Reviews Calibration Block

Lange Skinfold Caliper with 5-Step Calibration Block, Compact Hard Case, and Instruction Manual with Charts to Measure and Calculate Body Fat Percentage, 1.0 mm Accuracy, Professional Quality

  • INCLUDES Lange skinfold caliper, 5-step calibration block, instruction manual with charts, and hard case..
  • COMPACT, EASY, DURABLE DESIGN Compact design fits easily in your bag for conventient and secure transport with the hard case. The Lange caliper has an easy to read dial that gives you accurate and consistent readings..
  • 5-STEP CALIBRATION BLOCK for testing will ensure your caliper is calibrated and your readings are accurate..
  • CONSTANT PRESSURE The metal spring provides constant pressure to ensure accurate readings throughout the full measurement range..
  • SPECIFICATIONS: 60mm range, 1mm increments, +/- 1.0mm accuracy..
Check Stock

HHIP 8902-0155 35-55 HRC Rockwell Standard Test Block

  • Can be used with 8902-0150 Hardness tester and most other imported Hardness testers.
  • Each block is marked with the specific measured value..
  • Supplied with a calibration certificate from the factory..
Check Stock

81 PCS/SET SQUARE GAGE BLOCK SET w.NIST Equivalent certificate, GRADE B

  • 81 PCS/SET SQUARE GAGE BLOCK SET w.NIST Equivalent certificate, GRADE B.
  • Description: 81 pcs/set steel precision SQUARE gage block set, grade B--w. tollerance of 50 millionth of inch. All block mirror polished, with serial number and size, WITH GAGE HOLE Complete with NIST equivalent certificate of calibration showing deviation of each block. Meets or exceed Fed. Spec. GGG-G-15C and Conform to MIL-STDD-45662A.
  • 9 blocks: .1001" - .1009" in .0001" steps 49 blocks: .101" - .149" in .001" steps 19 blocks: .050" - .950" in .050" steps 4 blocks: 1.000" - 4.000" in 1.000" steps Fitted in heavy duty and precision made wooden box..
Check Stock

CEM BX-150 Dry-Well Temperature Calibrator 33°C to 300°C

  • The calibrator can operate at very high temperature . Precautions must be taken to prevent personal injury or damage to surrounding objects . probes may be hot when removed from the units and should be placed on a heat resistant surface . The unit may remain hot for several minutes after switching off .Do not switch off if temperatures above +100℃. Allow to cool before storage ..
  • Caution must be taken when removing probes and inserts from the units . if the unit is set at a high temperature the inserts will be very hot and could cause burns probes and inserts only on a suitable heatproof surface ..
  • Only place temperature probes in dry-block holes . These units are designed to be operated dry . Do not sprinkle and liquid into any of the dry-block holes ..
  • These dry-blocks are designed to be rugged and durable but do contain electronics. Do not operate in dirty , dusty or very damp enviroment or near liquids that could present a hazard from electric shock..
  • The units are ideal for use in a variety of industrial and process applications .Each unit is supplied with a traceable certification of calibration of calibration showing actual test data , which can be used as part of quality assurance programmes ..
Check Stock

Traceable Excursion-Trac™ Data Logging Thermometer with Calibration; 1 Bottle Probe

  • ...uration. The TL2-A is two thermometers in one instrument, with two channels allowing simultaneous temperature measurement in different locations. The TL2-A is well suited for establishing temperature traceability in equipment that requires high accuracy. The TL2-A is also perfect for metrology applications and as a calibration reference thermometer..
  • The TL2-A can be ordered with sensors included or the user can provide their own sensors. Sensor coefficients can be entered from a PC making it easy to change from a daily use RTD to a SPRT including user selectable choice of ITS-90 or Callandar-Van Dusen equations. Units come with 5 point resistance calibration from 20 to 425 ohms. With available PRT(s) ThermoProbe can provide a temperature reference system. Standard sensors are 100Ω wire-wound platinum RTDs in a stainless steel ¼” sheath 13.
  • The intuitive user interface allows easy configuration of temperature units, display resolution and a relay output. Minimum, maximum and average temperatures are automatically stored to memory for later reference. The interface allows viewing of Highest, Lowest and Average Readings, Zero Offset adjustment for sensor drift and readings in C, F, K and Ohms. The versatile data logging feature can be used to s....
Check Stock

AT4516 16 Channel Digital Thermometer High Temperature Data Logger Temperature Chart Recorder

  • ...uration. The TL2-A is two thermometers in one instrument, with two channels allowing simultaneous temperature measurement in different locations. The TL2-A is well suited for establishing temperature traceability in equipment that requires high accuracy. The TL2-A is also perfect for metrology applications and as a calibration reference thermometer..
  • The TL2-A can be ordered with sensors included or the user can provide their own sensors. Sensor coefficients can be entered from a PC making it easy to change from a daily use RTD to a SPRT including user selectable choice of ITS-90 or Callandar-Van Dusen equations. Units come with 5 point resistance calibration from 20 to 425 ohms. With available PRT(s) ThermoProbe can provide a temperature reference system. Standard sensors are 100Ω wire-wound platinum RTDs in a stainless steel ¼” sheath 13.
  • The intuitive user interface allows easy configuration of temperature units, display resolution and a relay output. Minimum, maximum and average temperatures are automatically stored to memory for later reference. The interface allows viewing of Highest, Lowest and Average Readings, Zero Offset adjustment for sensor drift and readings in C, F, K and Ohms. The versatile data logging feature can be used to s....
Check Stock

