Reviews Axle Puller

ABN Front Wheel Drive Axle Pulley Attachment - CV Axle Removal Tool CV Joint Slide Hammer Adapter

  • [Remove Front Wheel Drive Axles Easily] To replace or repair your constant velocity (CV) axle joints, use the ABN Front Wheel Drive Axle Puller Attachment.
  • Inner CV axle puller designed to pull joints with hidden retaining rings from FWD vehicles.
  • [Works with Your Slide Hammer] The CV joint puller attaches to your slide hammer and allows you to create added torque to loosen and remove stubborn axle shafts and water pumps.
  • Fits slide hammers with 5/8-inch x 18 threads.
  • [Easy to Use] Attach the inner CV removal tool to your slide hammer then slide the adapter around the shaft behind the inner boot.
  • Use the slide hammer to create torque to pull out the axle.
  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Unlike pry bars or CV axle fork tools, the CV shaft slide hammer axle attachments focus the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Heat-treated CV puller adapter with black oxide finish ensures optimal strength and durability while r....
Check Stock

8MILELAKE Rear Axle Bearing Puller Extractor Installer Set Axle Bearing Removal Remover Tool Kit

  • [APPLICATION]: This rear axle bearing puller can help to pull out semi-floating rear axle bearings quickly and effectively..
  • [EASY TO USE]: The washer of the axle bearing puller can captures the bearing firmly to distribute the force to the whole bearing, can avoid damage of the bearings and case..
  • [DURABLE MATERIAL]: The rear axle bearing removal tool is constructed from heavy duty cast steel, which has good strength and durability, can provide long service life..
  • [SIZE]: The bearing puller remover set includes fittings for main bearing tube: Small: 1" to 1-7/8.
Check Stock

CARTMAN 9-Way Internal/External Slide Hammer Puller Set - Pulls Hubs, Rear Wheel Axle Shafts, Bearings, Bushings, Seals, Retainers

  • Ideal for internal and external pulling on bearing cups, stubborn oil seals, Bushings, and many press fitted parts. Features: Internal and External Three Leg and Two Leg jaw puller yokes.
  • 5lb. Slide Hammer, 425mm long, M16*1.5mm UNF thread.
  • Front Hub puller, Rear Axle puller, Locknut Cone.
  • Dent puller screws (large and small), Supplied in blow mold storage case..
  • Features: Internal and External Three Leg and Two Leg jaw puller yokes..
Check Stock

Orion Motor Tech Rear Axle Bearing Puller Tool Kit and Slide Hammer Set | Axle Seal and Bearing Remover Set with Slide Hammer Yoke and 3 Rear Axle Puller Adapters, 1\ to 2-7/8\ IDs

  • 8PC. SLIDE HAMMER SET: This 8-piece professional axle, bearing, and seal removal tool set by Orion Motor Tech provides a 5/8" slide hammer, yoke, locknut, hook, and adapters to let you quickly, easily, and safely repair rear axle problems on the vast majority of domestic cars and light trucks.
  • AXLE PULLER SET: Lock the slide hammer onto the 4-point yoke to set up a flange type axle puller that will let you extract parts with threaded holes, including stud axles, spur gears, and more.
  • SEAL PULLER SET: The 5.5 pound slide hammer and its sturdy T handle provide the firm grip and torque needed to pop out worn and damaged seals and other press fit parts using the included hook.
  • BEARING PULLER SET: The small, medium, and large bearing puller adapters cover inner diameters from 1 to 1-7/8.
Check Stock

VCT 23" Long 5lb Slide Hammer Inner CV Joint Puller

  • The set includes a 23-inch T-style slide hammers bar, a 5 lb hammer weight, a nut, and a 2-inch opening 2.5-inch depth slide hammer CV axle adapter. They will remove the axle assembly without damage on 1986 to current Taurus and Sable..
  • The slide hammer and puller design provide a straight and even pull to protect joint off damage. The round bead on the puller will stop the hammer so it can never hurt the hand pulling on T-shaped handle..
  • Our CV joint puller adapter and large slide hammer bearing puller will create added torque to impose a large pressure on CV axle. This tool set could easily loosen and remove stubborn CV axles in minutes..
  • The product is made of premium steel, all the parts have hardened and finished with high-temperature oxide to ensure superior durability and rust and corrosion resistance..
Check Stock

WINMAX TOOLS AUTOMOTIVE 18 Pc Heavy Duty Axles Slide Hammer Dent Panel Bearings Gears Seals Puller Set

