Reviews Atmega48v 10au - BestBuyersPro.com

NXP USA Inc. ARM Cortex-A9, ARM Cortex-M4 Microprocessor IC series 2 Core, 32-Bit 227MHz, 1GHz 400-MAPBGA (14x14) (Pack of 5)(SCIMX6X3EVK10ABR)

5Pcs/lot ATMEGA169PV-8AU ATMEGA169 Patch TQFP64 franchise MCU microprocessor chip ATMEGA169PV.

✔Using Atmel Atmega328P-AU MCU, Support ISP download,using the same chips ATmega328P and CH340 with the official version..
✔Support for external 5V~12V DC power supply, Support power supply by 9V battery..
✔Nano V3.0 ATMEGA328P improved version with 3pcs pin headers. No welding needed..

R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory..
R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). Comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files)..
This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..

MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY.
Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
Board for functionality similar to the compatible for Arduino Mega 2560..
The board used the chip CH340G as converter UART-USB..

Original ATmega328P CH340 chip is used. Improved new version CH340G Replace FT232RL..
LAFVIN Nano V3.0 card is 100% compatible with the Nano card, and fully compatible with Windows, Mac and Linux operating system..
Works the same as original Nano, runs perfectly on programming software..
Using Atmel Atmega328P-AU MCU, Support ISP download.
LAFVIN Nano CH340 controller is a compact board similar to the R3 board, smaller and breadboard-friendly than Diecimila..

The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). Comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files)..
This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..
R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory.R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
With this Ethernet Shield, for Arduino board can be used to connect to internet. Can be used as server or client. Directly plug puzzle board, no soldering required. It is directly compatible with Arduino official Ethernet Library. It adds a micro-SD card slot, which can be ....

1.Nano V3.0 card is 100% compatible with the Nano card, and fully compatible with Windows, Mac and Linux operating system..
2.It uses the chip ATmega328P CH340 instead of FT232RL. You can start with various electronic projects by using the Arduino software (IDE). It has....
3.It can be powered via USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27)..
4.Nano CH340 controller is a compact board similar to the UNO, smaller and breadboard-friendly than Diecimila..
5.Using Atmel Atmega328P-AU MCU, Support ISP download.

Bootloadered already in the board, easy to get started..
Support power supply by external 3.3V~12V DC power and 9V battery power..
Support serial downloading, 100% Compatible to all Pro MIni series shields and sensors..

【Same function as the original Arduino】It great for learning the basics of how sensors and actuators work, and an essential tool for your rapid prototyping needs.
【CHIP UPGRADE】Upgrade the main control chip to ATMEGA328P-AU.And it same as the original arduino pin layout. It compatible with all expansion boards..
【ADDED A 500MA SELF-RECOVERYFUSE】Compared with the original ARDUINO, a 500ma self-recovery fuse is added, which automatically disconnects the circuit when short-circuited to avoid component damage.Change the plug-in pins of the original ARDUINO to SMD pins to avoid short circuit of the development board contact conductors, which is safer..
【Added 10 LED marquees driven by MOS tubes】which avoids the problem of insufficient output current of the IO port of the single-chip microcomputer, and can directly drive a small DC motor through the IO port..
【EASY TO USE】Change the original USB-B type interface to MICRO-USB interface, which is more convenient to use..