Traceable Memory-Loc Dual Zone Temperature Monitoring & Data Logger Kit (TM-6441)

  • ...uration. The TL2-A is two thermometers in one instrument, with two channels allowing simultaneous temperature measurement in different locations. The TL2-A is well suited for establishing temperature traceability in equipment that requires high accuracy. The TL2-A is also perfect for metrology applications and as a calibration reference thermometer..
  • The TL2-A can be ordered with sensors included or the user can provide their own sensors. Sensor coefficients can be entered from a PC making it easy to change from a daily use RTD to a SPRT including user selectable choice of ITS-90 or Callandar-Van Dusen equations. Units come with 5 point resistance calibration from 20 to 425 ohms. With available PRT(s) ThermoProbe can provide a temperature reference system. Standard sensors are 100Ω wire-wound platinum RTDs in a stainless steel ¼” sheath 13.
  • The intuitive user interface allows easy configuration of temperature units, display resolution and a relay output. Minimum, maximum and average temperatures are automatically stored to memory for later reference. The interface allows viewing of Highest, Lowest and Average Readings, Zero Offset adjustment for sensor drift and readings in C, F, K and Ohms. The versatile data logging feature can be used to s....
Check Stock

Dry Block High Temperature Calibrator Range 50 to 650°C with Thermocouples T J K N R S for Calibration Labs Pharmaceutical Divisions Thermal Plants Metallurgical Plants Model AI-DBC-02

  • Supply Scope: 1 Unit of DBC-02 Dry Block Calibrator, Power Cable, 1 Unit of Test Lead (2 Wire), Insertion Tube: Dual Hole - 1 x 1/4” + 1 x 12.5 mm, Dual Hole - 1 x 1/4” + 1 x 8.2 mm, 1 Unit of Insertion Tool, 2no.s of 6A Spare Fuses, Instruction Manual and Factory Calibration Certificate | Applications: Calibration Labs, Pharmaceutical Divisions, Thermal Plants, Metallurgical Plants.
Check Stock

ThermoProbe TL2-A Precision Bench-top Laboratory Reference Thermometer – Dual Channel & USB Data Logger

  • ...uration. The TL2-A is two thermometers in one instrument, with two channels allowing simultaneous temperature measurement in different locations. The TL2-A is well suited for establishing temperature traceability in equipment that requires high accuracy. The TL2-A is also perfect for metrology applications and as a calibration reference thermometer..
  • The TL2-A can be ordered with sensors included or the user can provide their own sensors. Sensor coefficients can be entered from a PC making it easy to change from a daily use RTD to a SPRT including user selectable choice of ITS-90 or Callandar-Van Dusen equations. Units come with 5 point resistance calibration from 20 to 425 ohms. With available PRT(s) ThermoProbe can provide a temperature reference system. Standard sensors are 100Ω wire-wound platinum RTDs in a stainless steel ¼” sheath 13.
  • The intuitive user interface allows easy configuration of temperature units, display resolution and a relay output. Minimum, maximum and average temperatures are automatically stored to memory for later reference. The interface allows viewing of Highest, Lowest and Average Readings, Zero Offset adjustment for sensor drift and readings in C, F, K and Ohms. The versatile data logging feature can be used to s....
Check Stock

ThermoProbe TL2-A Precision Bench-top Laboratory Reference Thermometer – Dual Channel & USB Data Logger

  • ...uration. The TL2-A is two thermometers in one instrument, with two channels allowing simultaneous temperature measurement in different locations. The TL2-A is well suited for establishing temperature traceability in equipment that requires high accuracy. The TL2-A is also perfect for metrology applications and as a calibration reference thermometer..
  • The TL2-A can be ordered with sensors included or the user can provide their own sensors. Sensor coefficients can be entered from a PC making it easy to change from a daily use RTD to a SPRT including user selectable choice of ITS-90 or Callandar-Van Dusen equations. Units come with 5 point resistance calibration from 20 to 425 ohms. With available PRT(s) ThermoProbe can provide a temperature reference system. Standard sensors are 100Ω wire-wound platinum RTDs in a stainless steel ¼” sheath 13.
  • The intuitive user interface allows easy configuration of temperature units, display resolution and a relay output. Minimum, maximum and average temperatures are automatically stored to memory for later reference. The interface allows viewing of Highest, Lowest and Average Readings, Zero Offset adjustment for sensor drift and readings in C, F, K and Ohms. The versatile data logging feature can be used to s....
Check Stock