Reviews Band Saws Jet - BestBuyersPro.com

Jet JWBS-14DXPRO Wood Band Saw Blade Thrust & Guide Bearings. Set of 10 BB-608ZZ

For hard or soft wood, plastic, mild steel and non-ferrous metal.
For all vertical, stationary, floor standing 2-wheel band saws.
These are heavy duty, durable, commercial grade band saw blades for industrial, woodworking, DIY and professional craftsmen.
82" long fits 12″ Delta 28-190 & Jet JWBS 120 S.

For hard or soft wood, plastic, mild steel and non-ferrous metal.
For vertical, stationary, floor standing 2-wheel band saws.
These are heavy duty, durable, commercial grade band saw blades for industrial, woodworking, DIY and professional craftsmen.
Length 931⁄2″: Fits all 14″ Delta/Rockwell, Jet, Rikon, Steel City, General, Ridgid, older Sears Craftsman, Grizzly, Bridgewood, Woodtek,etc..

Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
Make sure your insert recess has the locating pin on the side, not on the rear..
use on 14" Band Saws and 24" Scroll Saws.2&1/2" X .100 thick Please measure your saws recess to ensure proper fit.
They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
use on 14" Band Saws and 24" Scroll Saws..
2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
Make sure your insert recess has the locating pin on the side, not on the rear.
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

use on 14" Band Saws and 24" Scroll Saws.Table Inserts (pack of 2). Material: Aluminum.
They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
Make sure your insert recess has the locating pin on the side , not on the rear.
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Please measure your saw as some Delta & Rockwell 14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required..

Saws that use 44-7/8 in. Blades.These tires are 6 inches outside diameter and 1/2 inch wide..
Replacement rubber tire for Milwaukee electric corded band saws NOT the battery cordless ones..
These tires should fit any model of Milwaukee band saw 6225, 6226, 6230, 6230N, 6232-6, 6232-6N, 6236, 6236N, 6238N, and 6238..
These tires will also fit DeWalt band saw model DW328, DW328K, DW 329, DW329K, and D28770 type 1.These tires will also fit Porter Cable Porta-Band saws model 725, 726, 736, 7723, 7724, and 9725. The Porter Cable part number is AO2807..

LIFETIME ASSURANCE : All our accessories for sanders, planers, sharpeners, band saws, compressors, drills, including bearings, guide bearings, thrust bearings, drill chucks, drive belts, arbors and band saw tires are backed by top-notch service and EVERLASTING commitment..
MADE IN THE USA : Every single drill chuck and arbor is EXCLUSIVELY designed and produced in the USA in line with the highest quality standards. Choose our smooth bearing replacement for dependable performance..
WIDE COMPATIBILITY : DNLK drill chucks and arbors are compatible with most brands. Order our heavy duty drill chucks and profit from reduced downtime and maintenance..
SUPREME DURABILITY, WEAR RESISTANCE : In addition to a tight fit and flawless operation, our drill chucks and arbors have been tested and have proven to withstand high shocks and heavy-duty loads in both cold and hot environments..
DNLK drill chuck will fit Jet 1440Vs Wood Lathe.

FUNCTION: A high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts.
FEATURES: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs that remove all side play from the bar, creating a perfect fit..
PRECISION: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
UNIVERSAL DESIGN: Works with most Contractor style, full sized saws, or tools with standard miter slots (3/4” width x 3/8” depth) with or without T-slots, making it compatible with popular brand table saws, band saws, router tables, disk and belt sanders. PLEASE NOTE : will not work with smaller saws or tool with 5/8” miter slots..

Allows for use of thin kerf table saw blade for non-through cuts..
Compatibility: Designed to fit Powermatic PM2000B table saws..
JET Red Assurance Guarantee: Backed by JET's industry-leading one-year warranty against manufacturing defects..