  • SHIPPING-IT will be shipped within 24hs, delivery in 7-12 days. Contact us if any problems..
  • This professional quality Slide Hammer Puller kit is ideal for use within the automotive industry for pulling bearings, gears and front wheel drive axle shafts..
  • This heavy duty slide hammer has a 5 lb. hammer to pack real punch. The slide hammer puller set pulls flange-type rear axles and most front-wheel drive hubs and the internal and external jaws provide a variety of combinations to pull bearings, gears and seals. The pack contain versatile puller assortment to let you handle all kinds of pounding and pulling operations..
  • Accessories Included ·Slide hammer, ·2 and 3 jaw puller yokes, ·Internal/external puller arms, ·Wheel/axle puller yoke, ·Dent puller hook, ·Dent puller screws (large and small), ·Adapters and hardware, case.
  • Features/Specifications ·Material: steel, heat treatment ·5 lb. chrome plated steel slide hammer ·T-handle for secure grip ·Chrome-plated shaft for smooth operation ·Combination puller with 5-lb malleable steel slide hammer. ·Drop forged steel pullers and attachments fully hardened shaft and accessories. ·Converts into a 2 or 3 jaws internal/external puller for reaching right areas. ·Packed in a sturdy carry case.
Check Stock

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

JOMBULL 9-Way Slide Hammer Puller Set, 19 pcs Rear Wheel Axle Hub Dent Shaft Puller, Slide Hammer Bearing Puller for Hub Seal

  • 【Durable】 Our 9-way slide hammer puller set is made of heat-treated forged steel, polished and chrome-plated to resist rust and wear, extending the service life..
  • 【Application】 The axle hub dent shaft puller is widely used for flanged rear axles, most front wheel drive hubs, pulling dents and other press fit parts..
  • 【Easy to operate】 You only need to install the axle hub dent puller on the part you want to remove, when pulling the T-handle, transfer the force to the shaft, the shaft drives the connecting end to pull out the part, repeat the above steps, the hub or bearing will be easily removed..
  • 【What you get】 Our 9-way slide hammer puller set includes, slide hammer, puller head, pulling adapter, cross block, inner/outer pulling jaw, hex jaw nuts and screws (3pcs), Vise-Grip adapter (single lead thread), sealing hook, 3-way puller head, cone, self-tapping screw and retainer..
  • 【Safe storage】 The slide hammer bearing puller comes in a blow molded case, sturdy and durable, and each piece has precisely sized compartments, easy to store and carry..
Check Stock

E-cowlboy Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit,63mm 48mm CV Joint Fork Adapter,Heavy Duty 10 Pounds Slide Hammer

  • 【Slide Hammer Puller Set with Plastic Suitcase】: This kit include: 1 heavy duty slide hammer.
  • 2pc 16mm nut. this kit have everthing you need to remove CV axle or half shaft, all the tools put in a plastic case, easy to carry..
  • 【 Perfect Joint Fork】 ： This slide hammer puller set includes opening 63mm and 48mm CV joint fork disassembly adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have wide use..
  • 【Slide Hammer Made of Heavy Steel】The slide hammer and the CV joint fork is made of heavy-duty steel, which can withstand huge pressure without deformation, is not easy to break, and is more durable. The sliding distance is 19.5 inches, and the weight is 10 pounds .The overall ergonomic design of the slide hammer, the handle is curved, the surface is large, and it is more comfortable to use. Use this universal joint slide hammer to work more efficiently..
  • 【Quick to Remove CV Axle 】：With thi....
Check Stock

Sunluway - 12020-2 Pack Axle Popper Kit - Inner CV Axle Removal Tool Set - for Use on Front Wheel Drive Vehicles-Remove Most Vehicles’ Half-Shaft Drive Axles-Fix Damaged CV Joints

  • Easy to disassemble: Skip the complicated slide hammer puller sets and pry bar tools that can cause damage to your axle, use this CV shaft tool to easily disassemble the CV shaft, saving your time and energy !.
  • Material: CV Axle Removal Tool Set made of high-strength hardened steel, which has high hardness, high strength, with stable performance and reliable use and longer service life.
  • Benefits: Better and Safer than Using a Hammer and Bar because the wedge-shaped fork end of the axle Popper applies uniform pressure to both sides of the shaft To ensure safe release (Two piece CV axle popper tool kit ensures fitment for most FWD vehicles).
  • Easy installation: Insert the wedge wheel bearing tool between the transaxle case and the axle joint, and the fork head surrounds the axle end, tap the end of the front fork to release the axle shaft. these axle puller tools are simple, yet powerful, Is your essential tool !.
  • 100% Satisfaction Guarantee: If you're not 100% satisfied with our , please feel free to contact us, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty..
Check Stock