Reviews Compression Pipe

Compression Sleeve Puller Tool Remove Ferrule & Nut Of Pipe, Ferrule Puller For 1/2” Copper Water Compression Sleeve & 1/2-Inch Copper Tubing, Plumbing Tools Compression Ring Removal Tool

  • 【No Damage To Walls & Copper & Supply Lines】This ferrule puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. This compression sleeve puller removes 1/2-inch copper water compression sleeve. If you are in need of replacing a quarter turn valve on a dishwasher, sink or toilet that has compression fittings, buy this tool and make your life easy. Designed by plumbing professionals. Precision machined plumbing tool..
  • 【Not Need To Cut Off The Pipe】Saves a lot of time around cutting old pipes. Re-designed bullet nose will not pull off and is easy to use in relatively tight spots. Especially if you don’t have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. No damage to the copper. Makes removing a ferrule simple, and makes plumbing work simple..
  • 【Work On Corroded & Frozen】Even such as the existing valve was severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe. Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut....
Check Stock

Compression Sleeve Puller (4661) - Remove Nut & Ferrule Of Pipe - Ferrule Puller For 1/2” Copper Water Compression Sleeve - 1/2-Inch Copper Tubing - Plumbing Tools Compression Ring Removal Tool

  • Saves A Lot Of Time--This ferrule puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. Saves a lot of time around cutting old pipes..
  • Make Your Life Easy--This compression sleeve puller removes 1/2-inch copper water compression sleeve. No damage to the copper. Makes removing a ferrule simple, and makes plumbing work simple..
  • Operating Steps--Method 1: Only remove the ferrule---Let the ferrule in between the red notched end of the tool (notched clamping ferrule). Method 2: Both remove the compression nut and ferrule---Place red notched end of tool behind compression nut. Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle..
  • Resistant & Wear Resistant.--Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe.Easy and fast solve the problem of compression valves failing with small leaks.Ideal for working on frozen or corroded supply stops,corrosion resistant &....
Check Stock

Beduan Brass Compression Fitting, Insert Tube Support Compression Sleeve Fitting 1/4\ Tube ID (Pack of 10)

  • ✅[QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube ....
Check Stock

Hilitchi 8Sizes Tube OD 4mm-16mm Brass Compression Sleeves Ferrules Compression Fitting Kit Metric 220Pcs

  • ✅ [QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅ [FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon t....
Check Stock

Hilitchi 3Sizes Tube OD 1/4 5/16 3/8 Brass Compression Sleeves Ferrules Compression Fitting Kit (SAE, 105Pcs)

  • ✅[QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube ....
Check Stock

Pipe Olive Remover Puller Tool, CATUDIY Olive Puller for Compression Sleeve Suitable for Brass Pipes Plumbing Tools with Diameters of 1/2 Inch & 3/4 Inches Ferrule (US Standard)

  • 【Applicable Model】The compression sleeve puller not damage is suitable for brass pipes with diameters of 1/2 Inch and 3/4 Inch..
  • 【Powerful Design】The ferrule puller tool is able to remove used or damaged olives from the copper pipe without damaging the pipe by utilizing compression fittings to lock the inches nut, olive puller can work on air-conditioning pipes.
  • 【Ideal Removal Tools】The compression ring removal tool can increase torque, which is suitable for various tasks -- A handy duck puller tool to remove neatly used or damaged olives.
  • 【Superior Material】This Olive puller for copper pipes fittings puller are made of solid brass with high strength, high hardness, corrosion resistance, wear resistance, high finish, which have long service life.
  • 【Easy Using】The pipe tool can be used easily without checking any manual. Simple operation reduces frustration, saving more time and energy.
Check Stock

MILMUMU Compatible with Compression Sleeve Puller（03943） and Sleeve Remover for 1/2-Inch Compression Fittings Only

  • Compression Sleeve Puller and Sleeve Remover for 1/2-Inch Compression Fittings Only.
  • Ideal for working on frozen or corroded supply stops.
  • Easily removes compression sleeves Won’t damage walls.
  • Wt: 11 ounces Dimensions: 6.8 x 4 x 0.8 inches.
  • Function: Removes Compression Sleeves without Damaging Pipe. Screws Directly into Compression Nut for Removal.
Check Stock

Oatey 42239 Brass and Plastic No-Calk Shower Drain Wrench, Stainless Steel

  • Compression gasket tightens around 2″ Sch. 40 DWV pipe with caulking nut and wrench.
  • Can be used with 15″ Sch. 40 DWV pipe and 15″ or 2″ Copper DWV pipe when caulking gasket is replaced.
  • Available with 425″ Stainless Steel or UltraShine PVD Polished Brass Snap-Tite Strainer.
Check Stock

Parker Hannifin 62NTA-10 Brass Air Brake-NTA Union Fitting, 5/8\ Compression Tube x 5/8\ Compression Tube

  • Lead free approved product in all states.
  • 7/8-Inch compression by 7/8-Inch compression.
Check Stock

VKALTUL Pipe Olive Remover Puller Tool Easy Removal Without Damage, Olive Puller Ferrule Puller, Compression Sleeve Puller Suitable for Brass Olive Pipes with Diameters of 1/2in & 3/4in

  • 【No Damage】VKALTUL pipe olive remover puller tool is used to remove used or damaged olives from the air-conditioning pipes without damaging the pipe by uillizing compression fittings to lock nut. It can increase torque and remove olives more easily..
  • 【Two in One】The olive puller is combined with one double hex and one single hex wheel socket. The double hexagonal one is suitable for 1 / 2 inch diameter brass pipe, and the single hexagonal one is suitable for 3 / 4 inch diameter copper pipe. Two in one design is easy to carry and store, and does not occupy space..
  • 【Premium Material】This compression ring removal tool is made of solid brass with high strength, high hardness, corrosion resistance, wear resistance, high finish, which have long service life..
  • 【Easy to Use】Ferrule blaster ferrule puller is easy to operate, and you can work without reading the manual or using other tools, reducing the working time and improving the working efficiency..
  • 【Save Effort】The zinc-plated Tommy bar at the head of ferrule puller is designed by the lever principle, and can move left and right according to the demand to achieve the effect of labor saving..
Check Stock