Reviews Circular Locknut

OTC 1909 3-1/4" 8-Point Octagon Locknut Wrench

  • 3-1/4 inch 8-point octagon locknut wrench.
  • High strength steel resists rounding out.
  • For use with 3/4 inch square-drive manual tools only.
  • Measure from flat to flat to determine size of locknut.
Check Stock

KiWAV Tappet Valve Adjustment Wrench Tool Set Timing Chrome Vanadium Steel

  • The hand tool allows micro adjustment without disturbing the locknut which can be tightened when the correct clearance is achieved..
  • Use a 12mm wrench to hold the locknut socket while using square type driver to loosen or tighten the valve adjustment screw..
  • 8, 9mm locknut sockets and 3mm square type driver included..
  • Fits most motorcycles and ATVs with screw-type tappet adjustments..
Check Stock

NOVINO 14-1/2Dia X 19Pitch Boat Outboard Propeller for Mercruiser Alpha One Prop/Mercury Engine 135 150 175 200 220 225 250 300HP,3-Blade Aluminum 14.5dia x 19 Pitch Propeller,Replace OEM#48-832830A45

  • ... pitch Mercury/Mercruiser propeller,lower fuel consumption and great speed acceleration or rmps,,reduce the wear and tear on engine.
  • Easy Install: The propeller with hub kit Includes Flo-Torque hub kit (hub, splined hub, thrust washer, prop nut and keeper),Just remove prop locknut&locknut retainer& forward thrust washer.Then Install forward thrust washer---Insert drive sleeve into prop---Slide prop on prop shaft---Insert drive sleeve adapter--Slide locknut retainer---Install prop locknut---Insert sth to prevent spinning--Tighten prop locknut.
  • Fitment:perfect propeller replacement for 14.5x19pitch Mercury Engines 135 150 175 200 220 225 250 300HP&Mercruiser Alpha One Bravo One,detail information pls see below.
Check Stock

Sigma Electric ProConnex C-560 Snap Lock AC/MC Connector 3/8-Inch, 25-Pack

  • Terminates AC or MC to a 1/2" knockout without a locknut.
  • For aluminum or steel 14/2 - 10/3 AC or MC.
  • No locknut assembly for faster installation.
Check Stock

Gardner Bender LNW-3PC LNW locknut wrench, Assorted

  • Locknut wrench solves the problem of tight spaces and fits the majority of UL locknuts.
  • Etched markings allow for easy identification.
  • clearly marked tighten and loosen ends make usage a breeze.
  • each tool is a different color for easy size identification.
  • Thin design allows easy maneuvering in tight locations.
  • Hooked tip latches onto locknut and maximizes turning leverage.
  • 3-piece kit includes the 1/2 in. , 3/4 in. and 1 in. sizes.
Check Stock

Morris 21816 Liquid Tight Connector Straight Non-Metallic 1-1/4 Thread Size 1-Pack

  • Non-Metallic Liquid Tight Wire Connectors Straight With Steel Locknut - Our Liquid Tight Straight Connectors are weather and corrosion-proof..
  • For use with Non-Metallica Liquid Tight conduit.
  • Type B - Nylon construction with Zinc Die Cast Locknut - resists saltwater, gasoline, alcohol, oil and grease.
Check Stock

Whittet-Higgins CNM-08 Threaded Clampnut/Shaft & Bearing Locknut Collar, Metric M40 x 1.5 Right-Hand Thread, Self-Locking,

  • Slit locknut design with socket head cap screw provides single-point tangential locking.
  • Self-Locking. Prevents assemblies from loosening from large forces of vibration, shock and torque.
  • Easier and faster to install than traditional locknut & lockwasher.
  • Black oxide coating with wax finish to inhibit corrosion.
Check Stock

Gardner Bender LNW-KIT Locknut Wrench Kit, ½ & ¾ Inch., Loosen / Tighten locknuts, Steel Construction fits UL locknuts, 2 Pk. Bundle, Black

  • Locknut wrench solves the problem of tight spaces and fits the majority of UL locknuts.
  • Etched markings allow for easy identification.
  • clearly marked tighten and loosen ends make usage a breeze.
  • Thin design allows easy maneuvering in tight locations while durable steel construction makes it strong enough to get the job done.
  • Hooked tip latches onto locknut and maximizes turning leverage.
  • Kit contains one ½ inch wrench (LNW-500) and one ¾ inch wrench (LNW-750).
Check Stock

CARTMAN 9-Way Internal/External Slide Hammer Puller Set - Pulls Hubs, Rear Wheel Axle Shafts, Bearings, Bushings, Seals, Retainers

  • Ideal for internal and external pulling on bearing cups, stubborn oil seals, Bushings, and many press fitted parts. Features: Internal and External Three Leg and Two Leg jaw puller yokes.
  • 5lb. Slide Hammer, 425mm long, M16*1.5mm UNF thread.
  • Front Hub puller, Rear Axle puller, Locknut Cone.
  • Dent puller screws (large and small), Supplied in blow mold storage case..
  • Features: Internal and External Three Leg and Two Leg jaw puller yokes..
Check Stock

LITTLE GIANT DuraFork Pitch Fork Replacement Head (Green) Durable Polycarbonate Stable Fork Head with Angled Tines (Item No. PDF103GREEN)

  • POLYCARBONATE CONSTRUCTION - This stable fork heads' polycarbonate design offers superior flexibility and strength..
  • ANGLED TINES FOR LESS SPILLING - The pitch fork head has angled tines result in less spilling through the tines of the fork and overall less mess..
  • FORK DIMENSIONS - This pitch fork head's tines are 13.125 inch long by 15.125 inch wide..
  • NYLON LOCKNUT ATTACHMENT - The pitchfork head attaches to the handle by nylon locknut that offers firm attachment to the pitchfork handle..
  • COLOR OPTIONS AVAILABLE -These pitch fork heads come in several colors included: Berry Blue, Black, Blue, Burgundy, Green, Hot Pink, Lime Green, Orange, Purple, Red, Teal..
Check Stock