Reviews Compression Ring Puller Tools

Fiada 2 Pcs Olive Puller Olive Remover Puller Tool Compression Sleeve Puller Ferrule Removal Tool for 1/2 inch and 3/4 inch Brass Pipes

  • Applicable Model: the ferrule removal tool can be applied for brass pipes or copper pipes with diameter of about 15 mm/ 1/2 inch and 22 mm/ 3/4 inch,....
  • No Damage to the Pipe: the compression ring removal tool is an ideal tool for you to remove olives from pipes, allowing you to remove damaged olives....
  • Sturdy for Long Time Use: made of solid brass material, the compression sleeve puller is smooth on the surface, with high strength and hardness, not....
  • Simple to Apply: the ferrule puller is easy to use, no need to read the manual or use other tools to work, saving your time and energy, convenient for....
  • Wide Range of Applications: the olive puller for compression sleeve has a wide range of applications, to increase torque and remove olives more....
Check Stock

Compatible with Compression Sleeve Puller（03943）-- Sleeve Remover for 1/2-Inch Compression Fittings Only -- Corroded & Frozen Supply Stops --Plumbing Tools Compression Ring Removal Tool

  • Make Your Life Easy--This sleeve remover removes 1/2-inch copper water compression sleeve.This compression sleeve puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe..
  • Saves A Lot Of Time-- if you don't have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. Saves a lot of time around cutting old pipes..
  • Resistant & Wear Resistant.--Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe.Ideal for working on frozen or corroded supply stops,corrosion resistant & wear resistant..
  • Operating Steps--1.Remove the old compression fitting or the old angle stop. 2.Put the nut of pipe to the golden threaded mouth of the puller tool to tighten the screw 3.Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. 4.T....
Check Stock

VKALTUL Pipe Olive Remover Puller Tool Easy Removal Without Damage, Olive Puller Ferrule Puller, Compression Sleeve Puller Suitable for Brass Olive Pipes with Diameters of 1/2in & 3/4in

  • 【No Damage】VKALTUL pipe olive remover puller tool is used to remove used or damaged olives from the air-conditioning pipes without damaging the pipe by uillizing compression fittings to lock nut. It can increase torque and remove olives more easily..
  • 【Two in One】The olive puller is combined with one double hex and one single hex wheel socket. The double hexagonal one is suitable for 1 / 2 inch diameter brass pipe, and the single hexagonal one is suitable for 3 / 4 inch diameter copper pipe. Two in one design is easy to carry and store, and does not occupy space..
  • 【Premium Material】This compression ring removal tool is made of solid brass with high strength, high hardness, corrosion resistance, wear resistance, high finish, which have long service life..
  • 【Easy to Use】Ferrule blaster ferrule puller is easy to operate, and you can work without reading the manual or using other tools, reducing the working time and improving the working efficiency..
  • 【Save Effort】The zinc-plated Tommy bar at the head of ferrule puller is designed by the lever principle, and can move left and right according to the demand to achieve the effect of labor saving..
Check Stock

VEVOR Carrier & Pinion Bearing Puller Compatible with Dana 30,40,50,60,70, 80, Ford 10.25  Bearings Pinion Puller Tool with 3 Clamshells 45# Steel Clamshell Bearing Puller for Auto Repair

  • Great Compatibility: The clamshell carrier bearing puller is compatible with Dana 30, 40, 60, 70, Ford 10.25" bearings. With the clamshell bearing puller, you can quickly remove the bearings. In addition, its power is evenly distributed, so less damage will be brought to your pinion bearings..
  • Premium Performance & Features: With high working efficiency, this carrier pinion bearing puller can effortlessly remove the pinion bearings with minor damage, drastically reducing dismantled time. And the carrier bearing puller will no longer easily pry into the pinion's sealing surface..
  • Complete Equipment: All necessary parts are ready for you. There is a main puller body, plug, center bolt, 3 clamshells, retaining ring, and adjuster rings. Besides, this unit comes with a handy stand, so you can group all the working parts together..
  • Easy to Operate: There is no need for other complex working tools. Firstly, place the main body over the plug and adjust the lower and upper adjusting ring. Secondly, select a proper clamshell and tighten the retaining ring. Finally, you can use an impact gun to remove the bearing..
  • Superior Material: The clamshell bearing tool is made of durable 45# steel, providing good performance in withstanding abrasion, corrosion, and impa....
Check Stock

Prokomon 13 Pcs Embedded Bearing Puller Kit for 6004-6010 6201-6206 6300-6302 Insert Wheel Bearing Removal Tool with 6 Pcs Ball Ended Threaded Puller Adaptors

  • ◇ Embedded Bearing Puller --- The bearing puller is used to dismantle automotive bearings. When a normal puller cannot remove the bearing, using this tool can help you complete the removal task..
  • ◇ Applicable ISO Bearing Sizes ---The wheel bearing removal tool is suitable for ISO bearings of sizes 6004-6010,6201-6206 and 6300-6302..
  • ◇ High Quality Materials --- Bearing puller tools are made of hardened and tempered steel, chemically plated black for excellent corrosion resistance and improved service life, providing you with long service..
  • ◇ Easy To Use --- First choose the right slider, put the slider into the bearing housing ring, rotate it 90 degrees, install the right post, then install the crossbeam and the top screw, turn the screw clockwise and pull out the bearing..
  • ◇ 13 Pcs Set--- Bearing removal tool pack contains centre screw thread cap,6 x ball ended threaded puller adaptors,2xleg extensions,and puller yoke with centre screw and twin arms..
Check Stock

