Reviews Cylinder End Cap

DONSP1986 PK80 Motor Replaement of Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc

  • PK80 Replaement of Top End Cylinder Set and Bottom End Crank Set for 2 stroke kit 66cc/80cc.
  • better adjusting Clutch a little before riding.
  • PK80 Replaement of Top End Cylinder Set and Bottom End Crank Set with AF80 connecting rod.
  • High hole Piston and Long connecting rod.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Check Stock

CDHPOWER Super Motor PK80 Replaement with Iron Sleeve Cylinder 49mm Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc

  • CDHPOWER Super pk80 motor Replaement:Iron Sleeve Cylinder 49mm:Top End Cylinder Set and Bottom End Crank Set for 2 stroke kit 66cc/80cc pk80 motor kit.
  • High hole Piston kit installed well inside of cylinder and Long connecting rod AF80 or zmn80.
  • The casting cylinder head increases the horse power and this greatly cools off the engine. Would result better performance and longer life for your 2 Stroke Bicycle Engine. Casting cylinder head Height Max:51mm-52mm.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Check Stock

Self Locking Gate Gravity Latch Stainless Steel Spring Loaded with Adjustable Gate Latch Cable Pull for Metal Wooden Fences 2 Pack (Red 2 Pack)

  • Stainless steel cable with red power coated and PVC coating finish with weatherguard technology to protect against rust and weather..
  • Fits gates with a 4 inch to 2-6 inch thickness. The brass cylinder is just fits the hole that greater than 0.18 inches (4.5mm) and less than 0.31 inches (8mm) for the brass cylinder nut to fit in the hole..
  • Stainless steel spring assisted pull for one hand operation, gate latches can still be padlocked while using this gate pull..
  • Use this cable pull with new or existing gate latches.
  • This cable pull does not come with a gate latch..
  • For use with metal, vinyl, and wood gates. Contents: Package includes Gate latch cable *2+ brass cylinder *2+ spring*2+End Cap*2+Hexagonal Wrench*2..
Check Stock

Westbrass D3322-1 Tip Toe Bathtub Drain Plunger Polished Nickel

  • 3/8 Thread at End of Adjustable cylinder..
  • Please Note: Color not as pictured, but as noted in name..
Check Stock

Zeda 100 Complete 80cc/100cc Bicycle Engine Kit - Firestorm Edition 44 Tooth

  • Firestorm Zeda100 3+ HP bicycle engines with high performance heads & CDI Yamaha components.
  • 50mm Bore/40mm Stroke/US displacement 78.6cc/40mm Intake & Round Exhaust/Type B piston 89mm Long rod.
  • Increased weight capacity, Low operating temps, Easy starting, Sustained power output across rpms.
  • Pearl anti-corrosion coat w/ Z8C spark plugs & 60% Thicker crank case for bearings.
  • Improved magneto/50mm bBore single piece cylinder/High-end Allen bolts & Improved gas cap.
Check Stock

Cavagna (52-A-890-0006C Auto Changeover Regulator Kit

  • Cavagna AUTOMATIC CHANGEOVER REGULATOR - Kit Includes Mounting Bracket And Plastic Cap Cover Automatically switches from empty service cylinder to full reserve cylinder, ensuring continuous gas flow to appliances.
  • Highly visible full/empty indicator signals need for refill.
  • Built-in back check valve allows empty cylinder removal and refill as reserve cylinder remains operational.
Check Stock

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

  • Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
  • Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
  • Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
  • Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
  • Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
  • Material:The handle of ignition coil puller is made of hard p....
Check Stock

CDHPOWER PK80 Motor Replacement of Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc

  • PK80 MOTOR REPLACEMENT PARTS ONLY. piston kit is installed well inside of cylinder already.
  • better adjusting Clutch a little before riding.
  • High hole Piston and Long connecting rod.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Check Stock

MOOSUN Cylinder Piston Gasket Top End Kit Fits 1988-2006 Yamaha Blaster 200 YFS200

  • 【BLASTER 200 CYLINDER TOP END KIT】Compatible with 1988-2006 Yamaha Blaster 200 YFS 200.
  • 【SPECIAL FUNCTION】MOOSUN Blaster 200 Cylinder replacement piston sets engineered from premium materials to provide exceptional service life and....
  • 【BLASTER 200 CYLINDER HEAD PISTON FEATURE】Cylinder piston set is the heart of engine. MOOSUN Cylinder has been factory honed and deburred to help....
  • 【PART NUMBER】2XJ-11111-00-00, 2XJ-11311-02-00,2XJ-11181-00-00, 2XJ-11631-01-97, 3JM-11351-02-00, 3JM-13621-00-00, B8E-S0000-00-00,....
  • 【CYLINDER PISTON RING GASKET KIT COMES WITH】1 x Cylinder, 1 x Piston, 1 x Piston Rings, 1 x Wristpin, 2 x Circlips, 1 x Needle Bearing, 1 x Head....
Check Stock

Distributor Cap Rotor and Spark Plug Wires Set - Ignition Tune-Up Kit - Compatible with 1984-1996 Ford F-150 4.9L 6-Cylinder

  • Compatible with or fits: (Note: Tall Cap) 1984 - 1986, 1996 Ford F-150 4.9L 6-Cylinder.
  • Compatible with or fits: 1995 Ford F-150 Special 4.9L 6-Cylinder.
  • Compatible with or fits: 1995 Ford F-150 Eddie Bauer 4.9L 6-Cylinder.
  • Compatible with or fits: 1993 - 1995 Ford F-150 XL 4.9L 6-Cylinder.
  • Compatible with or fits: 1993 - 1995 Ford F-150 XLT 4.9L 6-Cylinder | 1987 - 1992, 1996 Ford F-150 4.9L 6-Cylinder.
Check Stock