Reviews Ceramic Gas Igniter

Round Gas Range Oven Ignitor for GE 41-208 ER4342528 SGR401 SGR400

  • Gas Igniter for Stove Range, Replacement Part No. SGR403.
  • SPECS:This igniter’s amperage range is 2.5 – 3.0. Used with 2.8 to 3.0 amp rated gas safety valves.The ignitor measures 3-1/2 long,one lead has a 1/4 female terminal the other is bare. 2 ceramic wire nuts included,This is a direct replacement for GE number WB2X9154, WB13K3, WB13K4,Fits many different range manufactured including Whirlpool, Kenmore, Roper..
  • Includes: high temperature stainless steel shield, high temperature MGT wire leads, and high temperature ceramic wire nuts to wire into original harness. Replaces long and short ignitors. Be careful not to drop your new ignitor.
  • ignitors are fragile and will break easily..
  • Description:The oven igniter, also called a glow bar, heats up the bimetal switch and causes the oven to ignite the gas fed to the burners. A common issue when the oven fails to ignite is a faulty glow bar. If the oven does not start within 90 seconds, the glow bar is likely the issue. Do not be fooled if the glow bar turns red. If it does not reach the appropriate temperature, the oven will not light. If your ignitor uses a connector on the end, reuse the connector from the old ignitor..
  • Description:Use your wire cutters to cut the wires on the old ignito....
Check Stock

Gas Oven Bake & Broil Round Igniter for WB2X9154 4342528 Ignitor AP2014008, PS243425

  • Gas Igniter for Stove Range, Replacement Part No. SGR403.
  • SPECS:This igniter’s amperage range is 2.5 – 3.0. Used with 2.8 to 3.0 amp rated gas safety valves.The ignitor measures 3-1/2 long,one lead has a 1/4 female terminal the other is bare. 2 ceramic wire nuts included,This is a direct replacement for GE number WB2X9154, WB13K3, WB13K4,Fits many different range manufactured including Whirlpool, Kenmore, Roper..
  • Includes: high temperature stainless steel shield, high temperature MGT wire leads, and high temperature ceramic wire nuts to wire into original harness. Replaces long and short ignitors. Be careful not to drop your new ignitor.
  • ignitors are fragile and will break easily..
  • Description:The oven igniter, also called a glow bar, heats up the bimetal switch and causes the oven to ignite the gas fed to the burners. A common issue when the oven fails to ignite is a faulty glow bar. If the oven does not start within 90 seconds, the glow bar is likely the issue. Do not be fooled if the glow bar turns red. If it does not reach the appropriate temperature, the oven will not light. If your ignitor uses a connector on the end, reuse the connector from the old ignitor..
  • Description:Use your wire cutters to cut the wires on the old ignito....
Check Stock

MCAMPAS Igniter Ceramic Electrode Replacement Part .27.56-inch Ignitor Wire &Ceramic Spark Plug Ignition ​Electrode for Fire Pit Burner Gas Grill Burner ​2 Pack​

  • ➦2 Pieces ：27.56 inch(700mm) Ignitor Wire with M10*1 Ceramic Electrode length 55mm,product high temperature 200°C.
  • ➦Universal spark with M10*1 thread includes two nuts to fix on your fire pit pan plate.
  • ➦Please note that the connection to the igniter is circular, suitable for pressing the igniter.
  • The end of the terminal is in round with 2.3mm....
  • ➦Igniter ceramic electrode universally fit for many fire pit table pan,also fit BBQ grill burner, gas stove, grill, heater.Please check and compare....
  • ➦Made of high quality material ensure safe and long-lasting performance. There is a heat resistance coating over the wire to ensure safe use. will....
Check Stock

MENSI Flame Starter Push Button Piezo Kit Grill Replacement Ignitor for Weber 80462 Q100 Q200, for New Weber Traveller Griddle BBQ Parts

  • ※- The Piezo Push Button Igniter Kit is a specific and dimensions for the Weber Traveller Grill and Q100 Q200 Gas Grill, Replacement of Weber 80462.
  • ※- Parts of Igniter is a push ceramic piezo type, serval push creat a spark.
  • ※- Compatible with 516001 Weber Q120, 566001 (2006) Weber Q220 , 386001 Weber Baby Q100, 386002 (2008) Weber Q100, 396001 Weber Q200, 396002 (2008) Weber Q200, 396004 Weber Q200 Gas Grill. etc.
  • ※- Fits Weber Q100 .Q200 .Q120 .Q220 .Q1000 .Q2000 Gas Grill Models.
  • ※- Easy install and operate to spark the electrode to ignite the propane or natural.
Check Stock

MCAMPAS Universal Silicon Nitride Hot Rod Ignitor.120 Volt Nitride Igniter Replacement For Silicon Carbide Igniters of The Gas-Fired Forced-Air Furnaces, Water Heaters, Boilers

