pin Balanced Output. ★Line Out (Rear Panel): CANNON Balanced Output.
  • RCA (Single-ended).★ Input: USB Type C.
Check Stock

Micsig 700V 100MHz High Voltage Differential Probe kit 3.5ns Rise Time 10X/100X Attenuation Rate Oscilloscope Probe Kit Accessory DP10007

  • Widely Used: The attenuation rate is 10X/100X, widely used in any brand of oscilloscope..
  • Maximum differential test voltage (DC+ACPK-PK): 70V (10X), 700V (100X). You can safely measure floating voltages up to 700V and have a bandwidth up to 100 MHz..
  • Easier and Safer Use: High voltage differential probes sample high impedance isolation between input and output to protect person safety. Power supply USB DC 5V output, more portable while Oscilloscope has USB interface..
  • Versatile Kit: All 6 pieces with three different connectors help to test various on different occasions, including 2 alligator clips, 2 hook clips and 2 pincer clips..
  • Applications: Floating Measurements, Switch-Mode Power Supply (SMPS), Motor Drive Design, Power Device Testing & Evaluation, Power Converter Testing & Design..
Check Stock

Micsig DP10007 High Voltage Differential Probe Kit, Oscilloscope Probe Kit, 100MHZ 700V

  • 【Maximum differential test voltage】 Comes with 70V-700V measurement range, you can safely measure up to 700V floating voltage and up to 100 MHz bandwidth..
  • 【High voltage conversion】The testing probe kit can convert the input high voltage signal to low voltage signal for oscilloscope observation and analysis..
  • 【Safer to use】High-impedance isolation between the sampling input and output of the high-voltage differential probe to protect personal safety..
  • 【Multifunctional kit】All 6 pieces come with three different connectors, which are helpful for various tests on different occasions..
  • 【Wide application】The attenuation rate is 10X/100X, which is widely used in most of oscilloscope..
Check Stock

Micsig DP10013 High Voltage Differential Probe 1300V 100MHz 3.5ns Rise Time 50X/500X Attenuation, Tektronix P5200A P5205A P5210A

  • Lightweight and portable, easy to carry..
  • Designed for the measurement of high voltage differential signal, to meet the demand for floating measurement..
  • Power supply USB DC 5V output, more portable while Oscilloscope has USB interface..
  • Simple design, it is easy and safe to use..
  • Maximum differential test voltage (DC+ACPK-PK): 130V (50X), 1300V (500X).
Check Stock

TSL1401CL Linear Sensor 128X1 Linear CCD Camera Sensor Ultra Wide Angle Lens 120 Degree Black and White Line Tracking Module

  • BASIC SPECIFICATIONS: With sensitivity pure tones , field cut and signal output, circuit board output switch (can be directly passed through the microcontroller).
  • MULTIPLE OUTPUTS: The linear magnetic sensor switches has signal output indication, single signal output, active low signal output.
  • IDEAL CHOICE: This linear magnetic sensor switches is ideal for temperature control, proximity switches, alarm detection or rotate encoders.
  • WITH SENSITIVITY: Universal sensor module with potentiometer to adjust the sensitivity of the sensor, provides analog and digital output.
  • HIGH COMPATIBILITY: With A3141 chipset, 49E linear effect sensor, LM393 dual differential comparator, potentiometer, 2 LED and 6 resistors, fully compatible with standard microcontrollers.
Check Stock