Olive Puller Not Damage The Pipe Olive Remover Ferrule Puller Corrosion-Resistant Copper Pipe Fittings Suitable for Brass Pipes with Diameters of NPT 1/2 Inch & NPT 3/4 Inches Ferrule Removal Tool

  • ... attached. In fact, the pullers shipped by Amazon do indeed work on brass pipes with diameters of NPT 1/2 Inch & NPT 3/4 Inches.Please refer to the actual use..
  • 【Olive Puller That Will Not Damage The Pipe】This DUOYI olive puller is an ideal tool for taking out olives.Without damaging the pipe,puller utilises the compression fitting locking nut to remove the olives which used or damaged from the copper piping..
  • 【Suitable For Brass Pipes With Diameters Of NPT 1/2 Inch & NPT 3/4 Inches】The olive puller can work on air-conditioning pipes,and is suitable for brass pipes with diameters of NPT 1/2 Inch & NPT 3/4 Inches..
  • 【Abrasion-Resistant & Corrosion-Resistant Solid Brass】The DUOYI ferrule puller is made of high-quality solid brass,which not only has high strength and high hardness,but also has good wear and corrosion resistance. In addition,the olive puller has a smooth surface High,with high-grade texture,and long service life,can provide you with long-term service..
  • 【Easy To Use】Olive puller is easy to operate,and you can work without reading the manual or with the help of other tools,reducing work time and energy..
Check Stock

Compression Sleeve Puller (4661) - Remove Nut & Ferrule Of Pipe - Ferrule Puller For 1/2” Copper Water Compression Sleeve - 1/2-Inch Copper Tubing - Plumbing Tools Compression Ring Removal Tool

  • Saves A Lot Of Time--This ferrule puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. Saves a lot of time around cutting old pipes..
  • Make Your Life Easy--This compression sleeve puller removes 1/2-inch copper water compression sleeve. No damage to the copper. Makes removing a ferrule simple, and makes plumbing work simple..
  • Operating Steps--Method 1: Only remove the ferrule---Let the ferrule in between the red notched end of the tool (notched clamping ferrule). Method 2: Both remove the compression nut and ferrule---Place red notched end of tool behind compression nut. Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle..
  • Resistant & Wear Resistant.--Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe.Easy and fast solve the problem of compression valves failing with small leaks.Ideal for working on frozen or corroded supply stops,corrosion resistant &....
Check Stock

JEUCLEL US Standard Olive Remover Puller Tool for 1/2-inch / 3/4-inch Dia Solid Brass Pipe Fitting, Olive Removal Tool for Copper Pipe, Compression Sleeve Puller

  • 【Ideal Tool】 This olive puller is the ideal tool for removing olives from pipes. It utilizes a compression fitting to lock the nut, thereby removing damaged or used olives from the pipe without damaging the pipe..
  • 【Applicable Specifications】 The olive puller can be applied to brass or copper pipes with diameters of 1/2 inches and 3/4 inches..
  • 【Premium Material】 The olive puller is made of solid brass. It has the advantages of high strength and high hardness. It has strong wear resistance and corrosion resistance, and has a long service life..
  • 【Easy to Use】 This olive removal tool is very simple to operate, no need to read complicated instructions, it can be used easily. Save a lot of time and effort..
  • 【Wide Applications】 Olive removal tools are capable of various tasks. It is applied to the work of dismantling olives in various scenarios. It is an indispensable cost-effective tool..
Check Stock

Hachiko: The True Story of a Loyal Dog

  • LIGHTWEIGHT: 40% lighter than PVC and is spiral reinforced for increased durability.
  • STRENGTH: Handles 300 PSI with a 3-to-1 burst ratio.
  • DURABILITY: Bend restrictors add durability and stays flexible even in cold weather.
  • COMPRESSION RING: Has a crimped-on compression ring and comes equipped with a 6-ball brass fitting.
  • METABO HPT: Same tools. New name. Hitachi power tools has renamed to Metabo HPT.
Check Stock

ROADGIVE 97PCS Auto Body Dent Repair Tool Kit, Paintless Dent Repair Kit with Golden Lifter, Slide Hammer T-bar Dent Puller, Bridge Puller, Suction Cup and Glue Gun for Car Dent Remove Tools Kit

  • 【Premium Dent Removal Kit】The material of car dent puller is made of high quality alloy+plastic.They won’t break when taking a normal range of pressure. Each paintless dent repair kit is made of a special hardened material, is robust and durable and has a lifespan of several years..
  • 【Efficent Dent Repair】All dents are easily removed with our innovative auto body repair tools ! It contains all the tools needed to repair dents of all sizes and shapes.T-Bar puller for large dents, bridge puller for medium dents and gold dent puller for small dents..
  • 【EASY OPERATION】Our car dent repair tools are very easy to understand and manipulate, helping you save a lot of money compared with the auto repair shops. Our pullers pass mechanics test and they are easy to handle..
  • 【PHYSICS DESIGN】Using the principle of leverage to design the dent puller is ergonomic, the bridge dent puller with a unique arched bridge can adjust the spacing and rotate the button to better fit the dents, efficiently and labor-saving..
  • 【Dent Puller Kit】1xBridge Dent Puller(with 8xaccessory), 1xT-Bar P....
Check Stock