Reviews Brinell Hardness Testers

Hardness Testing File Set

【Accurately measured value】-----Precision measurement circuit to ensure Indication error ± 0.5% (HLD = 800), showing the value of repeatability 0.8%.
【Leeb hardness measurement】-----Based Leeb hardness measuring principle, can detect a variety of metal materials.
【Supports a variety of standard hardness】-----Real-time display and conversion: Brinell HB, Rockwell HRC, Vickers HV, Shaw HS, and three kinds of intensity values.
【Applicable Materials】-----Steel and cast steel, alloy tool steel, stainless steel, gray cast iron, nodular cast iron, cast aluminum alloy, copper zinc alloys (brass), an alloy of copper and tin, copper(bronze).
【Application】-----1)Bearings and other parts.
2)Failure analysis of pressure vessel, steam turbine generator group and equipment.
4)Mechanical or permanent assembly installed.
6)The original record of formal requirements on test results.

Can be used with 8902-0150 Hardness tester and most other imported Hardness testers.
Each block is marked with the specific measured value..
Supplied with a calibration certificate from the factory..

Monstrum Pro Series scope rings are crafted from 7075 aerospace aluminum - providing greater tensile strength, shear strength, and Brinell hardness than typical 6061 aluminum scope rings.
Comes with stainless steel Torx mounting hardware, including a T25 Torx Plus wrench and a T25 Torx Plus Bit, for easy precision mounting without stripping of bolts.
Pro Series scope rings are treated with a Type III Hard Anodized Finish versus a Type II for previous generation scope rings for added protection against scratches and blemishing.
Available in 1 inch or 30 mm diameter. Compatible with both Picatinny or Weaver mounting bases..
All Monstrum products are now protected by Monstrum’s lifetime guarantee.

Monstrum Pro Series scope rings are crafted from 7075 aerospace aluminum – providing greater tensile strength, shear strength, and Brinell hardness than typical 6061 aluminum scope rings.
Comes with stainless steel Torx mounting hardware, including a T25 Torx Plus wrench and a T25 Torx Plus Bit, for easy precision mounting without stripping of bolts.
Pro Series scope rings are treated with a Type III Hard Anodized Finish versus a Type II for previous generation scope rings for added protection against scratches and blemishing.
Available in 1 inch or 30 mm diameter. Compatible with both Picatinny or Weaver mounting bases..
All Monstrum products are now protected by Monstrum’s lifetime guarantee.

Ideal for a wide variety of parts that don't require more expensive heat treated steels, such as stripper plates, jigs, fixtures, machine and component parts, templates, etc.
This steel can be carburized or case hardened After hardening, its physical properties, especially tensile strength, yield point, and Brinell hardness, are substantially higher.
The Starrett Company uses its own ground flat stock for many of its precision tool parts.
Full-length identification eliminates confusion with other steels.
Starrett A2 Tool Steel precision ground flat stock is a 20 carbon fine-grained, killed steel, which can be carburized or case hardened very similar to AISI 1018.

Handles have heavy vinyl grips with flat grips ends for 90-degree cuts.
All-purpose, center-cut jaws for soft, medium, and hard metals.
Forged, alloy tool steel jaws are precision ground for sure, efficient cutting and long life.
Lockplate reinforcement prevents jaw bolts from loosening or turning, keeps jaws in correct alignment.
Cutting capacities for soft and medium materials is up to Brinell 300, Rockwell C31.
Cutting capacities for hard materials is up to Brinell 400, Rockwell C42.

Testers are even more discounted than the fancy boxed versions and are great if you don't have a need for the fancy packaging. Testers are 100% authentic, fresh and completely full just like the original fragrance, however they are meant for the counter in a department store. Testers often come in a plain white box but sometimes they do not have a cap or box.The savings on the packaging means you save even more!.

Accurate measurement: In order to improve the accuracy of voltage measurement,Battery capacity testers circuit is specially designed for DC bias. When the terminal is not connected at all, it will display a small voltage, which does not affect the actual measurement.
Size:Discharge testers board size is 5x3.4 cm/1.97x1.34 inch, small, easy to carry and store.
Power supply voltage:Battery capacity meters power supply voltage: DC4.5-6V (micro USB interface), working current: less than 70mA. Supported current: no more than 3.000A resolution 0.001A.
Discharge voltage:Battery meter testers discharge voltage: 1.00V-15.00V, resolution 0.01V. Termination voltage range: 0.5-11.0V.
Battery capacity:Battery meters battery capacity range: 9999Ah (1Ah=1000mAh). When the value is large, it is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it reaches 10Ah, it is displayed as XX.XX..