  • 120 volt nitride furnace igniter Replaces hot surface ignitor for gas-fired furnace, boiler, and water heater.
  • How to tell if your igniter is working， if the igniter has continuity your multimeter should read anywhere from 9 to17 Ohms,if there is no reading on the multimeter or very little change, then there is no continuity and you will have to replace the nitride furnace igniter.
  • 1.97" Nitride heating element, 1.18"Ceramic insulator body nonglazed 95% alumina- polished finish, 15-3/4 inch temperature rating 250℃ cable- 20 AWG/ UL 10362 specification.
  • It works compatible with Cook Top, Cook Top and Range, Furnace and Warm Air Movement, Gas Ignition, Hot Surface Igniters, Infrared light source, Pool Heater and Boilers, Process Machinery, Special FX, Water, and Parking Heaters Nitride heating element.
  • Power rating:150 W. Temperature at 120v ± 0.5v .60HZ at 17 sec ≧1180 ℃.This is a very versatile product, very robust with long cycle life. Silicon nitride is extremely rugged and can be handled without fear of breakage or contamination..
Check Stock

Exact Replacement Igniter for Samsung NX58H5600SS/AA-0000 NX58H5650WS/AA-0000 Range Oven

  • Gas Range Oven Igniter part number 41-230..
Check Stock

RCK Sales Members Mark Gas Grill SAMS Club Charbroil Igniter Collector Box with Electrode 3 Three Pack

  • Members Mark Gas Grill Sams Club Igniter Collector Box with Electrode (3) Three Pack.
  • Collector Box and Ceramic Electrode Assembly (3) Pack of Igniters included with same.
  • Over all Size: 3 7/8" x 1 1/4" Threaded section 2 1/8" 1/2" Probe at bottom Has a round male end connector at the bottom of igniter.
  • Grill Chef SS525-B, SS525-BNG, SS639, SS72B Fits Char-broil 4632215,463221503,4632220,463323503 Ken-more....
  • Alway Measure and compare your old igniter to the replacements.
Check Stock

ATKKE 67726 Igniter Kit for Weber Genesis 300 Series Electronic Ignitor Kit with Side-Control Battery Ignition Starter Part 2007 Models Gas Grill for Weber Genesis 310 320 Series Grills Replacement

  • GENESIS 300 SERIES ELECTRONIC IGNITOR KIT - Genesis 300-E and 300-S Series (Model Year 2007) ignitor kit. The distinctive part in this kit is the....
  • PACKAGE INCLUDED - This igniter kit includes one white ceramic U-shaped spark device with electrodes and wires, one electronic igniter module and one....
  • HIGH QUALITY MATERIAL FOR DURABLE AND LONG-LASTING - This igniter kit is made of premium plastic, metal and ceramics. All the components are durable....
  • AN EFFECTIVE WAY TO RE-ACTIVE YOUR GAS GRILL - Nothing beats using a gas grill to make quick and delicious foods while the ignition system plays an....
  • EASY TO INSTALL - The installation is simple and easy. Please prepare a screwdriver in advance. Just remove a couple of screws then you can remove the....
Check Stock

Universal Ignitor, 120V Silicon Nitride Hot Rod Ignitor Replacement for Silicon Carbide Igniters of Gas-Fired Forced-air Furnaces, Water Heater and Boiler, Nitride Heater Igniter

  • ...eading or changing small(if the igniter has continuity, then your multimeter should read between 9 - 17 ohms), and you have to replace the nitride igniter.
  • Materials: Consists of stainless steel 304 bright finish bracket, 1.97" nitride heating element, 1.18" ceramic insulator body, non-glazed 95% aluminia polished finish, 15-3/4" 20AWG/ UL 10362 specification 250°C temperature-resistance cable.
  • Hot Side Ignitor/Igniter Specification: Rated voltage: AC 120V +/- 10%-15%, 50/60HZ, Cold resistance: 9-17Ω, Rated power: 150W, Temperature at 120v ± 0.5v. 60HZ at 17 sec ≧1180 ℃, Anti-overvoltage ability: igniter energized for 1 minute -132V. Igniter current not allowed to increase from 30 seconds to 60 seconds, the front required to move the stand is 10 lbs, Minimum≧5kgf.
  • Easy to Install: Very simple, strong structure, not easy to damage, use high-quality packaging, waterproof and drop-proof, ensures that you can receive the perfect igniter. If you have any questions, you can contact us in time, we will reply within 12 hours.
Check Stock

MENSI 11.8” Long Grill Replacement AA Igniter With Electrode Wire High Effiency Pulse Ignition Kit

  • AA battery type igniter one exit with ceramic electrode wire 300mm (battery is not included).
  • Grill replacement ignition part thin type igniter can save more space in your grill.
  • Red push button just small force and many sparks more effiecient.
  • 18mm mounting hole threads on your grill.
  • CSA Certified, Durable and Lasts Longer, Universal Spark generator BBQ Gas Grill Replacement.
Check Stock