Reviews Breadboard Circuit Board

BOJACK 3 Values 130 Pcs Solderless Breadboard 4 Pcs 830 Tie Points & 400 Tie Points & 126 Pcs Flexible Breadboard Jumper Wires

  • BOJACK high quality Solderless Breadboard Assortment Kit.
  • Breadboard is a solderless device for temporary prototype with electronics and test circuit designs. Most electronic components in electronic circuits can be interconnected by inserting their leads or terminals into the holes and then making connections through wires where appropriate..
  • The breadboard has strips of metal underneath the board and connect the holes on the top of the board. Note that the top and bottom rows of holes are connected horizontally and split in the middle while the remaining holes are connected vertically..
  • The Breadboards Can be Spliced According to the Unit, the Structure is Clear in Color..
  • Material: ABS Plastic Panel, Tin Plated Phosphor Bronze Contact Sheet..
Check Stock

kuman Raspberry Pi 4 B Holder Breadboard Kit, 7 in 1 RAB Holder kit Compatible for Arduino, Mega 2560 & Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero and Zero W

  • This 7 in 1 RAB Holder kit is designed by Kuman for the Raspberry Pi and for Arduino hobbyists, the holder is large enough for a Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, for Arduino or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard(for Arduino rapsberrry pi motherboard and 400 breadboard are not included)..
  • Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard..
  • Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W..
  • This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails..
  • Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1k resistors, a screwdriver, and some screws..
Check Stock

ACEIRMC 3pcs ESP32 Breakout Board GPIO 1 into 2 for 38PIN Narrow Version ESP32 ESP-WROOM-32 Microcontroller Development Board

  • Only suitable for 38PIN narrow version ESP32 without mounting holes, not suitable for other versions..
  • This breakout board can expand one GPIO pin of esp32 development board to two, which is convenient for users to reuse all pins in smart home projects. Nice breadboard alternative..
  • 2 TYPE CONNECTIONS， Pin Header & Screw Terminal. Just select them according to your purpose..
  • The expansion board is a double-layer board. One pin is wired on both sides. Therefore, the circuit is stable and highly reliable, and there will be no poor circuit contact and unstable signal transmission..
  • The board of this version has been soldered completely. No need to solder parts by yourself, which is very convenient to use..
Check Stock

DaFuRui Breadboard Jumper Wire Kit with 400-Point Breadboard、65pcs Multiple Sizes M/M Bread Board Jumper Wire、140 Pieces 2-125 mm U-Shape Preformed Jumper Wire Kit

  • ★【Excellent Quality】The kit is ideal for setting up a trial circuit, prototype or experimenting.A variety of colors, lengths, can be classified....
  • ★【Powerful Function】400 tie-points Solderless Breadboard, With self-adhesive tape on the back for easy bonding.65pcs 4.4in 6.3in 8.3in 10.3in....
  • ★【Easy to Install】The Breadboard Helper includes 2/5/7/10/12/15/17/20/22/25/50/75/100/125 MM 14 different lengths.Different colors: 140Pcs long....
  • ★【Widely Used】Can be used for wiring of breadboard circuits or where power or circuit connections.Proto-Typing Circuit，Electronic，Electrical....
  • ★【Package Content】1PCS 400 tie-points Solderless Breadboard，65PCS long and short solderless breadboard jumper kit，140Pcs 14 different....
Check Stock

UNIROI Raspberry Pi RAB Holder Breadboard Kit with 830 Points solderless Circuit Board Raspberry Pi Holder for Arduino, Mega 2560 & Raspberry Pi 4B, 3B+, 3B, 2B and 1B+, A+ (52 Items)

  • This 14 in 1 RAB Holder kit is designed by for the Raspberry Pi and Arduino hobbyists, the holder is large enough for a Raspberry Pi 4B/ 3B/ 2B/ 1B+/ Zero/ Zero W, Arduino 328P Control Board or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard.
  • Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W..
  • This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails..
  • Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1k resistors, a screwdriver, and some screws..
  • Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard..
Check Stock

Yahboom Breadboard Dupont Wire Multicolored Jumper Wires 40pin M-F, 40pin M-M, 40pin F-F, 3PCS 830 Point Solderless Prototype PCB Board for Arduino Raspberry Pi Electronic Project

