Reviews Avr Pic Programmer
SainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM
- 12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
- Indication LED's for Relay output status.
Check StockTegg 2PCS Flat Ribbon Cable 2.54mm Pitch 2 Row 10 Pin Female to Female Wires IDC Ribbon Connector 1m/ 3.3Ft
- Product name: Flat Ribbon Cable. Type: 2 Row 10 Pin..
- Cable long: 1m/ 39.4 Inches.Cable width: 12.5mm / 0.49 Inches..
- Withstand voltage: 300 V.Temperature: 105 Degree Centigrade..
- Used for most Atmel AVR JTAG debugger, system programmer, Isp download, etc..
Check StockXiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM
- 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
- This board is for Arduino PIC AVR DSP ARM.
- Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check StockWINGONEER Universal IC Adapter Socket LQFP TQFP QFP32 to DIP28 and TQFP32 to DIP32 IC Adapters for ATMEL AVR Chips
- Applicable for all ATMEL AVR series QFP32 chips.
- Applicable for all programmer: TL866CS/A/SP300U/ALL-100GANG/ALL-11 series/LT-48 series/SuperPRO series/TOP series .......
- Support chips: Atmega48 Atmega8 Atmega88 Atmega168....
- Package Include: 1 x QFP32 to DIP28 Adapter.
Check StockMybotOnline 5 Sets Stepper Motor 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board
- Stepper motor with a standard interface, motor diameter: 1.1", wire length: 9.05".
- A, B, C, D four-phase LED indicates the status of stepper motor work.
- Compatible with ArduinoIDE UNOR3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi.
- Gift: 1x 10-pin male to female multicolor breadboard jumper wires,each cable length: 7.87"(20 cm).
- Packing in a box: 5 sets Uln2003 stepper motor + driver board + 10 pin jumper wire.
Check StockWinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR
- 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
- Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
- Standard interface can be directly connected with microcontrollers..
- Red working status indicator for power on indication.Green working status indicator for relay the switch..
- It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock1.8 inch SPI TFT LCD Display Module for ST7735 128x160 51/AVR/STM32/ARM 8/16 bit
- This is a new 1.8 inch serial SPI color display module.
- Support analog SPI and hardware SPI. SPI serial, less I/O port need.
- Designed with one socket for sd card and PCB adapter for LCD.
- The LCD display module can be driven by 8051 / AVR / PIC /ARM/STM32.
- The 4D systems lcd display can be driven with at least four IO.
Check Stocksb components Air Monitoring Breakout, Air Monitor Module for Raspberry Pi, Beaglebone, Arduino, STM32, PIC, AVR, ARM, etc.
- Air Monitoring breakout, air monitoring module by SB Components.
- It provide the level of quantity of the suspended particulates with their mass.
- It has a powerful and hi-tech PMSA003 sensor that provides the information of suspended particulate matter.
- It communicates via UART(serial) with the standby current ≤200 Microampere(μA) of the sensor.
- Compatible with Raspberry Pi, Beaglebone, Arduino, STM32, PIC, AVR, ARM, etc..
Check StockALMOCN 6Pcs DC 5V 1 Channel Relay Module With Optocoupler Isolation Support High or Low Level Trigger
- The Relay Board Maximum load: AC 250V/10A, DC 30V/10A.
- Using SMD optocoupler isolation, strong driving capability, stable performance..
- Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications..
- Fault-tolerant design, even if the control line is broken, the relay will not move..
- Wide Application,The relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
Check StockLED LCD Universal TV Backlight Constant Current Backlight Lamp Driver Board Boost Step Up Module 10.8-24V to 15-80V 14-37 Inch
- This is a new 1.8 inch serial SPI color display module.
- Support analog SPI and hardware SPI. SPI serial, less I/O port need.
- Designed with one socket for sd card and PCB adapter for LCD.
- It can be driven by 8051 / AVR / PIC /ARM/STM32.
Check Stock