  • 【Pure Copper Breadboard Jumper Wires】40 colored 1 row, 40 composed of 10 colors, can be disassembled for use, PVC material, high temperature resistant wire, more safe and durable.The two ends of the wire are designed with quick wiring ports, which can be used for circuit quickly without soldering..
  • 【120pcs 3 Types M-F M-M F-F】Separable multicolored (10 colors) softness ribbon cables, Each cable length: about 20cm /8-inch.
  • 【3PCS Spliceable Breadboards Kit 830 Point】165×55×10mm,630+200=830 holes，1 terminal strip: 630 jacks，2 distribution strips: 200 jacks，Matching jumper, wire diameter 0.8mm.
  • 【MB-102 ABS Recyclable Experimental Connection Board】White ABS Plastic Body with Black Printed Legend. Color Legend on Distribution Strips.With Self-Adhesive Tape on the Back, Easy to Stick on the Arduino Prototype Shield..
  • 【Application】Good for A-rduino Breadboard Jumper Wires kit Project and other Electrical DIY kits.DIY experiment / Electronic projects / Breadboard / PC motherboard / PCB project.
Check Stock

Treedix Breakout Board Module with Pin Board for Teensy 4.1/3.5/3.6 Compatible with Arduino

  • The breakout board expands the connection with all the processor functions, the circuit board is well-made, gold-plated on both sides to prevent oxidation.
  • Simple and easy to assemble, it can be used in conjunction with a breadboard, the distance between the holes on the board is 2.54mm.
  • Widely compatible: all pins on the breakout board are accessible, and can be used in conjunction with Arduino IDE and Arduino compatible hardware.
  • Use this breakout board module to easily extend Tennsy 4.1 project to industrial control, home automation or other applications.
  • Note: The package is not include teensy development board.
Check Stock

eBoot 3 Pieces 400-Point Solderless Circuit Breadboard with 65 Pieces M/M Flexible Breadboard Jumper Wires

  • Breadboard with jumper wire set: 3 pieces 400-point solderless circuit breadboard.
  • 65 Pieces male-male flexible breadboard jumper wires.
  • Easy to use: the breadboard is made of ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling.
  • Breadboard: plug and play, 400 tie points, peelable adhesive tape backing.
  • You had better clean the place you want to stick firstly, to make a good....
  • Breadboard jumper wires: good conductivity, it's hard to drop the head of the wire, can be applied repeatedly.
  • Compatible with electronic and electrical experiments.
  • The jumper wires are easy to insert into the breadboard.
Check Stock

MEGA2560 Screw Terminal Block Breakout Module with Aluminum Enclosure, for Arduino MEGA 2560 R3

  • Screw connection will hold tightly.Solder good,holds both stranded and solid copper wires secure.Fits good in circuit board,doesn't twist and break when the screws are tightened,will not lose or slip around.The leads are aligned for a standard breadboard and fit securely.The pins themselves are slim enough to fit through the holes,doesn't destroy the plating on the inside..
  • Won't lead to strip screw heads,broken solder joints or poor connections.Makes good electrical contact,looks good and neat.Not allow the wire to get off-center when inserted.The connector will not melt things when soldered to them.They are not too thick that fit perfectly next to each other on a protoboard.You can jam them in there and they sit parallel..
  • Easy to insert into prototype boards and solder the pins.These connectors work well on PCBs.Can be used on a breadboard power rails if plugged in at an angle.The screw connections can open enough to let a wire enter freely,doesn't make it difficult to enter and tighten the wires.Make it easier to swap out things like simple antennas,low voltage power sources,sensors,ect..
  • Needn't over-torque the screws and they will hold up fine.When you want to move wires,wires come right out with the slightest movement.Great for mounting on or in ....
Check Stock

WayinTop RPi GPIO Breakout Expansion Kit for Raspberry Pi 4B 3B+ 3B 2B B+, T-Type GPIO Expansion Adapter Board + 830 Tie Points Solderless Breadboard + 40pin GPIO Flat Ribbon Cable + 65pcs Jumper Wire

  • 【Updated Starter Kit for Raspberry Pi】This is a updated Assembled starter kit for for Raspberry Pi 4B/3B+/3B/2B/B+, including GPIO Adapter Board with Wiring Diagram Card, 40pin GPIO Rainbow Fat Cable, 830 Tie Points Solderless Breadboard and 65pcs Jumper Wire..
  • 【GPIO Adapter Board with Wiring Diagram Card】You can connect much version raspberry of the board to various sensors and electronic components with the GPIO extension board..
  • 【40pin GPIO Rainbow Fat Cable】IDC 40pin Male to Female Ribbon Cables Kit flat GPIO Cable.
  • Material: High-quantity copper soft wire material for safe and durable.
  • Easy assembly:The cables can be separated to form an assembly wires to support non-standard odd-spaced headers to complete other tests..
  • 【830 Tie Points Solderless Breadboard】made of high quality ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling, with self-adhesive tape on back and multiple links to buckle..
  • 【65pcs Flexible Jumper Cables】Flexible, durable, reusable, easy to connect and disconnect.
  • 4 Kinds of length: 12cm(49pcs), 16cm(8pcs), 20cm(4pcs), 24cm(4pcs).
  • these jumper cable wires can connect each other through the pin connection, do not need welding, can fit for fast circuit....
Check Stock